Panasonic SAAK22 - MINI HES W/CD-PLAYER User manual

ORDER NO. MD0105096C2
CD Stereo System
SA-AK22
Colour
(S)... Silver Type
Area
(E)... Europe
(EB)... Great Britain
(EG)... Germany and Italy
TAPE SECTION :
SG-2W MECHANISM SERIES
CD SECTION :
RAE0152Z-3 TRAVERSE DECK SERIES
SPECIFICATIONS
Specifications
1
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

AMPLIFIER SECTION
RMS power output
THD 10%, both channels driven
both channel driven
(E,EB) 80 W per channel (6 )
(EG) 60 W per channel (6 )
Input sensitivity
AUX 250 mV
Input Impedance
AUX 13 k
FM TUNER SECTION
Frequency range 87.50 - 108.00 MHz (50 kHz
steps)
Sensitivity 1.8 V (IHF)
S/N 26 dB 1.5 V
Antenna terminal(s) 75 (unbalanced)
AM TUNER SECTION
Frequency range 522 - 1629 kHz (9 kHz steps)
Sensitivity
S/N 20 dB (at 999 kHz) 560 V/m
CASSETTE DECK SECTION
Track system 4 track, 2 channel
Heads
Record/playback Solid permalloy head
Erasure Double gap ferrite head
Motor DC servo motor
Recording system AC bias 100 kHz
Erasing system AC erase 100 kHz
Tape speed 4.8 cm/s
Frequency response (+3 dB, -6 dB at DECK OUT)
NORMAL (TYPE I) 35 Hz - 14 kHz
S/N 50 dB (A weighted)
Wow and flutter 0.18% (WRMS)
Fast forward and rewind time Approx. 120 seconds with
C-60 cassette tape
CD SECTION
Sampling frequency 44.1 kHz
Decoding 16 bit linear
Beam source/wave length Semiconductor laser/780 nm
Number of channels Stereo
Frequency response 20 Hz - 20 kHz (+1, -2 dB)
Wow and flutter Below measurable limit
Digital filter 8 fs
D/A converter MASH (1 bit DAC)
GENERAL
Power supply
(E,EG) AC 230-240V, 50 Hz
(EB) AC 230, 50 Hz
Power consumption 170 W
Power consumption in standby mode
0.4 W
2
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

Dimensions (W x H x D) 250 x 332 x 316 mm
Mass 8.2 kg
SYSTEM
SC-AK22 (E) Music Center: SA-AK22 (E)
Speaker: SB-AK22 (E)
SC-AK22 (EB) Music Center: SA-AK22 (EB)
Speaker: SB-AK22 (E)
SC-AK22 (EG) Music Center: SA-AK22 (EG)
Speaker: SB-AK22 (E)
Notes:
1. Specifications are subject to change without notice. Weight and
dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum analyzer.
2001 Matsushita Electronics (S) Pte. Ltd. All rights reserved.
Unauthorized copying and distribution is a violation of law.
1. Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C536, C545, C546 through a 10 , 5W
resistor to ground.
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid
state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 230 V, 50 Hz in NO SIGNAL mode should be ~400mA.
2. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
- No sound is heard when the power is turned on.
- Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative
speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the
amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off
and then on again.
3
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

3. Accessories
Remote Control Transmitter
FM indoor antenna (E,EB)
FM indoor antenna (EG)
AC mains lead (E,EG)
AC mains lead (EB)
AM Loop antenna
4
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

Antenna Plug Adaptor (EB)
4. Handling Precautions For Traverse Deck
The laser diode in the traverse deck (optical pickup) may break down due to potential difference
caused by static electricity of clothes or human body.
So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
- Handling of traverse deck (optical pickup)
1. Do not subject the traverse deck (optical pickup) to static electricity as
it is extremely sensitive to electrical shock.
2. The short land between the No.4(LD) and No.5(GND) pins on the
flexible board (FFC) is shorted with a solder build-up to prevent
damage to the laser diode.To connect to the PC board, be sure to open
by removing the solder build-up, and finish the work quickly.
3. Take care not to apply excessive stress to the flexible board (FFC).
4. Do not turn the variable resistor (laser power adjustment). It has
already been adjusted.
5
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

- Grounding for electrostatic breakdown prevention
1. Human body grounding
Use the anti-static wrist strap to discharge the static electricity from
your body.
2. Work table grounding
Put a conductive material (sheet) or steel sheet on the area where the
traverse deck (optical pickup) is placed, and ground the sheet.
Caution :
The static electricity of your clothes will not be grounded through the
wrist strap. So, take care not to let your clothes touch the traverse
deck (optical pickup).
Caution when Replacing the Traverse Deck :
The traverse deck has a short point shorted with solder to protect the
laser diode against electrostatics breakdown. Be sure to remove the
solder from the short point before making connections.
6
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

5. Precaution of Laser Diode
Caution :
This product utilizes a laser diode with the unit turned "ON", invisible
laser radiation is emitted from the pick up lens. / Wavelength : 780 nm /
Maximum output radiation power from pick up : 100 W/VDE / Laser
radiation from pick up unit is safety level, but be sure the followings:
1. Do not disassemble the optical pick up unit, since radiation from
exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pick up unit. It was already
adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pick up lens for a long time.
ACHTUNG :
Dieses Produkt enthält eine Laserdiode. Im eingeschalteten Zustand
wird unsichtbare Laserstrahlung von der Lasereinheit abgestrahlt. /
Wellenlänge : 780nm / Maximale Strahlungsleistung der Lasereinheit :
100 W/VDE / Die Strahlung an der Lasereinheit ist ungefährlich, wenn
folgende Punkte beachtet werden:
1. Die Lasereinheit nicht zerlegen, da die Strahlung an der freigelegten
Laserdiode gefährlich ist.
2. Den werkseitig justierten Einstellregler der Lasereinhit nicht verstellen.
3. Nicht mit optischen Instrumenten in die Fokussierlinse blicken.
4. Nicht über längere Zeit in die Fokussierlinse blicken.
ADVARSEL: I dette a apparat anvendes laser.
7
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Use of Caution Labels
6. Caution for AC Mains Lead
8
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

7. Operation Procedures
9
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland

10
www.freeservicemanuals.info
12/10/2014
Digitized in Heiloo, Holland