Panasonic SC-HC27 User manual

3 Connect the AC mains lead.
Power consumption in standby mode: 0.2 W
(approximate)
Do not use an AC mains lead from other equipment.
Note:
• Some settings return to default when you disconnect the
system.
• These speakers do not have magnetic shielding. Do
not put them near TVs, PCs or other equipment easily
influenced by magnetism.
• You cannot remove the net of the speakers.
To household mains socket
Operating Instructions
Compact Stereo System
Model No. SC-HC27
GN
Panasonic Corporation
Web Site: http://panasonic.net
© Panasonic Corporation 2012 RQT9577-1L
L0212HH1052
En
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Please keep this manual for future reference.
Bottom of product
Inside of product
WARNING!
Unit
• To reduce the risk of fire, electric shock or product
damage,
– Do not expose this unit to rain, moisture, dripping or
splashing.
– Do not place objects filled with liquids, such as vases,
on this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to
qualified service personnel.
Battery
• Risk of fire, explosion and burns. Do not recharge,
disassemble, heat above 60°C or incinerate.
• Keep the button-type battery out of the reach of children.
Never put button-type battery in mouth. If swallowed call
your doctor.
Product Identification Marking is located on the bottom
of the unit.
CAUTION!
Unit
• To reduce the risk of fire, electric shock or product
damage,
– Do not install or place this unit in a bookcase, built-in
cabinet or in another confined space. Ensure this unit is
well ventilated.
– Do not obstruct this unit’s ventilation openings with
newspapers, tablecloths, curtains, and similar items.
– Do not place sources of naked flames, such as lighted
candles, on this unit.
• This unit is intended for use in moderate climates.
• Install this unit so that the AC mains lead can be
unplugged from the socket outlet immediately if any
problem occurs.
• This unit may receive radio interference caused by mobile
telephones during use. If such interference occurs, please
increase separation between this unit and the mobile
telephone.
• This unit utilizes a laser. Use of controls or adjustments
or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Battery
• Danger of explosion if battery is incorrectly replaced.
Replace only with the type recommended by the
manufacturer.
• When disposing the batteries, please contact your local
authorities or dealer and ask for the correct method of
disposal.
• Do not heat or expose to flame.
• Do not leave the battery(ies) in a car exposed to direct
sunlight for a long period of time with doors and windows
closed.
– If you see this symbol –
Information on Disposal in other Countries outside
the European Union
This symbol is only valid in the
European Union.
If you wish to discard this product,
please contact your local authorities or
dealer and ask for the correct method
of disposal.
Supplied accessories
Check and identify the supplied accessories.
1 x AC mains lead
1 x FM indoor antenna
1 x AM loop antenna
1 x Remote control
(with a battery)
(N2QAYC000059)
1 Connect the FM indoor antenna.
Place the antenna where reception is best.
2 Connect the AM loop antenna.
Tape
Click!
Getting started
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and has been
certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, or
iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries.
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
Amplifier section
RMS output power stereo mode
Front Ch (both ch driven)
5 W per channel (6 ), 1 kHz, 10% THD
Total RMS stereo mode power 10 W
Tuner section
Preset station FM 30 stations
AM 15 stations
Frequency modulation (FM)
Frequency range
87.50 MHz to 108.00 MHz (50 kHz step)
Antenna terminals 75
(unbalanced)
Amplitude modulation (AM)
Frequency range 522 kHz to 1629 kHz (9 kHz step)
520 kHz to 1630 kHz (10 kHz step)
Terminals section
USB port
USB standard USB 2.0 full speed
Media file format support MP3 (*.mp3)
USB device file system FAT12, FAT16, FAT32
USB port power DC OUT 5 V, 500 mA MAX
iPod connector DC OUT 5 V, 1.0 A MAX
Headphones jack
Terminal Stereo, 3.5 mm jack
Disc section
Disc played (8 cm or 12 cm)
CD, CD-R/RW (CD-DA, MP3 )
Pick up
Wavelength 790 nm (CD)
Laser power CLASS 1
Audio output (Disc)
Number of channels 2 ch (FL, FR)
FL = Front left channel
FR = Front right channel
MPEG-1 Layer 3, MPEG-2 Layer 3
Speaker section
Type 1 way, 1 speaker system (bass reflex)
Speaker unit(s)
Full range 8 cm cone type x 1/ch
Impedance 6
Specifications
Preparing the remote control
Before using
Replacing the battery
Replace with a new battery (CR2025 lithium battery).
1 While pressing the stopper, pull out the battery
holder.
2 Insert a new battery with the (+) side facing up.
3 Push the battery holder back fully.
Insulation sheet
CR2025
Overview of controls
A Standby/on switch [`], [1]
• Press to switch the unit from on to standby mode or
vice versa. In standby mode, the unit is still consuming
a small amount of power.
B Select audio source
C Basic playback control
D View the clock and timer options
E View the iPod menu
View information
F Select the sound effects
G Select the option
Skip album
MUTESETUP
DISPLAY
SOUND
ALBUM
PLAY MENU
iPod MENU
SLEEP
iPod
RADIO/
USB
CD
DIMMER
OK
H Set the sleep timer
I Decrease the brightness of the display panel
• Press the button again to cancel.
J Adjust the volume of the system
K Mute the sound of the system
• Press the button again to cancel.
• “MUTE” is also cancelled when you adjust the volume
or when you switch off the system.
L View the play menu
View the radio options
M USB port ( )
N Headphones jack ( )
• Plug type: Ø 3.5 mm stereo (not supplied)
• Avoid listening for prolonged periods of time to prevent
hearing damage.
• Excessive sound pressure from earphones and
headphones can cause hearing loss.
• Listening at full volume for long periods may damage
the user’s ears.
O Open or close the sliding door
P Sliding door
Q Remote control sensor
• Maximum range: 7 m directly in front
R Display panel
S Open or close the dock for iPod/iPhone
AB OJC
NM
Top view
Front view
RQP
S
General
Power supply AC 220 to 240 V, 50 Hz
Power consumption 19 W
Dimensions (W x H x D) 400 mm x 213 mm x 110 mm
[D = 72 mm (min)]
[D = 144 mm (tray open)]
Mass 2 kg
Operating temperature range 0°C to +40°C
Operating humidity range
35% to 80% RH (no condensation)
Power consumption in standby mode
0.2 W (approximate)
Note:
• Specifications are subject to change without notice.
Mass and dimensions are approximate.
• Total harmonic distortion is measured by the digital
spectrum analyzer.
Maintenance
To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this
system.
• Before using chemically treated cloth, read the instructions
that came with the cloth carefully.
Do the procedures with the remote control. You can also use the buttons on the main unit if they are the same.
Your system and the illustrations can look differently.
Safety precautions
HC27_GN1_en.indd 1HC27_GN1_en.indd 1 5/18/2012 1:34:23 PM5/18/2012 1:34:23 PM

Inserting or removing media
iPod/iPhone
Push [iPod x] to open the dock tray.
iPod/iPhone
(not supplied)
Dock adapter
(not supplied)
Connector
Note:
• Make sure to remove the iPod/iPhone from its case.
• Make sure to align your iPod/iPhone with the connector
when inserting.
• Use a compatible dock adapter.
• If a dock adapter is not available, insert and remove the
iPod/iPhone with care.
Disc
Press [CD xOPEN/CLOSE] on the main unit to open the
sliding door.
Put in a disc with the label facing towards you.
Note:
Keep fingers away from the sliding door when it is closing.
Click!
USB
Note:
Do not use a USB extension cable. The system cannot
recognise USB device connected through a cable.
Basic playback
iPod CD USB
Press [iPod], [CD] or [USB] to select the source.
Play Press [4/9].
Stop Press [8].
USB
:
The track is memorised.
“RESUME” is shown.
Press two times to stop fully.
Pause Press [4/9].
Press again to continue playback.
Skip track Press [2/3] or [5/6].
Search through
track
Press and hold [2/3] or
[5/6].
USB device
(not supplied)
iPod/iPhone
iPod
View iPod menu Press [iPod MENU].
Select an item Press [R, T] and then press [OK].
Note:
• Depending on the model, it may be necessary to remove
the iPod/iPhone and select the album, artist, etc. on the
iPod/iPhone.
• Operation results may vary depending on the iPod/iPhone
models.
• Read the User Guide of the iPod/iPhone for the operating
instructions.
Disc, USB
CD USB
Skip album Press [R, T].
View information Press [DISPLAY].
Note:
• Maximum characters that can be shown: approximately 32
• This system supports ver. 1.0, 1.1 and 2.3 ID3 tags.
• Text data that the system does not support can show
differently.
30 FM and 15 AM stations can be preset.
Preparation
Connect the antennas (Z“Getting started”).
Press [RADIO] to select “FM” or “AM”.
Automatic presetting
1 Press [PLAY MENU] to select “A.PRESET”.
2 Press [R, T] to select “LOWEST” or “CURRENT”
frequency.
LOWEST : To begin auto preset from the lowest
frequency.
CURRENT : To begin auto preset from the current
frequency .
To change the frequency, refer to “Manual tuning and
presetting”.
3 Press [OK] to start presetting.
The tuner presets all the stations it can receive into the
channels in ascending order.
To cancel, press [8].
Manual tuning and presetting
1 Press [PLAY MENU] to select “TUNEMODE”.
2 Press [R, T] to select “MANUAL” and then press
[OK].
3 Press [2/3] or [5/6] to tune in to the
station.
To tune automatically, press and hold the button until the
frequency starts changing quickly.
“STEREO” is shown when the system is tuned in to a
stereo broadcast.
Setting the clock
This is a 24-hour clock.
1 Press [SETUP] to select “CLOCK”.
2 Press [R, T] to set the time.
3 Press [OK].
To show the clock for a few seconds
Press [SETUP] to select “CLOCK” and then press [OK].
Note:
Reset the clock regularly to maintain accuracy.
Sleep timer
The sleep timer switches off the system after the set time.
Press [SLEEP] to select the setting (in minutes).
To cancel, select “OFF”.
SLEEP 30 →SLEEP 60 →SLEEP 90 →SLEEP120
OFF
Note:
• The remaining time is always shown on the display.
The display changes temporarily when you perform other
operations.
• The sleep timer can be used together with the play timer.
• The sleep timer always comes first. Be sure not to set an
overlap of timers.
Sound effects
1 Press [SOUND] to select a sound effect.
2 Press [R, T] to select the desired setting.
PRESET EQ “HEAVY” : Adds punch to rock.
“SOFT” : For background music.
“CLEAR” : Clarifies higher frequencies.
“VOCAL” : Adds gloss to vocal.
“FLAT” : Cancels the sound effect.
BASS “BASS -4” to “BASS +4”.
TREBLE “TREBLE-4” to “TREBLE+4”.
D.BASS “ON D.BASS” or “OFF D.BASS”.
SURROUND “ON SURROUND” or
“OFF SURROUND”.
Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated do not solve the problem, consult your
dealer for instructions.
Common problems
No operations can be done with the remote control.
• Examine that the battery is installed correctly.
• The remote control and this unit are using different codes
(Zright, “REMOTE ”).
Sound is distorted or no sound.
• Adjust the volume of the system.
• Examine the volume of the iPod/iPhone.
• Switch off the system, determine and correct the cause,
then switch the system on again. It can be caused by
straining of the speakers through excessive volume or
power, and when using the system in a hot environment.
A “humming” sound can be heard during playback.
• An AC mains lead or fluorescent light is near the cable.
Keep other appliances and cords away from the cable of
this system.
iPod/iPhone
You cannot switch on the iPod/iPhone.
• Examine that the battery of the iPod/iPhone is not
depleted.
• Switch off the iPod/iPhone and the system before you
connect the iPod/iPhone. Connect the iPod/iPhone and
try again.
iPod/iPhone does not charge.
• Examine the connection.
Disc
Display not shown correctly.
Playback does not start.
• You did not put the disc in correctly. Put it in correctly.
• Disc is dirty. Clean the disc.
• Replace the disc if it is scratched, warped, or
non-standard.
• There is condensation. Let the system dry for 1 to 2 hours.
USB
The USB device or the contents in it cannot be read.
• The format of the USB device or the contents in it is/are
not compatible with the system.
• USB devices with storage capacity of more than 32 GB
cannot work in some conditions.
Slow operation of the USB device.
• Large content size or large memory USB device takes
longer time to read.
The elapsed time shown is different from the actual play
time.
• Transfer the data to another USB device or backup the
data and reformat the USB device.
Radio
A beat sound is heard.
• Switch off the TV or move it away from the system.
• Move mobile telephones away from the unit if the
interference is apparent.
A low hum is heard during AM broadcasts.
• Move the antenna away from other cables and cords.
Stations cannot be selected.
• Change the AM frequency step (Z“AM allocation
setting”).
Play menu
CD USB
1 Press [PLAY MENU] to select “PLAYMODE” or
“REPEAT”.
2 Press [R, T] and then press [OK] to select the
desired mode.
PLAYMODE
OFF
PLAYMODE
Play all tracks.
1-TRACK
1
Play one selected track.
Press [2/3] or [5/6] to select
the track.
1-ALBUM
1
Play one selected album.
Press [R, T] to select the album.
RANDOM
RND
Play all tracks randomly.
1-ALBUM
RANDOM
1 RND
Play all tracks in one selected album
randomly.
Press [R, T] to select the album.
REPEAT
ON REPEAT Repeat playback.
OFF REPEAT Cancel repeat playback.
Note:
• During random playback, you cannot skip to tracks which
have been played.
• The setting returns to default when you open the sliding
door.
Play timer
You can set the timer to come on at a certain time to wake
you up.
Preparation
Set the clock.
1 Press [SETUP] to select “TIMER ADJ”.
2 Press [R, T] to set the start time.
3 Press [OK].
4 Do steps 2 and 3 again to set the end time.
To start the timer
1 Prepare the audio source you want to listen to and
set the volume.
2 Press [SETUP] to select “TIMER SET”.
3 Press [R, T] to select “SET” and then press [OK].
“#” is shown.
The system must be switched off for the timer to
operate.
Check the
settings
1. Press [SETUP] to select “TIMER ADJ”.
2. Press [OK].
Cancel 1. Press [SETUP] to select “TIMER SET”.
2. Press [R, T] to select “OFF” and then
press [OK].
Note:
• The timer starts at a low volume and increases gradually
to the preset level.
• The timer comes on at the set time every day if the timer
is on.
• If you switch off the system and switch on again while a
timer is in operation, the timer will not stop at the end time.
Compatible media
iPod/iPhone (as of February 2012)
Update your iPod/iPhone with the latest software before
using this system.
iPod touch
1st, 2nd, 3rd and 4th generation
iPod nano
2nd, 3rd, 4th, 5th and 6th generation
iPod classic
iPhone 4S / iPhone 4 / iPhone 3GS / iPhone 3G /
iPhone
Charging an iPod/iPhone
An iPod/iPhone is charged automatically when connected to
the system (even when the system is in standby mode).
• See the iPod/iPhone display for its battery charging status.
• Disconnect the iPod/iPhone if it is not used for an
extended period of time after charging is complete
• Charging stops when the battery is fully charged. The
battery will deplete naturally.
Disc
• This system can play CD-R/RW with CD-DA or MP3
format content.
• Some CD-R/RW cannot be played because of the
condition of the recording.
• MP3 files are defined as tracks and folders are defined as
albums.
• This system can access up to:
– CD-DA : 99 tracks
– MP3 : 999 tracks, 255 albums (including root folder)
and 20 sessions
• Disc must conform to ISO9660 level 1 or 2 (except for
extended formats).
• Recordings will not necessarily be played in the order you
recorded them.
USB
• Compatible USB devices which are defined as mass
storage class:
– USB devices that support bulk-only transfer
– USB devices that support USB 2.0 full speed
• Files are defined as tracks and folders are defined as
albums.
• Track must have the extension “.mp3” or “.MP3”.
• This system can access up to:
– 255 albums (including root folder)
– 2500 tracks
– 999 tracks in one album
• CBI (Control/Bulk/Interrupt) is not supported.
• NTFS file system is not supported (only FAT 12/16/32 file
system is supported).
• Some files can fail to work because of the sector size.
iPod/iPhone, Disc, USB
To preset the station
4 Press [OK].
5 Press [R, T] to select a preset number.
6 Press [OK].
Do steps 3 through 6 again to preset more stations.
Note:
A station previously stored is overwritten when another
station is stored in the same preset number.
Selecting a preset station
1 Press [PLAY MENU] to select “TUNEMODE”.
2 Press [R, T] to select “PRESET” and then press
[OK].
3 Press [2/3] or [5/6] to select the preset
station.
Improving the sound quality
When “FM” is selected
1 Press [PLAY MENU] to select “FM MODE”.
2 Press [R, T] to select “MONO” and then press [OK].
To cancel, select “STEREO”.
“MONO” is also cancelled when you change the
frequency.
To memorise the setting
Continue with steps 4 through 6 of “Manual tuning and
presetting”.
Checking the signal status
Press [DISPLAY].
FM The FM signal is in monaural.
The system is not tuned in to a station.
FM ST The FM signal is in stereo.
FM MONO “MONO” is selected as the “FM MODE”.
AM allocation setting (by main unit only)
This system can also receive AM broadcasts allocated in
10 kHz steps.
1 Press [RADIO] to select “AM”.
2 Press and hold [RADIO].
After a few seconds, the display panel shows the current
minimum radio frequency. Release the button when the
minimum frequency changes.
• To go back to the initial setting, do the above steps again.
• After you change the setting, preset frequencies are
erased.
Radio
Main unit displays
“--:--”
• You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
“ADJUST CLOCK”
• Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
• Play timer is not set. Adjust the play timer accordingly.
“ERROR”
• An incorrect operation was done. Read the instructions
and try again.
“F61”
• There is a power supply problem.
“IPOD OVER CURRENT ERROR” or
“USB OVER CURRENT ERROR”
• The iPod/iPhone or USB device is drawing too much
power. Remove the iPod/iPhone or USB device. Switch
the system off and on again.
“NODEVICE”
• The iPod/iPhone or USB device is not connected.
Examine the connection.
“NO DISC”
• You have not put in a disc.
“NO PLAY”
• You have put in a disc that the system cannot play.
• You have inserted a USB device that cannot be played.
Examine the content. You can only play supported format.
• If there are more than 255 albums or folders (audio
and non-audio), some of the MP3 files in these albums
cannot be read and played. Transfer these music albums
to another USB device. Alternatively, reformat the USB
device and save these music albums prior to saving the
other non-audio folders.
Clock and timers
Auto off function
iPod CD USB
This function switches off the system (except in radio
source) if you do not use the system for approximately
30 minutes.
1 Press [SETUP] to select “AUTO OFF”.
2 Press [R, T] to select “ON” or “OFF” and then press
[OK].
Troubleshooting
“NOT MP3/ERROR”
• An unsupported MP3 format. The system will skip that
track and play the next one.
“NOT SUPPORTED”
• You have inserted an iPod/iPhone that cannot be played.
• If the iPod/iPhone is compatible, remove the iPod/iPhone
and connect it again. Examine that the battery of the iPod/
iPhone is not depleted.
“REMOTE ” (“ ” stands for a number.)
• The remote control and this unit are using different codes.
Change the code of the remote control.
– When “REMOTE 1” is shown, press and hold [OK] and
[T] for a minimum of 4 seconds.
– When “REMOTE 2” is shown, press and hold [OK] and
[R] for a minimum of 4 seconds.
“–VBR–”
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Memory reset (initialisation)
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1 Disconnect the AC mains lead.
Wait 3 minutes before you continue with step 2.
2 While you press and hold [1] on the main unit,
connect the AC mains lead again.
“– – – – – – – –” is shown.
3 Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
Remote control code
When other Panasonic equipment responds to the remote
control of this system, change the remote control code for
this system.
To set the code to “REMOTE 2”
1 Press and hold [CD] on the main unit and [R] on the
remote control until “REMOTE 2” is shown.
2 Press and hold [OK] and [R] for a minimum of
4 seconds.
To set the code to “REMOTE 1”
1 Press and hold [CD] on the main unit and [T] on the
remote control until “REMOTE 1” is shown.
2 Press and hold [OK] and [T] for a minimum of
4 seconds.
HC27_GN1_en.indd 2HC27_GN1_en.indd 2 5/18/2012 1:34:26 PM5/18/2012 1:34:26 PM