Panasonic SC-TM910DVD User manual

(El peso y las dimensiones son de un solo bafle)
Stereo System SC-TM910DVD Colour (S)... Silver Type
MODEL UNIT
SC-TM910DVD SA-TM910DVD Stereo
SB-TM910 Front Speaker
SB-TM910 SB-TM910
SB-PC950
SB-PS950 SB-PS950
SA-TM910DVD
SB-PC950 Center Speaker
SB-PS950 Surround
Specifications
POTENCIA DE SALIDA (AMPLIFICADOR)
Surround 110 W RCM por canal (3Ω) 1kHz, 10% DAT
Central 110 W RCM por canal (3Ω)1kHz, 10% DAT
Frontal (Alto) 110 W RCM por canal (3Ω) 1kHz, 10% DAT
(Bajo) 110 W RCM por canal (3Ω) 100Hz, 10% DAT
SC-TM910DVD
ESPECIFICACIONES POR CADA BAFLE
FRONTAL SURROUND
Bocina Super Woofer
Bocina Woofer
Bocina Tweeter
Super Tweeter
Alto 3 Ω, Bajo 3 Ω3 Ω3 Ω
CENTRAL
SB-TM960 SB-PS950 SB-PC950
20 cm
12 cm
6 cm
- - - - -
8 cm
6 cm
- - - - -
8 cm x 2
- - - - -
Piezo type
IMPEDANCIA DE ENTRADA
Dimensiones (b x h x l) 250 mm x 429 mm x 318.5 mm 140 mm x 330 mm x 155.8 mm 409 mm x 104 mm x 155.5 mm
6.2 kg aprox. 1.3 kg aprox. 1.5 kg aprox.
Peso
UNIDAD PRINCIPAL
POTENCIA DE SALIDA: 7000 W (P.M.P.O.)
310 W
127 V ca ±10% 60 Hz
250 mV
520 - 1710 kHz (paso de 10 kHz)
87.9 - 107.9 MHz (paso de 0,2 MHz)
87.5 - 108.0 MHz (paso de 0,1 MHz)
CONSUMO DE POTENCIA:
ALIMENTACION:
SENSIBILIDAD AUX:
100 mV
SENSIBILIDAD MUSIC PORT:
RANGO DE SINTONIA AM:
RANGO DE SINTONIA FM:
DIMENSIONES (b x h x l)
PESO:
SA-TM910DVD
5.4 kg aprox.
250 mm x 330 mm x 348 mm

Overall Frequency Response (+3, -6 dB) at DECK OUT
Normal 35 Hz to 14 kHz
S/N Ratio 50 dB (A weighted)
Wow and Flutter 0.18% (WRMS)
Fast Forward and Rewind Time Approx. 120 seconds with
C-60 cassette tape
nDISC SECTION
Disc played [8 cm or 12 cm]
(1) DVD (DVD-Video, DivX#1,#2 )
(2) DVD-RAM (DVD-VR, JPEG# 2,#3, MP3# 2,#4, MPEG4# 2,#5, DivX# 1,#2)
(3) DVD-R (DVD-Video, DVD-VR, JPEG# 2,#3, MP3# 2,#4, MPEG4# 2,#5,
DivX# 1,#2)
(4) DVD-R DL (DVD-Video, DVD-VR)
(5) DVD-RW (DVD-Video, DVD-VR, JPEG# 2,#3, MP3# 2,#4, MPEG4#
2,#5, DivX# 1,#2)
(6) +R/ +RW (Video)
(7) +R DL (Video)
(8) CD,CD-R/RW [CD-DA, Video CD, SVCD#6 , MP3# 2,#4, WMA# 2,#7,
JPEG# 2,#3, MPEG4# 2,#5, DivX# 1,#2, HighMAT Level 2 (Audio and
Image)]
#1Plays all versions of DivX®video (including DivX®6) with standard
playback of DivX®media files. Certified to the DivX Home Theater
Profile. GMC (Global Motion Compensation) is not supported.
#2The total combined maximum number of recognizable audio,
picture and video contents and groups: 4000 audio, picture and video
contents and 400 groups.
#3Exif Ver 2.1 JPEG Baseline files
Picture resolution: between 160 x 120 and 6144 x 4096 pixels
(Sub sampling is 4:0:0, 4:2:0, 4:2:2 or 4:4:4). Extremely long and
narrow pictures may not be displayed.
#4MPEG-1 Layer 3, MPEG-2 Layer 3
#5MPEG4 data recorded with the Panasonic SD multi cameras or
DVD video recorders.
Conforming to SD VIDEO specifications (ASF standard) / MPEG4
(Simple Profile) video system / G.726 audio system
#6Conforming to IEC62107
#7Windows Media Audio Ver. 9.0 L3
Not compatible with Multiple Bit Rate (MBR)
Pick up
Wavelength (DVD/CD) 662 nm/785 nm
Laser power (DVD/CD) CLASS 1 / CLASS 1M
Audio output (Disc)
Number of channels (FL,FR,C,SL,SR,SW),5.1ch
Audio performance (measurement at: Rec out terminal)
Frequency response (CD-Audio) 4Hzto20kHz
nVIDEO SECTION
Video system
Signal system PAL625/50, PAL525/60, NTSC
(For GC, GS & GCT only)
NTSC, PAL525/60, PAL625/50
(For GCS only)
Composite video output
Output level 1 Vp-p (75 Ω)
Terminal Pinjack(1system)
S-video output
Y output level 1 Vp-p (75 Ω)
C output level 0.3Vp-p(75Ω) (PAL)
0.286 Vp-p (75 Ω)(NTSC)
Terminal S terminal (1 system)
Component video output
[NTSC : 480p / 480i, PAL: 576p / 576i]
Y output level 1Vp-p(75Ω)
PBoutput level 0.7 Vp-p (75 Ω)
PRoutput level 0.7 Vp-p (75 Ω)
Terminal
Pin jack (Y: green, PB:blue,P
R:red)(1system)
nGENERAL
Power supply
For GC only AC 220 to 240 V, 50/60Hz
For GCS/GS/GCT only AC 110 to 127V/220 to 240 V,
50/60Hz
Power consumption 360 W
Power consumption in standby mode:
0.5 W (approximate)
Dimensions (W x H x D) 250 x 330 x 334.6 mm
Mass 5.5 kg
Operating temperature range +5to+35°C
Operating humidity range 5% to 90% RH (no condensation)
nSYSTEM
For information on speaker system, please refer to the original
Service Manual (Order No. MD0605195C3) for SB-VK950GC-S,
(Order No. MD0605194C3) for SB-PC950GC-S, (Order No.
MD0605199C3) for SB-PS950GC-S & (Order No. MD0605200C3) for
SB-WVK950GC-S..
2
S
A-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GCT
2
manual de servicio SC-TM910DVD

Notes:
1.Specifications are subject to change without notice.
Mass and dimensions are approximate.
2.Total harmonic distortion is measured by the digital spectrum
analyzer.
3
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
3
manual de servicio SC-TM910DVD

1 Safety Precautions
1.1. General Guidelines
1.When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2.After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3.After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1.Unplug the AC cord and connect a jumper between the two prongs on the plug.
2.Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to the chassis, the reading must be .
Figure 1
1.1.2. Leakage Current Hot Check
(See Figure 1)
1.Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2.Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitor, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3.Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4.Check each exposed metallic part, and measure the voltage at each point.
5.Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6.The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may
be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is out of the limits
specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to
the customer.
5
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
4
manual de servicio SC-TM910DVD

1.2. Safety Precaution for AC Power Supply Cord (For GS only)
1.3. Before Use (For GS/GCS/GCT only)
Be sure to disconnect the mains cord before adjusting the voltage selector.
Use a minus(-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will
be used. (If the power supply in your area is 117V or 127V, set to the “127V” position.)
Note that this unit will be seriously damaged if this setting is not made correctly. (There is no voltage selector for some countries,
the correct voltage is already set.)
1.4. Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C2254, C2256, C2288, C2289, C2632, C2721, C2725, C2811, C2815,
C2817, C5512, C5513, C5514, C5712, C5713, C5715, C5718, C5790, C5805, C5806, C5807, C5914, C5916, C5917, C5929,
C5930, C5971 and C5977 through a 10Ω, 5W resistor to ground.
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 110 ~ 127V, 50 / 60 Hz & AC 220 ~ 240V, 50 / 60 Hz in NO SIGNAL (vol. min, at CD mode) should
be ~500mA. [For GCS/GS/GCT only]
Current consumption at AC 220 ~ 240V, 50 / 60 Hz in NO SIGNAL (vol. min, at CD mode) should be ~500mA . [For GC only]
1.5. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
• No sound is heard when the power is turned on.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1.Turn off the power.
2.Determine the cause of the problem and correct it.
6
S
A-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GCT
5
manual de servicio SC-TM910DVD

3.Turn on the power once again after one minute.
Note :
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
7
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
6
manual de servicio SC-TM910DVD

2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1.Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2.After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminium foil, to prevent electrostatic charge build up or exposure of the assembly.
3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4.Use only an anti-static solder remover device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge to damage ES devices.
5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or
comparable conductive material).
7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8.Minimize body motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
8
S
A-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GCT
7
manual de servicio SC-TM910DVD

3 Handling Precautions for Traverse Unit
The laser diode used inside optical pickup could be destroyed due to static electricity as a potential difference is caused by
electrostatic load discharged from clothes or human body. Handling the parts carefully to avoid electrostatic destruction during
repair.
3.1. Handling Optical Pickup
1.Do not impact on optical pickup as the unit structurally uses an extremely precise technology.
2.Short-circuit the flexible cable of optical pickup remove from the circuit board using a short-circuit pin or clip in order to prevent
laser diode from electrostatic destruction (Refer to Fig. 3.1 and Fig. 3.2)
3.Do not handle flexible cables forcibly as this may cause snapping. Handle the parts carefully (Refer to Fig. 3.1)
4.A new optical pickup is equipped with an anti-static flexible cable. After replacing and connecting to the flexible board, cut the
anti-static flexible cable. (Refer to Fig. 3.1)
Fig 3.1
3.2. Replacing Precautions for Optical Pickup Unit
CD/DVD Optical Pickup
The optical pickup by which part supply was carried out attaches the short clip to the flexible board for laser diode electrostatic
discharge damage prevention. Please remove the short clip and be sure to check that the short land is open, before connecting.
(Please remove solder, when the short land short-circuits.)
3.3. Grounding for Preventing Electrostatic Destruction
1.Human body grounding
Use the anti-static wrist strap to discharge the static electricity accumulated in your body. (Refer to Fig. 3.2)
2.Work place grounding
Place a conductive material (conductive sheet) or ironboard where optical pickup is placed. (Refer to Fig. 3.2)
Note :
Keep your clothes away from optical pickup as wrist strap does not release the static electricity charged in clothes.
Fig. 3.2
9
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
8
manual de servicio SC-TM910DVD

4 Precaution of Laser Diode
Caution :
This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens.
Wavelength : 785 nm(CD)/662 nm(DVD)
Maximum output radiation power from pick up : 100 µW/VDE
Laser radiation from pick up unit is safety level, but be sure the followings:
1.Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous.
2.Do not adjust the variable resistor on the pick up unit. It was already adjusted.
3.Do not look at the focus lens using optical instruments.
4.Recommend not to look at pick up lens for a long time.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
nUse of Caution Labels
10
S
A-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GCT
9
manual de servicio SC-TM910DVD

5 Warning
5.1. Service caution based on legal restrictions
5.1.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt
the lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30
degrees C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: Tin (Sn), 96.5%, Silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
11
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
10
manual de servicio SC-TM910DVD

6 Accessories
Cable de alimentación de CA .......................... SJA168-1A
Antena interior
de FM .......................... RSA0007-L
Antena de cuadro
de AM .......................... ND1AAAA00002
Pilas para el mando a
distancia ...................... UM-3PA/T
Mando a distancia ........
KM19201-01
Plug para RCA/ Jack 3.5 ........
EUR7662YM0
Cable de video ...................... K2KA2CA00011
11
manual de servicio SC-TM910DVD

10
Guía de control: unidad principal
3
4
5
MIC VO L
MIC 1
MIC 2
OPEN
SUBW OOFER
SOUND EQ
SUPPER SOUND EQ
PHONES
OPEN
V
O
L
U
M
E
TA P E DV D / C DTUNERAUX/MUSIC P.
DEMO
RECORDDECK 1/2DISPLAY STOPREW/ /FF
1
SINGLE CHANGE
MULTI CHANGE
OPEN/CLOSE
2
3
4
5
MIC VOL
MIC 1
MIC 2
OPEN
S.WOOFER
SOUND EQ
SUPER SOUND EQ
SUPER SURROUND
SURROUND
ENHANCER
PHONES
AUX/MUSIC P.
OPEN
AC IN
V
O
L
U
M
E
TAPE DVD/CDTUNERAUX/MUSIC P.
DEMO
RECORDDECK 1/2DISPLAY STOPREW/ /FF
PHONES
Conector de diadema
Reduzca el volumen y conecte
los auriculares.
Tipo de conector de auriculares:
3.5 mm estéreo.
Evite escuchar durante largos
períodos para prevenir el daño
a la audición.
AC IN (indicador de alimentación de CA)
Este indicador se enciende cuando la unidad está
conectada a la alimentación principal de CA.
(Interruptor de modo latente/encendido)
Pulse para cambiar la unidad de encendida al modo
de espera y viceversa.
En el modo de espera, la unidad todavía consume un
poco de energía eléctrica.
BAND, TUNER
(➡ 22)
SURROUND ENHANCER
(➡ 27)
, RECORD (➡ 24, 30)
1 a 5 (botones de
reproducción directa
de discos) (➡ 9)
, MULTI CHANGE
(➡ 9)
, OPEN/CLOSE
(➡ 9)
– VOLUME + (➡12, 25)
Bandejas de discos
(➡ 9)
, TAPE (➡ 23)
, DVD/CD (➡ 8, 9, 12, 25)
, STOP (➡ 12)
DISPLAY, -DEMO
(➡ 8, 30)
SUPER SURROUND (➡ 28)
– MIC VOL + (➡ 26)
SUPER SOUND EQ (➡ 28)
Botón de apertura de
Deck 2 , OPEN
(➡ 23)
Botón de apertura de
Deck 1 , OPEN
(➡ 23)
Botón de selección
de DECK 1 (➡ 23)
, , /FF
(Omitir disco/búsqueda/
reproducción en cámara lenta,
avance rápido/rebobinado
de audiocinta, sintonización,
botones de ajuste de hora)
(➡8, 9, 23, 32)
Portacasete Deck 1
(➡ 23)
Portacasete Deck 2
(➡ 23)
Conector AUX/MUSIC PORT
(➡ 30)
, SINGLE CHANGE
(➡ 9)
MIC 1, MIC 2 (➡ 25)
AUX/MUSIC PORT (➡ 30)
SOUND EQ (➡ 27)
S.WOOFER ( ➡ 28)
Sensor de señal del
mando a distancia


, REW/
 
12
manual de servicio SC-TM910DVD

11
Guía de control: mando a distancia
(➡8, 29)
TV (➡29, 31)
Botones numéricos (➡12)
CLOCK/TIMER (➡8, 29)
PLAY/REC (➡29)
, , /REW, FF/
(➡8, 12, 22, 23, 29)
TAPE (➡23)
TUNER/AUX/MUSIC P. (➡22, 30)
TOP MENU, DIRECT
NAVIGATOR (➡14, 15)
MENU, PLAY LIST (➡12, 14)
CANCEL (➡12, 18)
DISC (➡12)
, STOP, , PAUSE (➡12)
SOUND (➡27)
S. WOOFER (➡28)
V. MUTE,
ECHO (➡26)
AUDIO (➡25)
+, –, VOLUME (➡31)
VOLUME +, –, (➡12, 22, 26)
SLEEP/A.OFF (➡29)
CH , (➡31)
, , SLOW/SEARCH
(➡12, 22)
DVD/CD (➡8, 9, 13, 25)
FUNCTIONS (➡14, 17)
, , , , ENTER
(➡8, 12, 13, 17, 20, 25)
RETURN, -SETUP
(➡8, 12, 17, 20)
DIMMER (➡30)
SURROUND ENHANCER
(➡27)
TV/AV (➡31)
PLAY MODE, CD MODE,
REPEAT (➡13, 23)
FL DISPLAY (➡12)
C.FOCUS (➡27)
MUTING (➡30)
TV
TV
TV
CH SELECT, -TEST(➡28)
 






AUX
AUX
MUSIC P.
13
manual de servicio SC-TM910DVD

7.3.1. Disc Playability
7.3. Disc Information
15
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
14
manual de servicio SC-TM910DVD

7.3.2. To Play MP3/ WMA and still Pictures (JPEG/ tiff)
16
S
A-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GCT
15
manual de servicio SC-TM910DVD

7.4. DivX VOD Content
17
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
16
manual de servicio SC-TM910DVD

8 New Features
8.1. CRS1D Mechanism Overview
18
S
A-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GCT
17
manual de servicio SC-TM910DVD

8.1.1. General Feature
• This is a five disc changer mechanism for CD/DVD. The outline figure is shown below.
• The mechanism has "CHANGE WHILE PLAY" function. It open other trays for disc exchanging while one tray is at PLAY
position performing recording or reproducing.
• The mechanism can quickly change all trays with "CHANGE ALL" function. All trays can be move to OPEN position with one
operation.
• There is no sensor to indicate presence of disc on any tray.
8.1.2. Hardware composition
• Below is the hardware components of the mechanism
Name Function
Open Switch (OPEN-SW) The switch is used to detect normal tray opening
The switch is used for detect tray being manually push/trigger when full open
Home Switch (HOME-SW) Is used to detect cam gear home position
Close Sensor (CLOSE-SENSOR) Used for normal single tray closing
Used to detect cam gear rotate to Play Driving position
Play Switch (PLAY-SW) Detect TRV clamping complete position
Stocking Switch (STOCK-SW) Detect tray completely transfer for play position to stocking position
UD Sensor (UD-SENSOR) Detect TRV vertical movement position
Top Switch (TOP-SW) Detect a default position of TRV vertical movement position
Driver IC To drive Motor
Motor Main driving source for changer
Plunger Switching the driving source from motor to:
1.Tray open/close
2. Drive tray to play/stock position and TRV vertical movement
8.1.3. Mechanism Operation
• This mechanism has the following state:
1.Driving of a tray to open/close
2.Up/down operation of a traverse performs a state changes of tray.
By using the plunger to lift/release of a switching gear, and the cam gear to lift/release the function gear the motor can be link
to several gear trains to perform various operations.
• The functions that can be perform in this mechanism are described as below:
Condition Explanation
Open current playing tray The state to change current playing disc. All tray will be open at once and current tray at PLAY position
will be expose.
Open All The state where all trays being driven to OPEN position. The disc can be taken in or out from tray to tray
by close tray one by one from top to bottom.
Stock The state where the trays are stored in STOCK position
Play The state where one of the tray 5 trays is being driven to PLAY position and clamped by traverse unit
Play & Open Tray-* The state where one of the tray is in playing position performing recording or reproducing, other trays can
be used (OPEN position) for disc exchanging without stopping the recording or reproducing process.
19
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
18
manual de servicio SC-TM910DVD

8.2. Music Port
With reference to page 31 of the operating instruction manual.
Condition Explanation
Change The state when one of the opened tray being driven from OPEN position to STOCK position and other
opened trays remain still at OPEN position.
Close All The state where all open trays will being driven from OPEN position to STOCK position, one by one from
top to bottom
Note: * represent tray number (from 1 ~ 5)
8.1.4. New CD/DVD Mechanism (CRS1D)
Note:
This service manual does not contain the following information for the mention CD/DVD Mechanism drive:
• Schematic Diagram, Block Diagram and P.C.B. layout of CD/DVD Loading P.C.B.
• Part List for individual parts of the mechanism.
• Exploded View and Parts List for individual parts of the CD/DVD Mechanism drive.
Please refer to the original service manual (Order No. MD0603065A3) for the CD/DVD Mechanism Drive CRS1D.
20
S
A-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GCT
19
manual de servicio SC-TM910DVD

9 About HighMAT
9.1. What’s HighMAT?
Consumers worldwide are using PCs to create their own collections of music, photos and even video by burning them onto CDs.
But how these collections can be experienced across different devices can be confusing to navigate, time consuming to access for
a DVD player, and be incomplete in terms of music information available to the customer.
HighMAT offers a solution to this growing consumer problem. HighMAT dramatically improves the digital media experience on
consumer electronic devices by delivering a simple, standardized approach that allows consumers who have created personal
collections of digital music, photography and video on their PC to:
>> Create a HighMAT CD or DVD which can be easily played back on consumer electronics devices such as CD and DVD players,
and car stereos.
>> Move digital media files (using recordable media such as CD-R and CD-RW) between the PC and various playback devices
such as CD and DVD players.
A new standard for creating personal media on consumer electronic devices, HighMAT enable easier and more seamless
interoperability between Windows PCs and devices designed for your living room, or the car.
9.2. Why take advantage of HighMAT?
A Problem Defined:Today, when consumers create their own digital audio, video or photo collections on CD-R or other physical
formats, there are numerous, inconsistent ways that devices read the data. For the consumer, the playback experience can be
confusing:
21
SA-VK950GC / SA-VK950GS / SA-VK950GCS / SA-VK950GC
T
20
manual de servicio SC-TM910DVD