Panasonic SCAK750 - CD STEREO SYSTEM User manual

Operating Instructions
CD Stereo System
Model No. SC-AK750
RQTV0205-1B
EEBGN
Table of contents
Caution for AC Mains Lead.....................4
Safety precautions ..................................4
Handling of the disc trays and discs.....5
Placement of speakers............................5
Getting started.........................................6
Overview of controls...............................8
Discs.........................................................9
Cassette tape – Play and record ..........12
FM/AM radio...........................................13
Timer.......................................................14
Sound adjustment .................................15
External unit...........................................15
Troubleshooting guide..........................17
Maintenance...........................................18
When moving the unit...........................18
Specifications ........................................19
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these
instructions carefully.
These operating instructions are applicable to the following
systems.
System SC-AK750
Main unit SA-AK750
Front speakers SB-AK750
Subwoofer SB-WAK750
Before connecting, operating or adjusting this product,
please read these instructions completely.
Please keep this manual for future reference.
Note:
“EB” on the packaging indicates the United Kingdom.
Operations in these instructions are described mainly using
remote control, but you can perform the operations on the
main unit if the controls are the same.
Your unit may not look exactly the same as illustrated.
SUPPLIED ACCESSORIES
SUPPLIED ACCESSORIES
Please check and identify the supplied accessories.
Use numbers indicated in parentheses when asking for
replacement parts. (As of January 2007)
1 x AC mains lead
For the United Kingdom
(K2CT3CA00004)
For Continental Europe
(K2CQ2CA00006)
For Australia and N.Z.
(K2CJ2DA00008)
1 x Remote Control
(N2QAYB000139)
2 x Remote control
batteries
1 x FM indoor antenna
For Europe
(RSA0007-L)
For Australia and N.Z.
(RSA0006-L)
1 x AM loop antenna
(N1DAAAA00001)
RQTV0205-B.indd 1RQTV0205-B.indd 1 2/22/07 7:01:51 PM2/22/07 7:01:51 PM

2
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
(Back of product)
Inside of product
Tuotteen sisällä
Produktets innside
RQTV0205-B.indd 2RQTV0205-B.indd 2 2/22/07 7:01:56 PM2/22/07 7:01:56 PM

3
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
RQTV0205-B.indd 3RQTV0205-B.indd 3 2/22/07 7:01:57 PM2/22/07 7:01:57 PM

4
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
Caution for AC Mains Lead
Placement
Set the unit up on an even surface away from direct
sunlight, high temperatures, high humidity, and excessive
vibration. These conditions can damage the cabinet and
other components, thereby shortening the unit’s service life.
Place it at least 15 cm away from wall surfaces to avoid
distortion and unwanted acoustical effects.
Do not place heavy items on the unit.
Voltage
Do not use high voltage power sources. This can overload
the unit and cause a fire.
Do not use a DC power source. Check the source
carefully when setting the unit up on a ship or other place
where DC is used.
AC mains lead protection
Ensure the AC mains lead is connected correctly and not
damaged. Poor connection and lead damage can cause fire
or electric shock. Do not pull, bend, or place heavy items on
the lead.
Grasp the plug firmly when unplugging the lead. Pulling
the AC mains lead can cause electric shock.
Do not handle the plug with wet hands. This can cause
electric shock.
Foreign matter
Do not let metal objects fall inside the unit. This can cause
electric shock or malfunction.
Do not let liquids get into the unit. This can cause electric
shock or malfunction. If this occurs, immediately disconnect
the unit from the power supply and contact your dealer.
Do not spray insecticides onto or into the unit. They
contain flammable gases which can ignite if sprayed into
the unit.
Service
Do not attempt to repair this unit by yourself. If sound is
interrupted, indicators fail to light, smoke appears, or any
other problem that is not covered in these instructions
occurs, disconnect the AC mains lead and contact your
dealer or an authorized service center. Electric shock
or damage to the unit can occur if the unit is repaired,
disassembled or reconstructed by unqualified persons.
Extend operating life by disconnecting the unit from the
power source if it is not to be used for a long time.
Safety precautions
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three pin mains
plug for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that
the replacement fuse has a rating of 5-ampere and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark mor the BSI mark oon the body
of the fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
dealer.
CAUTION!
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR
THE SOCKET OUTLET IN YOUR HOME THEN THE
FUSE SHOULD BE REMOVED AND THE PLUG CUT
OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO
ANY 13-AMPERE SOCKET.
If a new plug is to be fitted please observe the wiring code as
stated below.
If in any doubt please consult a qualified electrician.
IMPORTANT
The wires in this mains lead are coloured in accordance with
the following code:
Blue: Neutral, Brown: Live.
As these colours may not correspond with the coloured
markings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured Blue must be connected to the
terminal which is marked with the letter N or coloured Black
or Blue.
The wire which is coloured Brown must be connected to the
terminal which is marked with the letter L or coloured Brown
or Red.
WARNING: DO NOT CONNECT EITHER WIRE TO THE
EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E, BY THE EARTH SYMBOL nOR COLOURED
GREEN OR GREEN/YELLOW.
THIS PLUG IS NOT WATERPROOF—KEEP DRY.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type of AC
mains plug (figures A and B). Confirm the AC mains plug
fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
Fuse cover
Figure A Figure B
2. Replace the fuse and close or attach the fuse cover.
Fuse
(5 ampere)
Fuse
(5 ampere)
Figure A Figure B
RQTV0205-B.indd 4RQTV0205-B.indd 4 2/22/07 7:01:58 PM2/22/07 7:01:58 PM

5
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
Handling of the disc trays and discs
Not doing the following will cause damage to the unit.
Removing the mains plug
• Press [y/I] to turn off the unit and remove the mains plug only after all the displays have disappeared.
Tray caution Inserting a disc
• Always press [0, OPEN/CLOSE] to insert or remove a disc.
• Do not push or pull out the tray by hand as this will cause an
accident.
• Place the disc correctly label-up as shown in the
diagram.
• Insert one disc into the tray.
Placement of speakers
Speakers are designed identically so that no left or right
channel orientation is necessary.
Subwoofer
Front speaker
(right)
Front speaker
(left)
Main
unit
Place the
subwoofer on the
floor or a sturdy
shelf so that it will
not cause vibration.
Front speakers
You cannot take the front net off the speakers.
Use only the supplied speakers.
The combination of the main unit and speakers provide the
best sound. Using other speakers can damage the unit and
sound quality will be negatively affected.
Note:
• Keep your speakers at least 10mm away from the system for
proper ventilation.
• These speakers do not have magnetic shielding. Do not place
them near televisions, personal computers or other devices easily
influenced by magnetism.
• You can damage your speakers and shorten their useful life if you
play sound at high levels over extended periods.
• Reduce the volume in the following cases to avoid damage.
– When playing distorted sound.
– When adjusting the sound quality.
Caution
• Use the speakers only with the recommended
system. Failure to do so can damage the amplifier
and speakers, and can cause fire. Consult a qualified
service person if damage occurs or if a sudden
change in performance is apparent.
• Do not attach these speakers to walls or ceilings.
RQTV0205-B.indd 5RQTV0205-B.indd 5 2/22/07 7:01:59 PM2/22/07 7:01:59 PM

6
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
Making the connections
Making the connections
Connect the AC mains lead only after all other connections have been made.
Getting started
To household mains socket
(R) (L)
R
L
Blue (–)
Grey (+)
Red (+)
Black (–)
Red (+)
Black (–)
Connect the left (L)
side in the same way
Subwoofer
(SB-WAK750)
Connect the speaker cords.
Connect the AC mains lead.
FOR THE UNITED KINGDOM ONLY
READ THE CAUTION FOR AC MAINS LEAD ON
PAGE 4 BEFORE CONNECTION.
Insertion of connector
Even when the connector is perfectly inserted, depending
on the type of inlet used, the front part of the connector
may jut out as shown in the drawing. However there is no
problem using the unit.
For your reference
To save power when the unit is not to be used for a long
time, unplug it from the household mains socket. You will
need to reset some memory items after plugging in the
unit.
Note:
The included AC mains lead is for use with this unit only.
Do not use it with other equipment.
Connector
Appliance inlet
Connect the FM indoor antenna.
Tape the antenna where reception is best.
(
)
Adhesive
tape
Connect the AM loop antenna.
Stand the antenna
up on its base.
RQTV0205-B.indd 6RQTV0205-B.indd 6 2/22/07 7:02:03 PM2/22/07 7:02:03 PM

7
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
Optional antenna connections
Optional antenna connections
Use outdoor antenna if radio reception is poor.
Note:
Disconnect the outdoor antenna when the unit is not in use. Do not use the outdoor antenna during a lightning storm.
FM outdoor antenna AM outdoor antenna
(
)
Rear panel
of this unit
FM outdoor antenna
(not included)
75 Ωcoaxial cable
(not included)
Rear panel
of this unit
AM outdoor antenna
(not included)
AM loop antenna
(included)
5-12 m
• Disconnect the FM indoor antenna.
• The antenna should be installed by a competent
technician.
• Run a piece of vinyl wire horizontally across a window or
other convenient location.
• Leave the loop antenna connected.
Preparing the remote control
Preparing the remote control
AA/R6/LR6
■Batteries
• Insert so the poles (+ and –) match those in the remote control.
• Remove if the remote control is not going to be used for a long period of
time. Store in a cool, dark place.
• Replace if the unit does not respond to the remote control even when held
close to the front panel.
• Do not use rechargeable type batteries.
• Mishandling of batteries in the remote control can cause electrolyte
leakage, which may cause a fire.
• If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any part of
your body.
Do not:
• mix old and new batteries.
• use different types of batteries at the same time.
• heat or expose batteries to flame.
• take apart or short circuit the batteries.
• attempt to recharge alkaline or manganese batteries.
• use batteries if the covering has been peeled off.
• put heavy objects on the remote control.
• spill liquids onto the remote control.
■Use
Aim at the remote control sensor, avoiding obstacles, at a maximum range
of 7 m directly in front of the unit.
Refer to page 8 for the remote control sensor position.
DEMO function
DEMO function
7, STOP, –DEMO
When the unit is first plugged in, a demonstration of its functions may be
shown on the display.
If the demo setting is off, you can show a demonstration by selecting “DEMO
ON”.
Press and hold [7, STOP, –DEMO].
The display changes each time the button is held down.
NO DEMO (off) ÔDEMO ON (on)
While in standby mode, select “NO DEMO” to reduce power consumption.
Note:
DEMO function cannot be turned on when Dimmer is on.
RQTV0205-B.indd 7RQTV0205-B.indd 7 2/22/07 7:02:07 PM2/22/07 7:02:07 PM

8
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
Main unit
Main unit
Refer to the numbers in parentheses for page reference.
AC supply indicator [AC IN]
This indicator lights when the unit is connected
to the AC mains supply.
1Standby/on switch [y/l] (5, 18)
Press to switch the unit from on to standby mode
or vice versa. In standby mode, the unit is still
consuming a small amount of power.
Disc trays
Display panel
Disc tray open/close (5)
Disc direct play (9)
Headphone jack
Avoid listening for
prolonged periods of time
to prevent hearing damage.
Plug type: Ø 3.5 mm stereo
(not included)
Display (10, 13)
Record (12, 15 ~ 16)
Cassette deck open (12)
!Disc play/pause (9)
Demonstration, stop
(7, 12)
9Track skip/search,
tape fast-forward/
rewind, tune/preset
channel selection, time
adjustment,
(9 ~ 14, 16)
"Tape play (12)
Remote control signal sensor
Multiple discs change (9)
Single disc change (10)
7H.BASS selection (15)
5Volume control
4Tuner (FM/AM) selection (13)
3Music port selection (15)
2USB play/pause (16)
Music port jack (15)
6Preset EQ selection (15)
Cassette holder (12)
8Subwoofer selection (15)
USB port (16)
Remote control
Remote control
Buttons such as 1function the same as the controls on the main unit.
ENTER
MUSIC
PORT
SEARCH
REPEAT
SUBWOOFER MUTING
PRESET
EQ
H.BASS
MANUAL
EQ
TITLE
USB
CD
TUNER /
BAND
DISPLAY
Sleep timer (14),
Auto off
1
Program (10, 13)
Play mode (9, 13)
Enter (10 ~ 11)
Title search (11)
Disc album selection (9)
2
4"
Muting
!
Manual EQ (15)
8
5
6
Disc (9)
Delete (10 ~ 11)
Dimmer,
Play timer/record timer (14)
Numeric, characters
(9, 11, 13)
Display
Clock/timer (14)
9
Repeat (11)
7
Stop/program clear
(9 ~ 10, 16)
3
This auto off function
allows you to turn off the unit in
disc, tape or USB mode only after
left unused for 10 minutes.
• Press and hold [–AUTO OFF] to
activate the function.
• Press and hold [–AUTO OFF]
again to cancel.
• The setting is maintained even if
the unit is turned off.
To dim the display panel.
To mute the sound.
• Press the button to activate.
• Press again to cancel.
Overview of controls
RQTV0205-B.indd 8RQTV0205-B.indd 8 2/22/07 7:02:10 PM2/22/07 7:02:10 PM

9
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
Basic play
Basic play
1Press [0,OPEN/CLOSE] on the main unit to open
the tray.
The unit turns on, load a disc in the current tray with the
label facing up.
Press [0, OPEN/CLOSE] to close the tray.
2Press [6, CD] to start play.
You can also press [DISC] and then [1] ~ [5] to select
and play the other loaded discs.
23451
Current disc indicator
To Action
stop play Press [7, CLEAR] during play.
Display when in the stop mode:
Example: “MP3” indicates the disc contains MP3
fi l e s .
Total number
of albums
Total number
of tracks
pause play Press [ 6, CD] during play.
Press again to resume play.
skip album
Press [ALBUM ( or )] to select the desired
album during play or when in stop mode.
Display when selecting in stop mode (example):
Current album
Number of tracks
in current album
• This function does not work during 1-DISC
RANDOM and ALL-DISC RANDOM mode.
skip tracks Press [4, /REW ] or [¢, / FF ].
• During random play (\see right, “Play Mode
function”), you cannot skip to tracks which have
been played.
During 1-ALBUM and 1-ALBUM RANDOM mode,
track skipping can only be done within the current
album.
search
through
tracks Press and hold [4, /REW ] or [¢, / FF ]
during play or pause to search.
• During program play (\page 10), or random
play (\see right, “Play Mode function”), you can
search only within the track.
Play Mode function
You can listen to specific discs and tracks.
Preparation
Select and play your desired disc.
Press [PLAY MODE] to select the desired mode.
Mode To play
1-DISC
1 DISC
one selected disc.
ALL-DISC
ALL DISC
all loaded discs in succession from the
selected disc to the final disc.
Example: 4→5→1→2→3.
1-TRACK
1-TR
one selected track on the selected disc.
Press the numeric buttons to select the
track in the current disc.
Play starts from the selected track.
Press [ALBUM ( or )] to select the
album.
Press [4, /REW ] or [¢, / FF ],
then the numeric buttons to select the
track in the current album.
Play starts from the selected track.
1-ALBUM
1-ALB
one selected album on the selected disc.
Press [ALBUM ( or )] to select the
album.
1-DISC RANDOM
1 DISC RND
one selected disc randomly.
1- ALBUM RANDOM
1-ALB RND
all tracks in one selected album
randomly.
Press [ALBUM ( or )] to select the
album.
ALL-DISC RANDOM
ALL DISC RND
all loaded discs randomly.
When playback ends
The current play mode will be retained in memory until it is
changed even if the unit is turned off.
Note:
You cannot use program mode together with “Play Mode function”.
Changing multiple discs (MULTI CHANGE)
By main unit only
1Press [0, MULTI CHANGE] to open the trays.
2Press the button repeatedly to check and change
multiple discs.
Note:
• The tray with a disc being played will not open.
• If the player is stopped, all trays will open. To close the remaining
trays simultaneously, press [0, OPEN/CLOSE].
Discs
RQTV0205-B.indd 9RQTV0205-B.indd 9 2/22/07 7:02:16 PM2/22/07 7:02:16 PM

10
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
Discs (continued)
Changing
a single disc (SINGLE CHANGE)
a single disc (SINGLE CHANGE)
By main unit only
While one disc is playing, you can change the discs in other
trays.
1Press [0, SINGLE CHANGE].
2Press [3, 1] ~ [3, 5] to select the desired tray.
3Change the disc.
4Press [0, SINGLE CHANGE] again to close the tray.
Checking the track information
You can select a desired disc display mode.
Press [DISPLAY] during play or pause.
Elapsed play time Remaining play time
Elapsed
play time ➞Remaining play time ➞Album Name
Tag (Artist)
➞
Tag (Track)
➞
Tag (Album)
➞
Track Name
➞
➞
Note:
• When track number 25 or greater is playing, remaining play time
display shows “– –:– –”.
• When a title is longer than 9 characters, it will scroll across the
display. The scrolling will start after every 3 seconds.
• “NO TAG” is displayed if titles with tags have not been entered.
• Maximum number of displayable characters: approximately 32
• This unit can display album, track and artist name with MP3 ID3
tags (version 1.0 and 1.1).
• Titles containing text data that the unit does not support cannot
be displayed.
• ID3 is a tag embedded in MP3 track to provide information about
the track.
• Titles entered with 2-byte code cannot be displayed correctly on
this unit.
Advanced play
Advanced play
Program play
This function allows you to program up to 24 tracks.
1Press [6, CD] and then [7, CLEAR].
2Press [PROGRAM].
“PGM” appears.
3Press [DISC] and then [1] ~ [5] to select the disc.
4
Press the numeric buttons to select your desired
track.
Repeat steps 3 to 4 to program other tracks.
5Press [6, CD] to start play.
1Press [DISC] and then [1] ~ [5] to select the disc.
2Press [7, CLEAR].
3Press [PROGRAM].
4Press [ALBUM ( or )] to select your desired
album.
To select an album directly, press the numeric
buttons after pressing [ALBUM ( or )].
5Press [4, /REW ] or [¢, /FF ] to select the
track.
To select a track directly, press the numeric buttons
after pressing [4, /REW ] or [¢, /FF].
6Press [ENTER].
Repeat steps 4 to 6 to program other tracks.
7Press [6, CD] to start play.
For two-digit track, press [
h 10] once then the two digits.
For three-digit track, press [ h 10] twice then the three digits.
To Action
cancel
program mode
Press [PROGRAM] in the stop mode.
replay the
program
Press [PROGRAM] then [ 6, CD] in the stop
mode.
add to the
program Repeat steps 3 to 4 in the stop mode.
Repeat steps 4 to 6 in the stop mode.
check program
contents
Press [4, / REW] or [¢, / FF] when
“PGM” is displayed in the stop mode.
The track number, program order and disc
number are displayed:
12345
Program orderTrack number
The program order is displayed followed by the
album number and track number.
clear the last
track
Press [DEL] in the stop mode.
clear all
programmed
tracks
Press [7, CLEAR] in the stop mode. “CLEAR
ALL” is displayed. Within 5 seconds, press the
button again to clear all tracks.
Note:
• You cannot program CD-DA together with MP3 tracks.
• The program memory is cleared when you change a disc or open
the disc tray.
• You cannot program more than one disc.
RQTV0205-B.indd 10RQTV0205-B.indd 10 2/22/07 7:02:24 PM2/22/07 7:02:24 PM

11
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
Repeat play
You can repeat program play or other selected play mode.
Press [REPEAT].
“ ” is displayed.
To cancel
Press [REPEAT] again.
“ ” is cleared.
Note:
You can use repeat mode with “Program play” (\page 10) and
“Play Mode function” ( \page 9).
Advanced function (
Advanced function (
only)
only)
Album /Track title search
This function enables you to search your desired album or
track.
1Press [6, CD] and then [7, CLEAR].
2For album title search, press [TITLE SEARCH] once.
For track title search, press [TITLE SEARCH] twice.
3Press the numeric buttons repeatedly to select
your desired character then press [¢,/FF] to key
in the next character.
• You can enter up to 8 characters.
• To edit, press [4, / REW] or [¢, / FF] to revise any
characters.
• To delete, move the cursor over the character and
then press [DEL].
Numbered
Button Characters
h 10 space ! ” # $ % & ’ ( ) ∗+ , – . / : ; = ? _ `
• You can search for “<” or “>” by entering “(” or “)”.
• The special characters will be displayed as below:
Characters Main unit
display Characters Main unit display
!,
” –
# .
$ /
% :
& ;
’ =
( ?
)_
∗
`
+
• Some characters may not be displayed correctly due
to the recording format/software used.
4Press [ENTER].
Press [4, / REW] or [¢, / FF] to search for
previous or next match.
The matched title is displayed.
Album title search
Blinks to indicate album title search mode
Matched album title
Track title search
Blinks to indicate track title search mode
Matched track title
5Press [6, CD] to start play from the album/track
found.
Note:
This function does not work during any random/program mode.
NOTE on CDs
• This unit can access up to 99 tracks.
• Choose disc with this mark.
• This unit can play MP3 files and CD-DA format audio
CD-R/RW that have been finalized.
• It may not be able to play some CD-R/RW due to the condition of
the recording.
• Do not use irregularly shaped disc.
• Do not use disc with labels and stickers that are coming off or
with adhesive exuding from under labels and stickers.
• Do not attach extra labels or stickers on the disc.
• Do not write anything on the disc.
Using DualDiscs
The “CD” sides of DualDiscs do not meet the CD-DA standard so it
may not be possible to play them on this unit.
NOTE on MP3
• Files are treated as tracks and folders are treated as albums.
• This unit can access up to 999 tracks, 255 albums and 20
sessions.
• Disc must conform to ISO9660 level 1 or 2 (except for extended
formats).
•
To play in a certain order, prefix the folder and file names with
3-digits numbers in the order you want to play them.
When “NOT MP3/ERROR1” appears on the display, an
unsupported MP3 format is being played. The unit will skip that
track and play the next one.
Limitations on MP3 play
• If you have recorded MP3 on the same disc as CD-DA, only the
format recorded in the first session can be played.
• Some MP3s may not be played due to the condition of the disc or
recording.
• Recordings will not necessarily be played in the order you
recorded them.
RQTV0205-B.indd 11RQTV0205-B.indd 11 2/22/07 7:02:29 PM2/22/07 7:02:29 PM

12
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
The buttons described for “Cassette tape - Play and
record” are mainly for the main unit unless indicated
otherwise.
TAPE
Basic play
Basic play
Use normal position tapes.
High position and metal position tapes can be played, but
the unit will not be able to identify the characteristics of
these tapes.
1Press [3, TAPE] .
The unit turns on.
If a cassette was loaded, play starts automatically (One
touch play).
2Press [0,OPEN] and insert the cassette.
Insert with the side to be played facing towards you
and the exposed tape facing down. Close the holder by
hand.
3Press [3, TAPE] to start play.
To Action
stop tape playback Press [7, STOP].
fast-forward and
rewind
Press [ , REW / 4] or [ , FF/ ¢].
Note:
• Tapes exceeding 100 minutes are thin and can break or get
caught in the mechanism.
• Tape slack can get caught up in the mechanism and should be
wound up before the tape is played.
TPS (Tape Program Sensor)
TPS (Tape Program Sensor)
This function enables you to search the beginning of up to
a maximum of 9 tracks.
Press [ , REW/4] or [ , FF/¢] during play.
Play resumes from the track found.
Note:
TPS may not operate correctly in the following situations:
• If the interval between tracks is less than 4 seconds.
• If there is noise between tracks.
• If there are silent parts within tracks.
Recording
Recording
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but
this unit will not be able to record or erase them correctly.
Preparation
Wind up the source tape so recording can begin
immediately.
1Press [0,OPEN] and insert the cassette to be
recorded.
Insert with the side to be recorded facing towards you
and the exposed tape facing down.
2Select the source to be recorded.
Radio recording:
Tune in the station. (\page 13)
Disc recording:
1Insert the disc(s) you want to record.
Press [6, CD] and then [7, STOP].
2Prepare the desired disc recording mode.
To Action
record
programmed
tracks Perform steps 2 to 4 in “Program play”
(\page 10).
Perform steps 3 to 6 in “Program play”
(\page 10).
By remote control only
record
specific
discs/tracks
1) Press [DISC] and then [1] ~ [5] to select
the disc.
Ensure disc is stopped.
2) Press [PLAY MODE] to select the desired
mode (\page 9).
3)
For 1-ALBUM mode and 1-TRACK mode:
Press [ALBUM ( or )] to select the
album.
For 1-TRACK mode:
Press [4, /REW] or [¢, / FF ] to
select the track.
3Press [¶, REC] to start recording.
Other basic operations
Other basic operations
To Action
stop recording Press [7, STOP].
record on the other
side of the tape
Turn the cassette over and press [¶, REC].
erase a recorded
sound
1) Press [ 3, TAPE] and then [7, STOP].
2) Insert the recorded cassette.
3) Press [¶, REC].
Your attention is drawn to the fact that recording pre-
recorded tapes or discs or other published or broadcast
material may infringe copyright laws.
Note:
Changes to volume and sound adjustments quality do not affect
recording.
Erasure prevention
Erasure prevention
The illustration shows how to remove the tabs to prevent
recording. To record on the tape again, cover as shown.
Side A
Tab for side ATab for side B
To re-record
Normal cassette
Adhesive tape
Cassette tape – Play and record
RQTV0205-B.indd 12RQTV0205-B.indd 12 2/22/07 7:02:36 PM2/22/07 7:02:36 PM

13
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
FM/AM radio
TUNER /
BAND
Manual tuning
Manual tuning
1Press [TUNER/BAND] to select “FM” or “AM”.
2Press [PLAY MODE] to select “MANUAL”.
3Press [4, /REW] or [¢, /FF ] to select the
frequency of the required station.
“” is displayed when a stereo FM broadcast is being
received.
To tune automatically
Press and hold [4, / REW ] or [¢, / FF ] until the
frequency starts changing rapidly. The unit begins auto
tuning, stopping when it finds a station.
• Auto tuning may be interrupted when there is excessive
interference.
• To cancel auto tuning, press [4, / REW ] or
[¢, / FF ] once again.
To improve FM sound quality
Press and hold [PLAY MODE] to display “MONO”.
To cancel
Press and hold [PLAY MODE] again until “MONO”
disappears.
• MONO is also cancelled if the frequency is changed.
• Turn off “MONO” for normal listening.
RDS broadcasting (For Europe)
This unit can display the text data transmitted by the radio
data system (RDS) available in some areas.
If the station you are listening to is transmitting RDS
signals, “RDS” will light up on the display.
Press [DISPLAY] to display:
Station name
➞ Program Type ➞Frequency display
(PS) (PTY)
Program type displays
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M-O-R- M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL A
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATIONAL
OLDIES
FOLK M
DOCUMENT
TEST
ALARM
M-O-R- M = “Middle-of-the-Road music”
Note:
RDS displays may not be available if reception is poor.
TUNER /
BAND
Memory preset
Memory preset
20 FM and 15 AM stations can be preset.
Preparation
Press [TUNER /BAND] to select “FM” or “AM”.
Automatic presetting
1Tune to the frequency where presetting is to begin.
2Press and hold [PROGRAM] to start presetting.
The tuner presets all the stations it can receive into the
channels in ascending order. When finished, the last station
memorized is tuned in.
Manual presetting
1Press [PLAY MODE] to select “MANUAL”.
2
Press [4, /REW] or [¢, / FF] to tune to the
required station.
3Press [PROGRAM].
4Press the numeric buttons to select a channel.
For channels 10 to 20 press [ h 10], then the two digits.
The station occupying a channel is erased if another
station is preset to that channel.
Selecting a preset station
Press the numeric buttons to select the channel.
OR
1Press [PLAY MODE] to select “PRESET”.
2Press
[4, /REW] or [¢, /FF ] to select the
channel.
RQTV0205-B.indd 13RQTV0205-B.indd 13 2/22/07 7:02:41 PM2/22/07 7:02:41 PM

14
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
Setting the clock
Setting the clock
This is a 24-hour clock.
1Press and hold [
– CLOCK/TIMER] to select
“CLOCK”.
Each time you press the button:
CLOCK ˚PLAY
Original display
˚REC
2(Within 8 seconds or so )
Press [4, /REW] or [¢, /FF] to set the time.
3Press and hold [
– CLOCK/TIMER] to finish setting
the time.
Displaying the clock
Press and hold [ – CLOCK / TIMER] once when the unit is on or
in standby mode.
The time is displayed for a few seconds.
Note:
Reset the clock regularly to maintain accuracy.
Using the play or record timer
Using the play or record timer
You can set the timer to come on at a certain time to wake
you up (play timer) or to record from the radio or the external
equipment (record timer).
Play timer and record timer cannot be used together.
Turn the unit on and set the clock.
Timer Action
Play timer Prepare the music source you want to listen to;
cassette, disc number (1 ~ 5), radio or other
external equipments, and set the volume.
Record
timer
Check the cassette’s erasure prevention tabs
(\page 11), insert the cassette and tune to the
radio station (\page 12) or select the external
equipment (\page 15 ~ 16).
1
Press and hold [–CLOCK/TIMER] to select the timer
function.
Each time you press the button:
➞
CLOCK ˚PLAY
Original display
˚REC
➞
˚PLAY : to set the play timer
˚REC : to set the record timer
(Proceed to the next step within 8 seconds )
2Press [4, /REW] or [¢, /FF] to set the
starting time.
Play timer indicator
Start time
Record timer indicator
1
3Press and hold [
– CLOCK/TIMER] to confirm.
4Repeat steps 2 to 3 to set the finishing time.
1
Finish time
To activate the timer
5
Press and hold [–˚PLAY/REC] to turn on your desired
timer.
˚PLAY
no display (off)
˚REC
6Press [y] to turn off the unit.
The unit must be off for the timers to operate.
Other basic operations
Other basic operations
To Action
change the
settings
Repeat steps 1 to 4 and 6 (\see left and
above).
change the
source or
volume
1) Press and hold [– ˚PLAY/REC] to clear the
timer indicator from the display.
2) Make changes to the source or volume.
3) Perform steps 5 to 6 (\see above).
check the
settings
Press and hold [– CLOCK/TIMER] repeatedly
to select ˚PLAY or ˚REC.
cancel Press and hold [– ˚PLAY/REC] to clear the
timer indicators from the display.
If you use the unit after the timers are set
After using, check that the correct tape/disc are loaded
before turning the unit off.
Note:
• The play timer will start at the preset time with volume increasing
gradually to preset level.
• The record timer will start 30 seconds before the set time with the
volume muted.
• The timer comes on at the set time every day if the timer is on.
• The unit must be in the standby mode for the timer to function.
• If you turn the unit off and on again while a timer is functioning,
the finish time setting will not be activated.
• If MUSIC PORT is selected as the source when the timer comes on,
the system turns on and engages MUSIC PORT as the source. If
you wish to playback or record from the portable audio equipment,
just activate the equipment’s play mode and increase the volume.
(See the portable audio equipment’s instruction manual.)
Using the sleep timer
Using the sleep timer
This function enables you to turn off the unit automatically
after the set time.
Press [SLEEP] to select your desired time.
SLEEP 30 SLEEP 60 SLEEP 90
SLEEP OFF SLEEP 120
Sleep timer indicator
To cancel
Press [SLEEP] to select “SLEEP OFF”.
Changing the remaining time
Press [SLEEP] to show the remaining time and press
[SLEEP] again to select your desired time.
Note:
• The play and sleep timer or the record and sleep timer can be
used together.
• The sleep timer always has priority. Be sure not to overlap timer
settings.
• The sleep timer turns off when you perform the record function.
Timer
RQTV0205-B.indd 14RQTV0205-B.indd 14 2/22/07 7:02:46 PM2/22/07 7:02:46 PM

15
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
Selecting sound effects
Selecting sound effects
Preset EQ
Press [PRESET EQ] repeatedly to select your desired
setting.
➞
HEAVY SOFT CLEAR
➞VOCAL ➞
FLAT (off) HALL LIVE
➞➞
DISCO
➞
Setting Effect
HEAVY Adds punch to rock
SOFT For background music
CLEAR Clarifies higher frequencies
VOCAL Adds gloss to vocal
DISCO Produces sound with the same kind of lengthy
reverberations heard at a disco
LIVE Makes vocals more alive
HALL Adds an expansiveness to the sound to produce
the atmosphere of a great concert hall
FLAT No effect
Manual EQ
MANUAL
1
Press [MANUAL EQ] repeatedly to select your desired
setting.
➞
BASS MID TREBLE
➞
Setting Effect
BASS For lower pitch sound
MID For middle pitch sound
TREBLE For higher pitch sound
2Press [4, /REW] or [¢, /FF] to adjust the
level.
Note:
• The level of the pitch is between -3 to +3.
• The changes you make are stored and automatically recalled the
next time you select “MANUAL EQ”.
Enhancing the bass sound
Enhancing the bass sound
You can enhance low-frequency sound so that heavy bass
sound can be heard clearly, even if the acoustics of your
room are not optimal.
To activate
Press [H.BASS].
To cancel
Press [H.BASS] again.
Note:
The actual effect depends on the disc.
Boosting the subwoofer
Boosting the subwoofer
Press [SUBWOOFER] repeatedly to select your desired
setting.
➞
MID (medium)
(off)
MAX (high)
Note:
This function is not applicable when a headphone is connected.
Sound adjustment External unit
Connecting to a portable audio equipment
Connecting to a portable audio equipment
This feature enables you to enjoy music from a portable
audio equipment.
Note:
All peripheral components and cables are sold separately.
Audio cord
(not included)
Portable audio equipment
(not included)
Playing from a portable audio
Playing from a portable audio
equipment
equipment
Switch off the equalizer function (if there is any) of the
portable audio equipment before you plug into the MUSIC
PORT jack. Otherwise, sound from the speaker may be
distorted.
1Plug the audio cord into the MUSIC PORT jack and
press [MUSIC PORT].
2Play the portable audio equipment. (See the portable
audio equipment’s instruction manual.)
Recording from a portable audio
Recording from a portable audio
equipment
equipment
1
Press [MUSIC PORT ].
2Play the portable audio equipment.
3Press [¶, REC] on the main unit to start recording.
RQTV0205-B.indd 15RQTV0205-B.indd 15 2/22/07 7:02:48 PM2/22/07 7:02:48 PM

16
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
External unit (continued)
Connecting and playing a USB mass
Connecting and playing a USB mass
storage class device
storage class device
The USB connectivity enables you to connect and play
MP3 tracks from USB mass storage class. Typically, USB
memory devices. (Bulk only transfer)
Preparation
Before connecting any USB mass storage device to the unit,
ensure that the data stored therein has been backed up.
It is not recommended to use a USB extension cable. The
USB device is not recognised by this unit.
USB enabled device
(not included)
It is not recommended
to use a USB extension
cable. The device
connected via the cable
will not be recognised by
this unit.
1
Reduce the volume and connect the USB mass storage
device.
2Press [6, USB] to start play.
To Action
pause play
USB
Press [6, USB].
Press again to resume play.
stop play Press [7, CLEAR].
“RESUME” is displayed. The position is
memorized.
Press [6, USB] to resume.
Press [7, CLEAR] again to clear the position.
skip tracks Press [4, / REW] or [¢, / FF].
skip album Press [ALBUM ( or )] in the play mode.
Press [ALBUM ( or )] once and then
the numeric buttons in the stop mode.
For other operating functions, they are similar as those
described in “Discs” (\page 9 ~ 11).
Recording from a USB mass
Recording from a USB mass
storage class device
storage class device
1
Press [4, /REW ] or [¢, /FF] to select the
desired track for recording.
2Press [¶, REC] on the main unit to start recording.
Compatible devices
Compatible devices
Devices which are defined as USB mass storage class:
• USB devices that support bulk only transfer.
• USB devices that support USB 2.0 full speed.
Supported format
Supported format
Files must have the extension “.mp3” or “.MP3”.
Note:
• CBI (Control/Bulk/Interrupt) is not supported.
• A device using NTFS file system is not supported [Only FAT 16/32
(File Allocation Table 16/32) file system is supported].
• Depending on the sector size, some files may not work.
• This unit can access up to 255 albums (including blank folders)
and 2500 tracks.
• The maximum number of tracks in a folder are 999 tracks.
• Only one memory card will be selected when connecting a
multiport USB card reader. Typically the first memory card
inserted.
• Disconnect the USB card reader from the unit when you remove
the memory card. Failure to do so may cause malfunction to the
device.
• When you connect your digital audio player to the USB port,
it charges all the time except in standby mode or during tape
recording.
MUSIC PORT
Changing the main unit and
Changing the main unit and
remote control mode
remote control mode
The remote control and main unit are factory-set to
“REMOTE 1” mode.
If your remote control affects other equipment during
operation, you can switch to operate in “REMOTE 2” mode.
To switch to “REMOTE 2” mode
1
While pressing and holding [MUSIC PORT] on the main
unit
Press and hold [2] until “REMOTE 2” appears on
the main unit display.
2Press and hold [ENTER] and [2] for at least 2
seconds.
The main unit and remote control are now set to
operate in “REMOTE 2” mode.
To return to “REMOTE 1” mode
Perform steps 1 and 2 above but use [1] instead of [2] for
both steps. (“REMOTE 1” appears on the main unit during
step 1.)
The remote control cannot work with the main unit if
their modes are different.
“REMOTE 1” or “REMOTE 2” appears on the main unit
display when you operate the remote control.*
*If “REMOTE 1” appears (The main unit is in “REMOTE 1”
mode.)
Press and hold [ENTER] and [1] on the remote control for
at least 2 seconds.
If “REMOTE 2” appears (The main unit is in “REMOTE 2”
mode.)
Press and hold [ENTER] and [2] on the remote control for
at least 2 seconds.
RQTV0205-B.indd 16RQTV0205-B.indd 16 2/22/07 7:02:53 PM2/22/07 7:02:53 PM

17
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
Troubleshooting guide
Before requesting service, make the checks below. If you can’t fix the system as described below, or if something
not listed here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or
contact your dealer.
Reference pages are shown as black circled numbers 4.
Common problems
Although the unit is in standby
mode, the display lights up and
changes continuously.
Turn off the demo function. 7
If you set the clock, demo function will be turned off automatically. %
No sound.
Sound stops. Turn the volume up.
Switch off the unit, determine and correct the cause, then switch the unit on.
Causes include straining of the speakers through excessive volume or power,
and using the unit in a hot environment.
Sound is unfixed, reversed or
comes from one speaker only. Check the speaker connections. 6
Humming heard during play. An AC mains lead or fluorescent light is near the cables. Keep other appliances
and cords away from this unit’s cables.
“ERROR” is displayed. Incorrect operation performed. Read the instructions and try again.
“– –:– –” appears on the display at
standby mode. You plugged the AC mains lead in for the first time or there was a power failure
recently.
Set the time. %
“F61” is displayed. Check and correct the speaker cords connection. 6
If this does not fix the problem, there is a power supply problem. Consult the
dealer.
Listening to the radio
Noise is heard.
The stereo indicator flickers or
doesn’t light.
Sound is distorted.
Use an outdoor antenna. 7
A beat sound is heard. Turn the TV off or separate it from the unit.
A low hum is heard during AM
broadcast. Separate the antenna from other cables and cords.
When there is a television set nearby
The picture on the TV disappears
or stripes appear on the screen. The location and orientation of the antenna are incorrect. If you are using an
indoor antenna, change to an outdoor antenna.
The TV antenna wire is too close to the unit. Separate the antenna wire of the TV
set from the unit.
Using the cassette deck
Poor sound quality. Clean the heads. ~
Recording is not possible. If the erasure prevention tabs have been removed, cover the holes with adhesive
tape. #
Playing discs
The display is wrong or play won’t
start. The disc may be upside down. 5
Wipe the disc.
Replace the disc if it is scratched, warped, or non-standard.
Condensation may have formed inside the unit due to a sudden change in
temperature. Wait for about an hour for it to clear and try again.
The total number of tracks
displayed differs each time the
same disc is inserted.
Unusual sound is heard.
The disc may be scratched, or its data may be defective. Replace the disc.
CD-RW cannot be read. The disc was incompletely formatted. Use the recording equipment to fully
format the disc before recording.
“VBR–” is displayed instead of the
remaining play time. The unit cannot display the remaining play time for variable bit rate (VBR) tracks.
RQTV0205-B.indd 17RQTV0205-B.indd 17 2/22/07 7:02:58 PM2/22/07 7:02:58 PM

18
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK ESPAÑOL
Troubleshooting guide (continued)
Disc trays
Disc tray(s) cannot open.
“CHGR ERR ” is displayed. Press [y/I] to release the jammed tray(s) as the unit will switch off. Switch it on
again and the tray(s) will initialize to the previous tray(s) condition.
If this still does not fix the problem, please consult the dealer.
Remote control
Remote control doesn’t work. Check that the batteries are inserted correctly. 7
Replace the batteries if they are worn.
USB
No response when [¶, REC] button
is pressed. Disconnect the USB device and then reconnect it back. Alternatively, turn the
unit off and then back on.
The USB drive or its contents
cannot be read. The USB drive format or its contents is/are not campatible with the system. (
The USB host function of this product may not work with some USB devices.
USB devices with storage capacity of more than 8 gigabytes may not work in
some instances.
Slow operation of the USB flash
drive. Large file size or high memory USB flash drive takes longer time to read.
“USB OVER CURRENT ERROR” The USB mass storage device rating exceeds 500mA. Disconnect the USB
device. Turn the unit off and then back on.
“NO PLAY” Check the content.
Only MP3 format files can be played.
Memory reset (Initialization)
When the following situations occur, refer to the instructions below to reset the memory:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
To reset memory
1 Disconnect the AC mains lead. (Wait at least 3 minutes before proceeding to step 2)
2 While pressing and holding down [y/I] on the main unit, reconnect the AC mains lead.
“– – – – – – – – –” appears on the display.
3 Release [y/I].
All the settings are returned to the factory preset.
You will need to reset the memory items.
Maintenance
If the surfaces are dirty
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this
unit.
• Before using chemically treated cloth, read the
instructions that came with the cloth carefully.
For a cleaner crisper sound (cassette deck)
For a cleaner crisper sound (cassette deck)
Clean the heads regularly to assure good quality playback
and recording. Use a cleaning tape (not included).
When moving the unit
1
Remove all discs.
2Press [y/I] to turn the unit off.
3Disconnect the AC mains lead.
RQTV0205-B.indd 18RQTV0205-B.indd 18 2/22/07 7:02:59 PM2/22/07 7:02:59 PM

19
RQT8043
RQTV0205 LANG - 5 LANG - 4 FRANÇAIS DANSK DEUTSCH
Specifications
AMPLIFIER SECTION
RMS output power
THD 10%, both channels driven
1 kHz
(Low channel) 110 W per channel (3 Ω)
10 kHz
(High channel) 110 W per channel (3 Ω)
60 Hz
(Subwoofer channel) 220 W per channel (6 Ω)
Total output power 660 W
FM/AM TUNER, TERMINALS SECTION
Preset station FM 20 stations
AM 15 stations
Frequency Modulation (FM)
Frequency range 87.50 to 108.00 MHz (50 kHz steps)
Sensitivity 4.0 µV (IHF)
S/N 26
dB 2.2 µV
Antenna terminal(s) 75 Ω(unbalanced)
Amplitude Modulation (AM)
Frequency range 522 to 1629 kHz (9 kHz steps)
Sensitivity
S/N 20 dB (at 999 kHz) 560 µV/m
Music Port input jack
Terminal Stereo, 3.5 mm jack
Sensitivity 100 mV, 4.7 kΩ
Phone jack
Terminal Stereo, 3.5 mm jack
CASSETTE DECK SECTION
Track system 4 track, 2 channel
Heads
Record/playback Solid permalloy head
Erasure Double gap ferrite head
Motor DC servo motor
Recording system AC bias 100
kHz
Erase system AC erase 100
kHz
Tape speed 4.8
cm/s
Overall frequency response (+3 dB, –6 dB) at DECK OUT
NORMAL 35 Hz to 14 kHz
S/N Ratio 50 dB (A weighted)
Wow and flutter 0.18% (WRMS)
Fast forward and rewind time Approx. 120 seconds with
C-60 cassette tape
DISC SECTION
Disc played [8 cm or 12 cm]
(1) CD-Audio (CD-DA)
(2) CD-R/RW (CD-DA, MP3 *formatted disc)
(3) MP3
*
*MPEG-1 Layer 3, MPEG-2 Layer 3
Bit rate
MP3 32 kbps to 320 kbps
Sampling frequency
MP3 32 kHz, 44.1 kHz, 48 kHz
CD-DA 44.1 kHz
Decoding 16 bit linear
Digital filter 8 fs
D/A converter MASH (1 bit DAC)
Pick up
Wavelength 780 nm
Beam Source Semiconductor laser
(For Norge)
Bølgelengde 780
nm
Laserstyrke Ingen farlig stråling sendes ut
Audio output (Disc)
Number of channels 2(Stereo) (FL, FR)
USB SECTION
Playable USB Storage Media
1) HDD
2) USB MP3 Player/Digital Audio Player
3) USB Thumbdrives
Supported audio file format
MP3 bit rate
USB memory port
Maximum current 500 mA
Bit rate
MP3 32 kbps to 320 kbps
Sampling frequency
MP3 32 kHz, 44.1 kHz, 48 kHz
Audio output (MP3)
Number of channels 2 channels
Frequency response (MP3) 20 Hz to 20 kHz (0+/-1.0 dB)
S/N Ratio
USB unit out 85 dB
SPEAKER SECTION
Front speakers SB-AK750
Type 3 way, 3 speaker system (Bass reflex)
Speaker(s)
Woofer 16 cm cone type
Tweeter 6
cm cone type
Super tweeter Piezo type
Impedance
HIGH 3 Ω
LOW 3 Ω
Input power (IEC)
HIGH 110 W (Max)
LOW 110 W (Max)
Output sound pressure level 87 dB/W (1.0 m)
Cross over frequency 2 kHz, 10 kHz
Frequency range 30 Hz to 24 kHz (–16 dB)
31 Hz to 21 kHz (–10 dB)
Dimensions (WxHxD) 232 x 373 x 226 mm
Mass 3.4 kg
Subwoofer SB-WAK750
Type 1 way, 1 speaker system (Bass reflex)
Speaker(s)
Subwoofer 16 cm cone type
Impedance 6 Ω
Input power (IEC) 220
W (Max)
Output sound pressure level 80 dB/W (1.0 m)
Frequency range 31 Hz to 220 Hz (–16 dB)
34 Hz to 180 Hz (–10 dB)
Dimensions (WxHxD) 249 x 330 x 256 mm
Mass 3.9 kg
GENERAL
Power supply
For continental Europe AC 230 V, 50 Hz
For the United Kingdom, Australia and N.Z
AC 230 to AC 240 V, 50 Hz
Power consumption 139 W
Dimensions (WxHxD) 250 x 330 x 323 mm
Mass 7.1 kg
Operating temperature range +5 to +35 °C
Operating humidity range 5 to 90 % RH (no condensation)
Power consumption in standby mode: 0.5 W (approx.)
Note:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
3. The labels “HIGH” and “LOW” on the rear of the speakers refer to
High frequency and Low frequency.
RQTV0205-B.indd 19RQTV0205-B.indd 19 2/22/07 7:03:00 PM2/22/07 7:03:00 PM

Matsushita Electric Industrial Co., Ltd.
Web Site: http://panasonic.net RQTV0205-1B
L0207TK1027
En
RQTV0205-B.indd 20RQTV0205-B.indd 20 2/22/07 7:03:01 PM2/22/07 7:03:01 PM