Panasonic SA-NC9GC User manual

nAMPLIFIER SECTION
RMS Output Power: Dolby Digital Mode
Front Ch 95 W per channel (3 Ω), 1 kHz,
10% THD
Surround Ch 95 W per channel (3 Ω), 1 kHz,
10% THD
Center Ch 95 W per channel (3 Ω), 1 kHz,
10% THD
Subwoofer Ch 115 W per channel (3 Ω), 100 Hz,
10% THD
Total RMS Dolby Digital mode power
590 W
PMPO output power (For GC, GS & GCS only)
6500 W
DIN Output Power: Dolby Digital Mode
Front Ch 65 W per channel (3 Ω), 1 kHz,
10% THD
Surround Ch 65 W per channel (3 Ω), 1 kHz,
10% THD
Center Ch 65 W per channel (3 Ω), 1 kHz,
10% THD
Subwoofer Ch 75 W per channel (3 Ω), 100 Hz,
10% THD
Total DIN Dolby Digital mode power
400 W
nFM/AM TUNER, TERMINALS SECTION
©2007 Matsushita Electric Industrial Co. Ltd.. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
SA-NC9GC
SA-NC9GS
SA-NC9GCS
SA-NC9GN
Colour
(K)... Black Type
Preset stations FM 30 stations
AM 30 stations
Frequency Modulation (FM)
Frequency range 87.50 MHz to 108.00 MHz (50-kHz
step)
Sensitivity 4.0 µV (IHF)
S/N 26 dB 2.2 µV
A
ntenna terminals 75 Ω(unbalanced)
A
mplitude Modulation (AM)
Frequency range
For GC, GS & GCS only 522 kHz to 1629 kHz (9-kHz step)
520 kHz to 1630 kHz (10-kHz
step)
For GN only 522 kHz to 1629 kHz (9-kHz step)
A
M sensitivity S/N 20 dB at 999 kHz
1000 µV/m
Phone jack
Terminal Stereo, 3.5-mm jack
Mic jack (For GC, GS & GCS only)
Sensitivity 0.7 mV, 600 Ω
Terminal Mono, 6.3-mm jack (2 system)
Music Port jack (Front)
Sensitivity 100-mV, 10 kΩ
Terminal Stereo, 3.5-mm jack
USB jack
DVD Stereo System
Notes: This model’s DVD mechanism changer unit is DL2SV.
Specifications
ORDER NO. MD0703039CE

USB Standard USB 2.0 full speed 2.0
Media file format support MP3 (*.mp3), WMA (*.wma),
JPEG (*.Jpg, *JPEG), MPEG4
(*.asf)
USB device file system FAT16, FAT32
USB port power Max 500mA
nCASSETTE DECK SECTION
Track system 4-Track, 2 Channel
Head Record/Playback Solid Permalloy Head
Erasure Double Gap Ferrite Head
Motor DC Servo Motor
Recording System AC Bias 100 kHz
Erase System AC Erase 100 kHz
Tape Speed 4.8 cm/sec
Overall Frequency Response (+3, -6 dB) at DECK OUT
Normal 35 Hz to 14 kHz
S/N Ratio 50 dB (A weighted)
Wow and Flutter 0.18% (WRMS)
Fast Forward and Rewind Time Approx. 120 seconds with
C-60 cassette tape
nDISC SECTION
Disc played [8 cm or 12 cm]
(1) DVD (DVD-Video, DivX )
(2) DVD-RAM (DVD-VR, JPEG , MP3 , MPEG4 , DivX )
(3) DVD-R (DVD-Video, DVD-VR, JPEG , MP3 , MPEG4 ,
DivX# 1,#2)
(4) DVD-R DL (DVD-Video, DVD-VR)
(5) DVD-RW (DVD-Video, DVD-VR, JPEG , MP3 , MPEG4
2,#5, DivX# 1,#2)
(6) +R/ +RW (Video)
(7) +R DL (Video)
(8) CD,CD-R/RW [CD-DA, Video CD, SVCD , MP3 , WMA ,
JPEG# 2,#3, MPEG4# 2,#5, DivX# 1,#2, HighMAT Level 2 (Audio and
Image)]
Plays all versions of DivX video (including DivX 6) with standard
playback of DivX®media files. Certified to the DivX Home Theater
Profile. GMC (Global Motion Compensation) is not supported.
The total combined maximum number of recognizable audio,
picture and video contents and groups: 4000 audio, picture and video
contents and 400 groups.
Exif Ver 2.1 JPEG Baseline files
Picture resolution: between 160 x 120 and 6144 x 4096 pixels
(Sub sampling is 4:0:0, 4:2:0, 4:2:2 or 4:4:4). Extremely long and
narrow pictures may not be displayed.
MPEG-1 Layer 3, MPEG-2 Layer 3
MPEG4 data recorded with the Panasonic SD multi cameras or
DVD video recorders.
Conforming to SD VIDEO specifications (ASF standard) / MPEG4
(Simple Profile) video system / G.726 audio system
Conforming to IEC62107
Windows Media Audio Ver. 9.0 L3
Not compatible with Multiple Bit Rate (MBR)
Pick up
Wavelength (DVD/CD) 662 nm/785 nm
Laser power (DVD/CD) CLASS 1 / CLASS 1M
A
udio output (Disc)
Number of channels (FL,FR,C,SL,SR,SW),5.1ch
nVIDEO SECTION
Video system PAL625/50, PAL525/60, NTSC
Composite video output
Output level 1Vp-p(75Ω)
Terminal Pin jack (1 system)
S-video output
Y output level 1Vp-p(75Ω)
C output level 0.3 Vp-p (75 Ω)(PAL)
0.286 Vp-p (75 Ω)(NTSC)
Terminal S terminal (1 system)
Component video output
[NTSC : 480p / 480i, PAL: 576p / 576i]
Y output level 1Vp-p(75Ω)
PBoutput level 0.525 Vp-p (75 Ω)
PRoutput level 0.525 Vp-p (75 Ω)
Terminal
Pin jack (Y: green, PB:blue,P
R:red)(1system)
HDMI AV output
Terminal Type A connector (19-pin)
This unit supports “HDAVI Control 2” function.
nGENERAL
Power supply
For GC only AC 220 to 240 V, 50/60Hz
For GCS/GS only AC 110 to 127V/220 to 240 V,
50/60Hz
For GN only AC 230 to 240 V, 50Hz
Power consumption 165 W
Power consumption in standby mode:
0.9 W (approximate)
Dimensions (W x H x D) 205 x 385 x 342 mm
Mass appx. 7.1 kg
Operating temperature range +5to+35°C
Operating humidity range 5% to 90% RH (no condensation)
nSYSTEM
2
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN
#1,#2
#2,#3 #2,#4 #2,#5 #1,#2
#2,#3 #2,#4 #2,#5
#2,#3 #2,#4 #
#6 #2,#4 #2,#7
®®
#1
#2
#3
#4
#5
#6
#7

For information on speaker system, please refer to the original
Service Manual (Order No. MD0703042CE) for SB-WNC9GC-K,
(Order No. MD0703040CE) for SB-PF9GC-K & (Order No.
MD0703041CE) for SB-NC9GC-K.
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
3
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

1 Safety Precautions 6
1.1. General Guidelines 6
1.2. Safety Precaution for AC Power Supply Cord (For GS
only) 7
1.3. Before Use (For GS/GCS only) 7
1.4. Before Repair and Adjustment 7
1.5. Protection Circuitry 7
1.6. Safety Parts Information 8
2 Handling Precautions for Traverse Unit 9
2.1. Handling Optical Pickup 9
2.2. Replacing Precautions for Optical Pickup Unit 9
2.3. Grounding for Preventing Electrostatic Destruction 9
3 Precaution of Laser Diode 11
4 About Lead Free Solder (PbF) 12
4.1. Service caution based on legal restrictions 12
5 Accessories 13
6 Operation Procedures 15
6.1. Main Unit Key Buttons Operations 16
6.2. Remote Control Key Buttons Operations 17
6.3. Disc Information 18
6.4. DivX VOD Content 20
7 New Features 21
7.1. Using the VIERA Link 滴DAVI Control 剩22
8 About HighMAT 23
8.1. What 痴HighMAT? 23
8.2. Why take advantage of HighMAT? 23
8.3. Benefits of HighMAT? 24
9 Self diagnosis and special mode setting 27
9.1. Service Mode Summary Table 27
9.2. Service Mode Table (Main Unit) 27
9.3. DVD Self Diagnostic Function - Error Code 35
9.4. Doctor Mode 38
9.5. Sales Demonstration Lock Function 49
10 Assembling and Disassembling 50
10.1. Caution 50
10.2. Disassembly flow chart 52
10.3. Main Parts Location 53
10.4. Disassembly of Top Cabinet 54
10.5. Disassembly of Rear Block 54
10.6. Disassembly of DVD Changer Unit (DL2SV) & HDMI
P.C.B. 55
10.7. Disassembly of Main P.C.B. 56
10.8. Disassembly of Front Panel 56
10.9. Disassembly of Power P.C.B. & Speaker P.C.B. 57
10.10. Replacement for Power Amp IC 58
10.11. Disassembly of Panel P.C.B. 59
10.12. Disassembly of Sub Panel P.C.B. 59
10.13. Disassembly of Deck Mechanism Unit 60
10.14. Disassembly of Deck P.C.B. 60
10.15. Disassembly of Traverse Unit 60
10.16. Disassembly of Deck Mechanism Main Components 63
10.17. Disassembly of Deck Mechanism P.C.B. 65
10.18. Disassembly of cassette lid 65
10.19. Rectification for tape jam problem 66
10.20. Stacking of Surround Speaker & Speakers to enjoy Bi-
Amp TS Mode 66
11 Service Positions 68
11.1. Checking and Repairing of Main P.C.B. & DVD Module
P.C.B. 68
11.2. Checking and Repairing of HDMI P.C.B. 69
11.3. Checking and Repairing of Deck & Deck Mechanism
P.C.B. 70
11.4. Checking and Repairing of Power & Speaker P.C.B. 71
11.5. Checking and Repairing of Panel P.C.B. 72
12 Procedure for Checking Operation of Individual Parts of Deck
Mechanism Unit 73
12.1. Operation Check with Cassette Tape 73
12.2. Operation Check without Cassette Tape 73
13 Measurement And Adjustments 75
13.1. Cassette Deck Section 75
14 Voltage and Waveform Chart 77
14.1. DVD Module P.C.B. 77
14.2. Main P.C.B. 79
14.3. Panel P.C.B. 81
14.4. Power P.C.B. 82
14.5. Sub Heat Sink P.C.B. 82
14.6. Sub Panel P.C.B. 82
14.7. Transformer P.C.B. 83
14.8. Tray Loading P.C.B. 83
14.9. Deck P.C.B. & Deck Mechanism P.C.B. 83
14.10. Waveform Chart 84
15 Wiring Connection Diagram 87
16 Block Diagram 89
16.1. DVD 89
16.2. Main 92
16.3. Panel/Sub Panel/USB Relay 95
16.4. Power 96
16.5. Transformer 97
16.6. Deck/Deck Mechanism/Tray Loading 98
17 Notes of Schematic Diagrams 99
CONTENTS
Page Page
4
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

18 Schematic Diagram 101
18.1. (A) DVD Module (DV5.0) Circuit 101
18.2. (A) DVD Module (HDMI) Circuit 105
18.3. (B) Main Circuit 106
18.4. (C) Panel Circuit 110
18.5. (D) Sub Panel Circuit 111
18.6. (E) Power Circuit 112
18.7. (F) Speaker Circuit 114
18.8. (G) Transformer Circuit 115
18.9. (H) Sub Heat Sink Circuit 116
18.10. (I) Deck Circuit 117
18.11. (J) Deck Mechanism Circuit, (K) Relay Circuit & (L) Tray
Loading Circuit 118
18.12. Optical Pickup Unit Circuit 119
19 Printed Circuit Board 121
19.1. (A) DVD Module P.C.B. (Side A & B ) 122
19.2. (B) Main P.C.B. 123
19.3. (C) Panel P.C.B. & (D) Sub Panel P.C.B. 124
19.4. (E) Power P.C.B., (F) Speaker P.C.B., (G) Transformer
P.C.B. & (H) Sub Heat Sink P.C.B. 125
19.5. (I) Deck P.C.B. , (J) Deck Mechanism P.C.B., (K) Relay
P.C.B. & (L) Tray Loading P.C.B. 126
20 Basic Troubleshooting Guide 127
20.1. Basic Troubleshooting Guide for Traverse Unit (DVD
Module P.C.B.) 127
20.2. Basic Troubleshooting Guide for HDMI AV output 127
21 Illustration of ICs, Transistors and Diodes 129
22 Terminal Function of IC
131
22.1. IC2600 (C2CBYY000451
) System Microprocessor
131
23 Exploded Views 133
23.1. Cabinet Parts Location 133
23.2. Deck Mechanism Parts Location (RAA4111-S) 136
23.3. Packaging 137
24 Replacement Parts List 139
5
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to the chassis, the reading must be .
1.1.2. Leakage Current Hot Check
(See Figure 1)
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitor, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may
be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is out of the limits
specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to
the customer.
Figure 1
6
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

1.2. Safety Precaution for AC Power Supply Cord (For GS only)
1.3. Before Use (For GS/GCS only)
Be sure to disconnect the mains cord before adjusting the voltage selector.
Use a minus(-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will
be used. (If the power supply in your area is 110V or 127V, set to the “127V” position.)
Note that this unit will be seriously damaged if this setting is not made correctly. (There is no voltage selector for some countries,
the correct voltage is already set.)
1.4. Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C5951 through a 10Ω, 5W resistor to ground.
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 110 ~ 127V, 50 / 60 Hz in NO SIGNAL (vol. min, at CD mode) should be ~900mA. [For GCS/GS only]
Current consumption at AC 220 ~ 240V, 50 / 60 Hz in NO SIGNAL (vol. min, at CD mode) should be ~500mA . [For GC/GCS/GS
only]
Current consumption at AC 230 ~ 240V, 50 Hz in NO SIGNAL (vol. min, at CD mode) should be ~500mA . [For GN only]
1.5. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
· No sound is heard when the power is turned on.
· Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
7
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

Note :
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.6. Safety Parts Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts
should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design
without permission of manufacturer.
Table 1
Reference No. Part No. Part Name & Description Remarks
360 RAE2024Z-S TRAVERSE UNIT (AFTER
ALIGNMENT)
[M]
A2 K2CQ2CA00002 AC CORD [M]GC/GS/GCS
A2 K2CJ2DA00010 AC CORD [M]GN
C5251 F2A1V4710036 470 35V [M]
C5252 F2A1V4710036 470 35V [M]
C5351 F2A1V4710036 470 35V [M]
C5352 F2A1V4710036 470 35V [M]
C5451 F2A1V4710036 470 35V [M]
C5452 F2A1V4710036 470 35V [M]
C5512 F2A1V1020084 1000 35V [M]
C5513 F2A1V1020084 1000 35V [M]
C5951 ECQU2A104MLC 0.1 100V [M]
D5744 B0JCAE000001 DIODE [M]
F1 K5D252BLA013 2.5A FUSE [M]GC
F1 K5D502BLA013 FUSE [M]GCS
F2 K5D252BLA013 2.5A FUSE [M]GCS
FP5920 K5G103A00019 FUSE PROTECTOR [M]
FP5940 K5G103A00019 FUSE PROTECTOR [M]
FP5950 K5G502A00039 FUSE PROTECTOR [M]
RL5950 K6B1AEA00003 MAGNETRELAYS [M]
JK5950 K2AA2B000011 JK AC INLET [M]
L5950 ELF15N035AN LINE FILTER [M]
L5951 ELF15N035AN LINE FILTER [M]
T5950 G4CYAYY00141 TRANSFORMER [M]
T5951 G4C2AAJ00005 BACK-UP TRANSFORMER [M]
Z5950 ERZV10V511CS ZENER [M]
R5271 ERJ3GEYJ102V 1K 1/16W [M]
8
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

2 Handling Precautions for Traverse Unit
The laser diode used inside optical pickup could be destroyed due to static electricity as a potential difference is caused by
electrostatic load discharged from clothes or human body. Handling the parts carefully to avoid electrostatic destruction during
repair.
2.1. Handling Optical Pickup
1. Do not impact on optical pickup as the unit structurally uses an extremely precise technology.
2. Short-circuit the flexible cable of optical pickup remove from the circuit board using a short-circuit pin or clip in order to prevent
laser diode from electrostatic destruction (Refer to Fig. 3.1 and Fig. 3.2)
3. Do not handle flexible cables forcibly as this may cause snapping. Handle the parts carefully (Refer to Fig. 3.1)
4. A new optical pickup is equipped with an anti-static flexible cable. After replacing and connecting to the flexible board, cut the
anti-static flexible cable. (Refer to Fig. 3.1)
Fig. 3.1
2.2. Replacing Precautions for Optical Pickup Unit
CD/DVD Optical Pickup
The optical pickup by which part supply was carried out attaches the short clip to the flexible board for laser diode electrostatic
discharge damage prevention. Please remove the short clip and be sure to check that the short land is open, before connecting.
(Please remove solder, when the short land short-circuits.)
2.3. Grounding for Preventing Electrostatic Destruction
1. Human body grounding
Use the anti-static wrist strap to discharge the static electricity accumulated in your body. (Refer to Fig. 3.2)
2. Work place grounding
Place a conductive material (conductive sheet) or ironboard where optical pickup is placed. (Refer to Fig. 3.2)
Note :
Keep your clothes away from optical pickup as wrist strap does not release the static electricity charged in clothes.
9
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

Fig. 3.2
10
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

3 Precaution of Laser Diode
Caution :
This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens.
Wavelength : 785 nm(CD)/662 nm(DVD)
Maximum output radiation power from pick up : 100 µW/VDE
Laser radiation from pick up unit is safety level, but be sure the followings:
1. Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pick up unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pick up lens for a long time.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
nUse of Caution Labels
11
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

4 About Lead Free Solder (PbF)
4.1. Service caution based on legal restrictions
4.1.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)
Service caution for repair work using Lead Free Solder (PbF)
· The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
· To put lead free solder, it should be well molten and mixed with the original lead free solder.
· Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
· Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt
the lead free solder.
· Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30
degrees C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
· The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
12
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

5 Accessories
Remote control
AC power
supply cord
(For GC/GCS
only)
AC power
supply cord (For
GS only)
AC power
supply cord
(For GN only)
FM indoor
antenna
AM loop
antenna
Video cable
Speaker cables
13
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

Speaker cable
sticker
Metal brackets (x
6)
Short
screws (x
12)
Long
screws (x
4)
Lock covers (x 6)
Base stands (x
2)
Allen Key
14
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

6 Operation Procedures
15
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

6.1. Main Unit Key Buttons Operations
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN
16

6.2. Remote Control Key Buttons Operations
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN
17

6.3.1. Disc Playability
6.3. Disc Information
18
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

6.3.2. To Play MP3/ WMA and still Pictures (JPEG)
19
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN

6.4. DivX VOD Content
20
SA-NC9GC / SA-NC9GS / SA-NC9GCS / SA-NC9GN