Panasonic AWHB605 - MULTI CONTROL HUB User manual

Before attempting to connect, operate or adjust this product, please
read these instructions completely.
POWER
OFF ON
Multi Control Hub AW–
Multi Control Hub
Model AW- P

32
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (service)
instructions in the literature accompanying the appliance.
indicates safety information.
FCC Note:
This device complies with Part 15 of the FCC Rules. To assure continued
compliance follow the attached installation instructions and do not make any
unauthorized modifications.
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
CAUTION:
Do not install or place this unit in a bookcase, built-in cabinet or any
other confined space in order to maintain adequate ventilation. Ensure
that curtains and any other materials do not obstruct the ventilation to
prevent risk of electric shock or fire hazard due to overheating.
WARNING:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
OKeep the temperature inside the rack to between 14°F to 113°F
(–10°C to 45°C).

54
For Your Safety
OUse the dedicated AC adapter (AW-PS505) to supply power to the multi control hub.
OHandle with care.
The multi control hub may malfunction if it is dropped or exposed to strong shocks.
OUse within a temperature range of 14°F to 113°F (–10°C to +45°C).
Using the multi control hub in environments colder than 14°F (–10°C) or hotter than
113°F (+45°C) could have a damaging effect on the internal components.
OConnect and disconnect cables only when the power is turned off.
Make sure to turn the power to the multi control hub off before connecting or
disconnecting cables.
OAvoid using the multi control hub outdoors.
OPlace the multi control hub a minimum of 1 meter away from monitor video screens.
OCleaning
Unplug the multi control hub and wipe it clean using a dry cloth. For dirt that cannot be
removed in this manner, moisten a cloth with kitchen detergent, wring it out thoroughly,
and then wipe gently.
• Never use volatile chemicals such as benzene or paint thinner to clean the multi
control hub.
• Before using chemically treated cloths to clean the multi control hub, read their
instructions and precautions thoroughly.
Accessories
OPriority switchboxes: 5
ORack mounting brackets: 12
OMounting screws: 24
Overview
OThe AW-HB605 multi control hub combines with a system such as the Panasonic AW-
PH300 series indoor pan/tilt head or AW-PH600 series outdoor pan/tilt head to support
the connection of between one and five control panels (AW-RP501, AW-RP301, AW-
RP305) to a single camera and pan/tilt head. Any of the connected control panels may
then be used to control the camera and pan/tilt head (the AW-RP301 and AW-RP305
can control the pan/tilt head only).
In addition, by adding the AW-HB505 multi port hub and AW-RP505 multi hybrid control
panel, it is possible to construct a system in which between one and five multi hybrid
control panels may be used to control between one and five cameras and pan/tilt heads.
OWhen coaxial cable/s (5C-2V) and 10BASE-T (UTP category 5) straight cable/s
(10BASE-T cable only for the AW-RP301 and AW-RP305) are used to make
connections, the distance between the cameras and pan/tilt heads and the control
panels can be extended up to a maximum of 500 meters.
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . 4
Accessories . . . . . . . . . . . . . . . . . . . . . . 4
For Your Safety. . . . . . . . . . . . . . . . . . . . 5
Controls and Their Functions . . . . . . . . 6
$Front Panel. . . . . . . . . . . . . . . . . . . . 6
$Rear Panel . . . . . . . . . . . . . . . . . . . . 7
$Priority Switchbox. . . . . . . . . . . . . . 10
System Connections . . . . . . . . . . . . . . 11
Operations. . . . . . . . . . . . . . . . . . . . . . . 17
Rack Mounting Example . . . . . . . . . . . 18
$Rack Mounting Procedure . . . . . . . 18
Specifications . . . . . . . . . . . . . . . . . . . . 19

76
Controls and Their Functions
PREVIEW OUT
CAM CONT IN
5
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
4
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
TO CONTROL PANEL TO PAN/TILT HEAD HUB
CAM CONT IN
3
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
2
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
1
PAN/TILT
CONTROL IN
BLACK
BURST OUT
BLACK
BURST
OUT
PREVIEW IN
CAM CONT OUT
PAN/TILT
CONTROL OUT
+-
DC12V IN
9
8
45
7
;
:6 3
3
DC +12 V Input Connector [DC12 V IN]
(4-pin Cannon Connector)
Connect the AW-PS505 AC adapter
(sold separately) to this connector.
4Pan/Tilt Head Control Signal Output
Connector [TO PAN/TILT HEAD HUB
PAN/TILT CONTROL OUT] (RJ-45 8-
pin Modular Jack)
Connect this connector to the control
signal input connector [P/T CONTROL
IN] of the AW-PH300 or AW-PH600
pan/tilt head, or to the pan/tilt control
signal input connector [TO CONTROL
PANEL PAN/TILT CONTROL IN] of the
AW-HB505 multi port hub using a
10BASE-T (UTP category 5) straight
cable.
5Preview Video Signal Input
Connector [TO PAN/TILT HEAD HUB
PREVIEW IN] (BNC Connector)
Connect this connector to the video
signal output connector [VIDEO OUT] of
the pan/tilt head, or to the preview video
signal output connector [TO CONTROL
PANEL PREVIEW OUT] of the multi
port hub using a coaxial cable (5C-2V
equivalent).
<Note>
In a system incorporating the AW-
RP301 or AW-RP305, the control panel
is not equipped with a video signal cable
compensation circuit. It may therefore
be necessary to use a separate cable
compensation device in some cases.
$Rear Panel
Controls and Their Functions
$Front Panel
1Power Indicator LED [POWER]
This indicator lights (red) when the
power switch 2is at the ON position. It
is dark when the power switch 2is at
the OFF position.
2Power Switch [POWER ON/OFF]
Placing this switch at the ON position
when the AC adapter is connected and
turned on supplies power to the multi
control hub (power indicator LED lights).
Placing it at the OFF position cuts off
the power.
<Note>
This switch must be at the ON position
in order to control the camera and
pan/tilt head from each control panel.
POWER
OFF ON
1
2
Multi Control Hub AW–

98
Controls and Their Functions
:Camera Control Signal Input
Connector [TO CONTROL PANEL
CAM CONT IN] (BNC Connector)
Connect this connector to the camera
control signal output connector [TO
CAMERA PAN/TILT HEAD CAMERA
CONTROL OUT] of the hybrid control
panel (AW-RP501), or to the camera
control signal output connector [TO
CAMERA PAN/TILT HEAD CAMERA
CONTROL OUT] of the multi hybrid
control panel (AW-RP505) using a
coaxial cable (5C-2V equivalent).
If the system incorporates a pan/tilt
control panel (AW-RP301) or multi
pan/tilt control panel (AW-RP305), the
control panel is not equipped with a
camera control output connector. In this
case, this connector should be left
unconnected.
;Black Burst Output [BLACK BURST
OUT] (BNC Connector)
This is the output jack for the reference
signal generator built into the multi
control hub. This signal may be used as
the reference signal for peripheral
equipment that uses external
synchronization.
Controls and Their Functions
6Black Burst Output [TO PAN/TILT
HEAD HUB BLACK BURST OUT]
(BNC Connector)
This is the output jack for the reference
signal generator built into the multi
control hub. This signal may be used as
the reference signal if the camera uses
external synchronization.
Connect this connector to the G/L signal
input connector [G/L IN] of the pan/tilt
head, or to the G/L signal input
connector [TO CONTROL PANEL G/L
IN] of the multi port hub using a coaxial
cable (5C-2V equivalent).
7Camera Control Output Connector
[TO PAN/TILT HEAD HUB CAM CONT
OUT] (BNC Connector)
Connect this connector to the camera
control signal input connector [CAMERA
CONTROL IN] of the pan/tilt head, or to
the camera control signal input
connector [TO CONTROL PANEL
CAMERA CONTROL IN] of the multi
port hub using a coaxial cable (5C-2V
equivalent).
8Pan/Tilt Head Control Signal Input
Connector [TO CONTROL PANEL
PAN/TILT CONTROL IN] (RJ-45 8-pin
Modular Jack)
Connect this connector to the control
panel pan/tilt control signal output
connector [PAN/TILT CONTROL OUT]
of the control panel using a 10BASE-T
(UTP category 5) straight cable.
9Preview Video Signal Output
Connector [TO CONTROL PANEL
PREVIEW OUT] (BNC Connector)
Connect this connector to the video
input connector [TO CAMERA
PAN/TILT HEAD VIDEO IN] of the
hybrid control panel (AW-RP501), or to
the preview video input connector
[PREVIEW IN] of the multi hybrid control
panel (AW-RP505) using a coaxial cable
(5C-2V equivalent).
If the system incorporates a pan/tilt
control panel (AW-RP301) or multi
pan/tilt control panel (AW-RP305), the
control panel is not equipped with a
video input connector. If necessary, the
output from the preview video signal
output connector may be connected to a
monitor video screen, VCR, or the like
via a cable compensation device.

1110
System Connections (Indoor Pan/tilt Head System)
OTurn off the power to all pieces of
equipment before making any
connections.
OFor the control panel, use the AC
adapter model AW-PS301 (sold
separately), for the multi port hub and
multi control hub, the AC adapter model
AW-PS505 (sold separately), and for the
pan/tilt head AC adapter model, the AW-
PS300 (sold separately).
OUse an AW-PH300 series pan/tilt head
and a camera from the convertible
camera series.
Use camera cable AW-CA50 T15 (sold
separately) to make connections
between the pan/tilt head and camera.
OConnect the pan/tilt head (AW-PH300)
to its AC adapter (AW-PS300) using a
DC power cord (cable conforming to the
Electrical Equipment Handling Law and
with a nominal cross-sectional area of
1.25 mm2or more, to be obtained
locally). The maximum cable distance
between the pan/tilt head and its AC
adapter is 30 meters.
OConnect the multi control hub to its AC
adapter (AW-PS505).
OConnect the multi port hub to its AC
adapter (AW-PS505).
OConnect the control panel (AW-RP301,
AW-RP305, AW-RP501, AW-RP505) to
its AC adapter (AW-PS301). Use a cord
clamper to secure the DC cord of the
AC adapter and prevent the DC plug
from coming loose accidentally.
OConnect the pan/tilt head and the
convertible camera using the AW-CA50
T15 camera cable.
OConnect the electric zoom lens iris
control cable to the camera and the
remote (zoom and focus control) cable
to the pan/tilt head.
Cord clamper
Control panel AC adapter:
AW-PS301
DC cord
Remote (zoom/focus
control) cable
Iris control cable
To lens interface
connector
To iris connector
Controls and Their Functions
<Priority Switchbox Contacts
(Terminal Panel)
These are the output contacts of the
priority switchbox. They should be
connected to the TALLY terminals on
the control panel. These terminals are
not polarized. Make connections using
cable conforming to the Electrical
Equipment Handling Law and with a
nominal cross-sectional area of 0.128
mm2(wire number AWG26) or more.
The maximum cable length (distance
between priority switchbox and control
panel) is 10 meters.
The connection terminals differ depending
on the control panel model. The correct
connection terminals are listed below.
AW-RP301:
TALLY HOT and GND terminals.
AW-RP305:
Any of terminals TALLY 1 through
TALLY 5 and the GND terminal. (Make
sure that the pan/tilt head control
connector number to which the AW-
HB605 is connected and the TALLY
terminal number to which the priority
switchbox is connected match.)
Also, if the pan/tilt head is being
controlled via the AW-HB605, it is
necessary to select the number to which
the AW-HB605 is connected using the
pan/tilt head selector switch of the AW-
RP305.
AW-RP501:
TALLY HOT and GND terminals.
AW-RP505:
TALLY 5 and GND terminals.
$Priority Switchbox
<

1312
MENU
OPT CN CARD
VIDEO OUT
LF REMCTE
GL N
DC12V IN
IRIS
TEM AWC
YES ABC
NO BAR
O I
PREVIEW OUT
CAM CONT IN
5
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
4
PAN/T ILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
TO CONTROL PANEL TO PAN/TILTHEAD HUB
CAM CONT IN
3
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
2
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
1
PAN/TILT
CONTROL IN
BLACK
BURST OUT
BLACK
BURST
OUT
PREVIEW IN
CAM CONT OUT
PAN/T ILT
CONTROL OUT
+-
DC12V IN
O I
Convertible camera
Iris control cable
Remote (zoom/focus control) cable
Pan/tilt head: AW-PH300
Camera mounting
adapter
Pan/tilt head cable:
AW-CA50T15
Pan/tilt head AC adapter:
AW-PS300
AC 120 V
AC adapter:
AW-PS505
AC 120 V
AC adapter:
AW-PS301
AC 120 V
Monitor
Multi pan/tilt control panel:
AW-RP305
Multi control hub:
AW-HB605
Priority
switchbox
Coaxial cable:
Video signal
10BASE-T cable:
Pan/tilt head control
signal
10BASE-T cable:
Pan/tilt head control
signal
System Connections (Indoor Pan/tilt Head System)
$System Incorporating AW-RP305
<Note>
Since the multi pan/tilt control panel is not equipped with a video signal compensation
circuit, it may be necessary to use a separate cable compensation device in some cases.
Maximum Cable Length
The maximum cable length from the camera and
pan/tilt head to the multi pan/tilt control panel is 500
meters.
O I
PREVIEW OUT
CAM CONT IN
5
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
4
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
TO CONTROL PANEL TO PAN/TILTHEAD HUB
CAM CONT IN
3
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
2
PAN/T ILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
1
PAN/TILT
CONTROL IN
BLACK
BURST OUT
BLACK
BURST
OUT
PREVIEW IN
CAM CONT OUT
PAN/TILT
CONTROL OUT
+-
DC12V IN
O I
MENU
OPT CN CARD
VIDEO OUT
LF REMCTE
GL N
DC12V IN
IRIS
TEM AWC
YES ABC
NO BAR
System Connections (Indoor Pan/tilt Head System)
Convertible camera
Iris control cable
Remote (zoom/focus control) cable
Pan/tilt head: AW-PH300
Camera mounting
adapter
Pan/tilt head cable:
AW-CA50T15
Pan/tilt head AC adapter:
AW-PS300
AC 120 V
AC adapter:
AW-PS505
AC 120 V
AC adapter:
AW-PS301
AC 120 V
Monitor
Pan/tilt control panel:
AW-RP301
Multi control hub:
AW-HB605
Priority
switchbox
Coaxial cable:
Video Signal
10BASE-T cable:
Pan/tilt head control
signal
10BASE-T Cable:
Pan/tilt head control
signal
$System Incorporating AW-RP301
<Note>
Since the pan/tilt control panel is not equipped with a video signal compensation circuit, it
may be necessary to use a separate cable compensation device in some cases.
Maximum Cable Length
The maximum cable length from the camera and
pan/tilt head to the pan/tilt control panel is 500 meters.

1514
MENU
OPT CN CARD
VIDEO OUT
LF REMCTE
GL N
DC12V IN
IRIS
TEM AWC
YES ABC
NO BAR
O I
PREVIEW OUT
CAM CONT IN
5
PAN/T ILT
CONTROLIN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
4
PAN/TILT
CONTROLIN
BLACK
BURST OUT
PREVIEW OUT
TO CONTROL PANEL TO PAN/TILTHEAD HUB
CAM CONT IN
3
PAN/TILT
CONTROLIN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
2
PAN/TILT
CONTROLIN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
1
PAN/TILT
CONTROLIN
BLACK
BURST OUT
BLACK
BURST
OUT
PREVIEW IN
CAM CONT OUT
PAN/TILT
CONTROLOUT
+-
DC12V IN
O I
O I
System Connections (Indoor Pan/tilt Head System)
Convertible camera
Iris control
cable
Remote (zoom/focus control) cable
Pan/tilt head: AW-PH300
Camera mounting
adapter
Pan/tilt head cable:
AW-CA50T15
Pan/tilt head AC adapter:
AW-PS300
AC 120 V
AC adapter:
AW-PS505
AC 120 V
AC adapter:
AW-PS505
AC 120 V
AC adapter:
AW-PS301
AC 120 V
Preview
monitor
Monitor
S-Video
Multi hybrid control
panel:
AW-RP505
Multi port hub:
AW-HB505
Multi control hub:
AW-HB605
Priority
switchbox
Coaxial cable:
Video signal
Coaxial cable:
Gen-lock signal
Coaxial cable:
Camera control signal
Coaxial cable:
Camera control signal
Coaxial cable:
Video signal
Coaxial cable:
Gen-lock signal
Coaxial cable:
Camera control signal
Coaxial cable:
Video signal
10BASE-T cable:
Pan/tilt head control signal
10BASE-T cable:
Pan/tilt head control
signal
$System Incorporating AW-RP505 or
AW-HB505
Maximum Cable Length
The maximum cable length from the camera and
pan/tilt head to the multi hybrid control panel is 500
meters.
MENU
OPT CN CARD
VIDEO OUT
LF REMCTE
GL N
DC12V IN
IRIS
TEM AWC
YES ABC
NO BAR
PREVIEW OUT
CAM CONT IN
5
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
4
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
TO CONTROL PANEL TO PAN/TILTHEAD HUB
CAM CONT IN
3
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
2
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
1
PAN/TILT
CONTROL IN
BLACK
BURST OUT
BLACK
BURST
OUT
PREVIEW IN
CAM CONT OUT
PAN/TILT
CONTROL OUT
+-
DC12V IN
O I
O I
System Connections (Indoor Pan/tilt Head System)
Convertible camera
Iris control cable
Remote (zoom/focus control) cable
Pan/tilt head: AW-PH300
Camera mounting
adapter
Pan/tilt head cable:
AW-CA50T15
Pan/tilt head AC adapter:
AW-PS300
AC 120 V
AC adapter:
AW-PS505
AC 120 V
AC adapter:
AW-PS301
AC 120 V
Monitor
S-Video
Hybrid control panel:
AW-RP501
Multi Control Hub:
AW-HB605
Priority
switchbox
Coaxial cable:
Video Signal
Coaxial cable:
Camera control signal
Coaxial cable:
Camera control signal
Coaxial cable:
Video signal
10BASE-T cable:
Pan/tilt head control
signal
10BASE-T cable:
Pan/tilt head control
signal
$System Incorporating AW-RP501
Maximum Cable Length
The maximum cable length from the camera and
pan/tilt head to the hybrid control panel is 500 meters.

POWER
1
YC
2
YC
3
YC
4
YC
5
YC
OFF ON
CABLE COMP
Multl Port Hub AW-H8505
O I
O I
POWER
OFF ON
1716
Operations
1. Turn the power on.
Turn on the power control switches of
the AC adapters of the pan/tilt heads
and control panels, as well as the AC
adapter and power control switch of the
multi control hub.
If the system incorporates a multi port
hub, turn on the power control switch of
the multi port hub and the power switch
of its AC adapter.
2. Press the button on the priority
switchbox connected to the control
panel you wish to operate. This
activates the connected control panel.
If the system incorporates a multi hybrid
control panel, use the camera and
pan/tilt head selector switch on the multi
hybrid control panel to select a pan/tilt
head. (The control panel is activated
once its memory switch stops flashing
and goes dark.)
<Notes>
OImmediately after the power is turned
on the system is in a status in which
no control panel is selected. After
turning the power on, do not fail to
press the priority switchbox
connected to the control panel you
wish to operate. After this operation
is performed the power supply to the
camera and pan/tilt head turns on.
OThe active control panel is always the
one connected to the priority
switchbox pressed last.
3. Perform the mounting balance
adjustment on the cameras. For detailed
instructions, refer to the manuals
accompanying the relevant equipment.
4. Set the limits to the range of movement
for the pan/tilt head (limiter). For
detailed instructions, refer to the
manuals accompanying the relevant
equipment.
5. If the system incorporates a hybrid
control panel or multi hybrid control
panel, perform video signal cable
compensation, G/L (gen-lock)
adjustment, and total pedestal
adjustment. Also set the switches as
appropriate. For detailed instructions,
refer to the manuals accompanying the
relevant equipment.
<Note>
After performing G/L (gen-lock)
adjustment and total pedestal
adjustment, set the control panel’s G/L
phase adjustment switch to the OFF
position. The instruction manual of the
hybrid control panel states that this
switch should be left in the ON position,
but it should be set to OFF on systems
using the multi control hub.
6. Store the preset settings for the
cameras and pan/tilt heads in memory
(systems incorporating hybrid control
panel or multi hybrid control panel only).
For detailed instructions, refer to the
manuals accompanying the relevant
equipment.
<Note>
The preset settings are stored in the
memory of the pan/tilt head. When new
preset settings are stored in memory, all
the previous settings (including those
stored in memory using the control
panel) are overwritten.
The adjustments and settings described
in steps
3 though 6 above may be
omitted if no changes need to be made to
the current adjustments and settings.
Zoom/focus control
Option switch
control:
Unnecessary if no
optional unit is
connected.
DC15V
Lamp control:
Unnecessary if no
halogen lamp is used.
Pan/tilt head AC
adapter:
AW-PS300
Optional unit
Contact
Gen-lock
Video
Video S-Video
Preview Video
Preview Video
Preview Video
Gen-lock
Camera control
Camera control
Pan/tilt head
control
Pan/tilt head control
Camera control
Pan/tilt head control
Halogen lamp
Servo control
zoom lens
Convertible
camera
Color monitor
(75 Ωterminator)
Preview color
monitor
(75 Ωterminator)
Camera cable:
AW-CA50T15
Iris control
AC adapter:
AW-PS505
AC adapter:
AW-PS505
AC adapter:
AW-PS301
Multi hybrid control
panel:
AW-RP505
Multi port hub:
AW-HB505
Multi control hub:
AW-HB605
Priority
switchbox
Adjustment such as cable compensation, gen-
lock adjustment, and total pedestal adjustment
should be applied to the video signals output
from the AW-HB505.
System Connections (Indoor Pan/tilt Head System)
$Example System Setup

1918
Specifications
Power supply:
DC +12 V (4-pin Cannon Connector)
Power consumption:
DC 12 V, 0.47 A
Video input:
Composite video 1 V [p-p] 75 Ωa1
(BNC connector)
Camera control inputs:
Control signal (BNC connector) a5
Pan/tilt head control inputs:
Control signal (RJ-45 8-pin modular
jack) a5
Preview video outputs:
Composite video 1 V [p-p] 75 Ωa5
(BNC connector)
Black burst outputs:
75 Ωa6 (BNC connector)
Camera control output:
Control signal (BNC connector)
Pan/tilt head control output:
Control signal (RJ-45 8-pin modular
jack)
Switch function:
Power on/off
Control panel connecting cables:
Number of connecting cables: 4 (3
coaxial cables, 1 10BASE-T straight
cable); 5 sets (when using G/L function)
Pan/tilt head connecting cables:
4 connecting cables per pan/tilt head (3
coaxial cables, 10BASE-T straight
cable)
(when using G/L function)
Maximum cable length:
Length of cable from camera and pan/tilt
head to control panel: Max. 500 m
(assuming: coaxial cable: 5C-2V,
10BASE-T straight cable: UTP category
5)
Operating temperature range:
+14°F to +113°F (–10°C to +45°C)
Dimensions (WaHaD):
Body:
16 9/16˝a3 1/2˝a9 7/8˝
(420a88a250 mm)
Priority switchbox:
2 13/16˝a3 1/2˝a1 7/16˝
(70a88a35 mm)
Weight:
Approx. 12.32 lb (5.6 kg)
Finish:
Cover:
Steel panel with AV ivory color
polyvinyl chloride finish (approximate
color: Munsell 7.9Y 6.8/0.8)
Panel:
AV ivory color paint (approximate
color: Munsell 7.9Y 6.8/0.8)
Rack Mounting Example
$Rack Mounting Procedure
Multi Control Hub
To mount the multi control hub on a rack,
use the supplied rack mounting brackets
and mounting screws (M4a10).
1Press the power switch to turn power
off.
2Remove the four feet from the bottom of
the multi control hub.
3Secure the rack mounting brackets to
the sides of the multi control hub using
the supplied mounting screws (a4).
4Mount the multi control hub in the rack
and secure it in place using four rack
mounting screws (part number W2-
MSS/5008).
Switchbox
To mount the switchbox on a rack, use the
supplied rack mounting brackets and
mounting screws (M4a8).
Power switch
Rack mounting bracket
Rack mounting screws
W2-MSS/5008
(Option)
Mounting screws
Rack mounting bracket
Mounting screws
Feet
<Notes>
ORack mounting screws sold separately (part number W2-MSS/5008).
OTo ensure that the temperature within the rack does not exceed +113°F (+45°C), make
sure to provide sufficient space (a minimum of one chassis width between units)
between the multi control hub and the other pieces of equipment mounted in the rack
or install a cooling fan.
Weight and dimensions indicated are
approximate.
Specifications are subject to change
without notice.