Panasonic MC-UL810-00 Building instructions

© 2011 PANASONIC CONSUMER ELECTRONICS
COMPANY, DIVISION OF PANASONIC
CORPORATION OF NORTH AMERICA. All rights
MC-UL810-00
Vacuum Cleaner
Specifications are subject to change without notice for further improvement.
Order Number MAC1106001CE

1 WIRING DIAGRAM AND DRAWING 3
1.1. Wiring Diagram 3
1.2. Wire Management Drawing 4
2 EXPLODED VIEW AND PARTS LIST 5
2.1. Body 5
2.2. Nozzle Housing 7
2.3. Dust Bin Assembly 9
2.4. Packing Materials 11
3 SERVICE PROCEDURES 12
3.1. CORD REEL 12
3.2. FAN MOTOR 14
3.3. ON/OFF SWITCH 15
CONTENTS
Page Page
2
MC-UL810-00

1 WIRING DIAGRAM AND DRAWING
1.1. Wiring Diagram
3
MC-UL810-00

1.2. Wire Management Drawing
NOTE:
For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical
component or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage.
Use part number AC79FCWZZ000 (FIBERGLASS CLOTH TAPE) whenever original tape is removed.
4
MC-UL810-00

2 EXPLODED VIEW AND PARTS LIST
2.1. Body
2.1.1. Exploded View
5
MC-UL810-00

2.1.2. Parts List
Ref. No. Part No. Part Name & Description Quantity Remarks
1 AC60KDNYZUU3 DUST COVER (DECO) 1
2 AC39LDNYZV07 AIR GUIDE 1
3 AC40KDNYZV07 DUST COMPARTMENT 1
4 AC24ADNYZC0Q BODY COVER 1
5 AC01BDNYZV07 HANDLE 1
6 AC70PDNYZV07 EXTENSION WAND HOLDER 1
7 AC10UDNYZV07 PIN 1
8 AC19PDNYZV07 HOSE COVER 1
9 AC58PDMTZV07 HOSE ADAPTER 1
10 AC45KDMTZU00 VALVE GROMMET 1
11 AC60RCNFZV07 CREVICE TOOL 1
12 AC84PDMTZV07 EXTENSION WAND UNIT ASSEMBLY 1
13 AC23BDNYZV07 HANDLE GRIP LEFT 1
14 AC22BDNYZU03 HANDLE GRIP RIGHT 1
15 AC82DDNYZV07 LOCK CLIP 1
16 AC80SCRZZV0N TURBINE UNIT 1
17 AXTN4+16BFY SCREW 15 SHIPPED 10 PER PACKAGE
18 AC73BZAZ00 HANDLE SCREW 1 SHIPPED 10 PER PACKAGE
6
MC-UL810-00

2.2. Nozzle Housing
2.2.1. Exploded View
7
MC-UL810-00

2.2.2. Parts List
Ref. No. Part No. Part Name & Description Quantity Remarks
1 AC06ADNYZUU3 BODY PLATE (DECO) 1
2 AC14NDNYZC0Q CORD GUIDE 1
3 AC23DDEVZ000 SPRING 1
4 AXTN4+16BFY SCREW 15 SHIPPED 10 PER PACKAGE
5 AC05EDNYZM0L SWITCH BUTTON 1
6 AC01EDDRZ000 ON/OFF SWITCH 1
7 AC58FDPAZU00 MOTOR SHIELD 1
8 AC92FDNYZ000 FAN MOTOR UNIT 1
9 AC74KBKHZ000 DUST PACKING 1
10 AC28SJPZ00 BELT-FLAT 1
11 AC03FDNYZ000 MOTOR SUPPORT RUBBER (REAR) 1
12 AC32KDPAZU00 FILTER SUPPORTER 1
13 AC38KDDJZ000 EXHAUST FILTER (HEPA) 1
14 AC76FDMUZ000 OVERLOAD PROTECTOR 1
15 AC21RDNYZC0Q NOZZLE ARM 1
16 AC12ADNYZC0Q BODY CAP 1
17 AC91PDNYZV07 NOZZLE HOSE UNIT (A) 1
18 AC99NDNYZV07 CORD REEL ASSEMBLY 1
19 AC47ADPAZV04 PEDAL (HANDLE RELEASE) 1
20 AC91PDPAZV07 NOZZLE HOSE UNIT (B) 1
21 AC01ADNYZU03 NOZZLE HOUSING 1
22 AC08DDMTZV07 LATCH 2
23 AC02ADNYZCUR UPPER BODY (DECO) 1 INCLUDES PACKING
24 AC10ADNYZV07 FURNITURE GUARD 1
25 AC92SDNZZY05 AGITATOR ASSEMBLY 1
26 AC28SDNYZ000 BELT 1
27 AC78ADNYZV07 HOLDER 1
28 AC71KDNYZ000 SPRING 1
29 AC27ADNYZV07 LOWER PLATE 1
30 AC02CDNYZ000 WHEEL SUPPORTER (AXLE) 3
31 AC99CDNYZU03 WHEEL UNIT 2 SHIPPED 2 PER PACKAGE
32 AXWG6E115FY WASHER 2 SHIPPED 10 PER PACKAGE
33 AC23FBVNZ000 RING CLIP 2
34 AC16CBBRZ00 ROLLER SHAFT 2 SHIPPED 2 PER PACKAGE
35 AC99CCXWZV07 WHEEL UNIT 2 SHIPPED 2 PER PACKAGE
36 AC34HDNYZV07 HEIGHT ADJUST ACTUATOR 1
37 AC85GDNYZ000 BLACK LEAD WIRE UNIT 1
38 AC85GDPAZ000 BLACK LEAD WIRE UNIT 1
39 AC85GDNZZ000 BLACK LEAD WIRE UNIT 1
40 AC85WDNYZ000 WHITE LEAD WIRE UNIT 1
41 AC37KDNYZ000 SECONDARY FILTER 1
8
MC-UL810-00

2.3. Dust Bin Assembly
2.3.1. Exploded View
9
MC-UL810-00

2.3.2. Parts List
Ref. No. Part No. Part Name & Description Quantity Remarks
1 AC14BDMTZU03 HANDLE LID 1
2 AC64NDMTZM0L PRESS BUTTON 1
3 AC18DBRMZ000 SPRING 1
4 AC64HARTZ000 SUCTION INLET PACKING 1
5 AC20HDPAZC0Q LID 1
6 AXTN4+16BFY SCREW 9 SHIPPED 10 PER PACKAGE
7 AC44KDPAZ000 FILTER 1
8 AC75KDPAZ0U0 DUST BOX TERMINAL 1
9 AC39LDPAZC0Q AIR GUIDE 1
10 AC03LDMTZU00 GASKET A 1
11 AC97LDMTZU00 PARTITION ASSEMBLY 1
12 AC36KDMUZC0Q SUPPORTER UNIT 1
13 AC43KDMTZC0R PRE-FILTER 1
14 AC42KDNYZ0U0 FILTER CASE 1
15 AC48KDGNZM0L SLIDER 1
16 AC73KDMTZU00 DUST PACKING 1
17 AC25KDMTZ000 DUST BOX PLATE 1 INCLUDES PACKING
18 AC37KDPAZ000 FILTER 1
10
MC-UL810-00

2.4. Packing Materials
2.4.1. Exploded View
2.4.2. Parts List (Packing Material)
Ref. No Part No. Part Name & Description Quantity Remarks
1 AC61ZDNYZ000 Packing Assembly 1 Includes Items A thru H
2 AC01ZDNYZ000 Operating Instructions 1
11
MC-UL810-00

3.1. CORD REEL
3.1.1. Removal
1. Press tab and remove hose cover.
2. Remove lower nozzle hose from hose holder by pulling
down on the nozzle hose. It may be necessary to slightly
twist the nozzle hose to loosen from the hose holder.
3. Remove screw and pin.
4. Remove upper nozzle hose by Inserting a flat screwdriver
into the slot in the dust container as show and gently pry
hose from body.
5. Press the body slight forward, then tilt back to remove from
nozzle.
3 SERVICE PROCEDURES
12
MC-UL810-00

6. Press nozzle latches and remove nozzle housing.
7. Press handle release pedal and rotate nozzle arm down.
8. Remove two (2) screws from body cap and lift off.
9. Rotate nozzle arm up and lift off.
10. Remove five (5) screws from body plate and lift off.
11. Remove cord guide from body plate by gently prying with a
flat screwdriver from the inside of the body plate. Use
caution as this part may break very easily.
13
MC-UL810-00

12. Pull power cord plug through the body plate.
13. Lay body plate aside.
14. Remove one (1) screw and cord reel from the lower plate.
15. Disconnect lead wires.
16. Discard cord reel.
WARNING: DO NOT REMOVE THE METAL COVER
SCREWS. REMOVAL OF THE COVER WILL ALLOW
THE SPRING INSIDE TO UNWIND AND CAUSE
PERSONAL INJURY
NOTE: For general servicing, it is necessary to eliminate
pinching of any wire during reassembly. After servicing
any electrical component or electrical enclosure, the
vacuum cleaner should be reassembled and checked for
dielectric breakdown or current leakage.
3.1.2. Installation
1. Connect lead wires to the appropriate terminals on the cord
reel (see WIRING DIAGRAM).
2. Insert cord reel into lower plate and reinstall one (1) screw.
3. Route the plug through the body plate.
4. Reinstall cord guide (replace if broken during disassembly).
5. Reinstall body plate and secure with five (5) screws.
6. Reinstall nozzle cover. Make sure that the latches are
locked into the slots.
7. Replace body, insert pin and reinstall one (1) screw.
8. Attach nozzle hose inside the body.
9. Attach lower nozzle hose to hose holder and reinstall hose
cover.
3.2. FAN MOTOR
3.2.1. Removal
1. Remove body, nozzle cover and body plate (See CORD
REEL - Removal).
2. Remove two (2) screws.
3. Lift out motor assembly.
4. Remove two (2) screws from motor enclosure.
5. Remove motor shield and lift out fan motor.
14
MC-UL810-00

6. Remove lead wires from fan motor terminals.
3.2.2. Installation
1. Install fan motor into motor shield.
2. Place motor wires in retention slot (see WIRE
MANAGEMENT and WIRING DIAGRAM illustrations).
3. Install filter supporter and two (2) screws.
4. Route wires according to WIRE MANAGEMENT and
WIRING DIAGRAM illustrations.
5. Place motor assembly into lower place and replace two (2)
screws.
6. Route wires in lower plate (see WIRE MANAGEMENT
illustration).
7. Reinstall body plate and secure with five (5) screws.
8. Reinstall nozzle cover. Make sure that the latches are
locked into the slots.
9. Replace body, insert pin and reinstall one (1) screw.
10. Attach nozzle hose inside the body.
11. Attach lower nozzle hose to hose holder and reinstall hose
cover.
NOTE: For general servicing, it is necessary to eliminate
pinching of any wire during reassembly. After servicing
any electrical component or electrical enclosure, the unit
should be reassembled and checked for dielectric
breakdown or current leakage.
3.3. ON/OFF SWITCH
3.3.1. Removal
1. Remove body, nozzle cover and body plate (See CORD
REEL - Removal, steps 1-7).
2. Remove motor assembly (See FAN MOTOR - Removal,
steps 1-4).
3. Remove motor shield (See FAN MOTOR - Removal).
4. Remove switch from filter supporter.
5. Disconnect lead wires from switch and remove defective
switch.
3.3.2. Installation
1. Reconnect lead wires to switch.
2. Reinstall switch into filter supporter.
3. Reinstall motor shield (See FAN MOTOR - Installation).
15
MC-UL810-00

4. Reinstall motor assembly into lower plate (See FAN
MOTOR - Installation).
5. Route wires in lower plate (see WIRE MANAGEMENT
illustration).
6. Reinstall body plate and nozzle cover (see FAN MOTOR -
Replacement).
7. Reinstall nozzle cover. Make sure that the latches are
locked into the slots.
8. Replace body, insert pin and reinstall one (1) screw (See
CORD REEL - INSTALLATION).
9. Attach nozzle hose inside the body (See CORD REEL -
INSTALLATION).
10. Attach lower nozzle hose to hose holder and reinstall hose
cover (See CORD REEL - INSTALLATION).
16
MC-UL810-00