Panduit ATLONA AT-USB-EX100-KIT User manual

1
Installation Guide
AT-USB-EX100-KIT
IMPORTANT: Visit https://www.atlona.com/product/AT-USB-EX100-KIT for the latest
rmware updates and User Manual.
1 x AT-USB-EX100-TX
1 x AT-USB-EX100-RX
2 x 5 V / 4 A Power Supplies
4 x Mounting Plates
8 x Mounting Screws
1 x Installation Guide
Package Contents
HDBaseT Extender Kit for USB 2.0
AT-USB-EX100-KIT
The Atlona AT-USB-EX100-KIT is a long-distance extender kit for high speed USB signals. It
supports transmission of USB 2.0 data up to 330 feet (100 meters) using a single, cost eective
Category-type twisted pair cable. The AT-USB-EX100-KIT is ideal for popular conferencing
applications such as Zoom® and Microsoft® Teams®, where USB components including
laptops, cameras, microphones, and speakers are located in dierent areas of the room. The kit
is also suitable in classrooms for routing USB between an interactive display or projector, and
the instructor’s laptop. The AT-USB-EX100-KIT includes both transmitter and receiver endpoints.
Compact enclosures and included brackets allow the devices to be discretely mounted near
computers and USB peripherals. The AT-USB-EX100-KIT is a great solution for connecting USB
components separated by distances not supported by traditional cabling.

2
Installation Guide
AT-USB-EX100-KIT
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
1 DEVICE
Connect up to two USB devices (e.g. mouse, keyboard, etc.) to these ports. These ports
provide 2.5 W per USB device interface.
2 HOST
Connect a USB cable from this port to the host computer.
3 FW
Connect a micro-USB to USB-A cable from this port, to a computer, to update the rmware.
4 PWR
The PWR LED indicator will glow green when the AT-USB-EX100-TX is powered.
5 DC 5V
Connect the included 5 V DC power supply to this power receptacle.
6 HDBaseT OUT
Connect a category cable from this port to the HDBaseT IN port of the AT-USB-EX100-RX.
Front
Rear
5 6
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
2
1 3 4
AT-USB-EX100-TX

3
Installation Guide
AT-USB-EX100-KIT
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
1 DEVICE
Connect up to four USB devices (e.g. mouse, keyboard, etc.) to these ports. These ports
provide 2.5 W per USB device interface.
2 FW
Connect a micro-USB to USB-A cable from this port, to a computer, to update the rmware.
3 PWR
The PWR LED indicator will glow green when the AT-USB-EX100-RX is powered.
4 DC 5V
Connect the included 5 V DC power supply to this power receptacle.
5 HDBaseT OUT
Connect a category cable from this port to the HDBaseT IN port of the AT-USB-EX100-TX.
Front
Rear
4 5
1 2 3
AT-USB-EX100-RX

4
Installation Guide
AT-USB-EX100-KIT
Core Shielding CAT5e CAT6 CAT6a CAT7
Solid UTP (unshielded) N/A
STP (shielded)
1. Connect up to two USB devices (speakerphone, etc.) to the DEVICE ports on the AT-USB-
EX100-TX. These ports provide 2.5 W per USB device interface.
2. Connect a USB cable from the host device to the HOST port on the AT-USB-EX100-TX.
3. Connect up to four USB devices (mouse, keyboard, etc.) to the DEVICE ports on the AT-
USB-EX100-RX. These ports provide 2.5 W per USB device interface.
4. Connect a category cable (CAT5e or better), from the HDBaseT OUT port on the AT-USB-
EX100-TX, to the HDBaseT IN port on the AT-USB-EX100-RX. Maximum cable length
should not exceed 330 feet (100 meters).
5. Connect the included 5 V DC power supplies to both the AT-USB-EX100-TX and AT-USB-
EX100-RX to the DC 5V power receptacles.
6. Connect both power supplies to available AC outlets.
Refer to the tables below for recommended cabling when using Altona products with HDBaseT.
The green bars indicate the signal quality when using each type of cable. Higher-quality signals
are represented by more bars.
IMPORTANT: Stranded or patch cables are not recommended due to
performance issues.
Installation
Cable Recommendation Guidelines
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
12
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
FW PWRHOSTDEVICE
AT-USB-EX100-TX
DC 5V HDBaseT OUT
FW PWR
AT-USB-EX100-RX
DC 5V HDBaseT IN
DEVICE
3
45
54
NOTE: This product is not a PoE device. The included power supplies must
be connected to both the AT-USB-EX100-TX and AT-USB-EX100-RX.

5
Installation Guide
AT-USB-EX100-KIT
PWR Description
Solid green Unit is powered.
O Unit is not powered.
• Verify that the locking connector is securely fastened to the
power receptacle.
• Make sure that the power supply is connected to an active
AC outlet.
The PWR indicator on both the AT-USB-EX100-TX and AT-USB-EX100-RX provide power state
information on both the AT-USB-EX100-TX and AT-USB-EX100-RX.
LED Indicators
Both the AT-USB-EX100-TX and AT-USB-EX100-RX include mounting brackets, which can be
used to attach the unit to any at surface. Use the included screws to attach the mounting
brackets.
1. Using a small Phillips screwdriver, remove the two screws from the side of the enclosure.
Mounting Instructions
FW PWRHOSTDEVICE

6
Installation Guide
AT-USB-EX100-KIT
2. Position the mounting brackets, as shown below, aligning the holes on the side of the
enclosure with one set of holes on the mounting bracket.
3. Use the screws from Step 1 to attach the mounting brackets, plus two additional screws
(included) to complete the installation. Four screws should be used to secure each
mounting bracket, as shown below.
FW PWRHOSTDEVICE
FW PWRHOSTDEVICE
4. Mount the unit to a at surface using the oval-shaped holes, on each mounting bracket.
If using a drywall surface, a #6 drywall screw is recommended.
NOTE: Mounting brackets can also be inverted to mount the unit under a table
or other at surface.

7
Installation Guide
AT-USB-EX100-KIT
Requirements:
• AT-USB-EX100-TX
• AT-USB-EX100-RX
• Firmware le
• Computer running Windows
• USB-A to USB micro-B cable
1. Disconnect power from the AT-USB-EX100-TX.
2. Connect a USB-A to USB micro-B cable between the PC and the FW port on the AT-USB-
EX100-TX.
3. Reconnect power to the AT-USB-EX100-TX and AT-USB-EX100-RX.
4. Connect an HDBaseT cable from the HDBaseT OUT port on the transmitter to the
HDBaseT IN port on the receiver.
5. The PWR LED indicator on the AT-USB-EX100-TX will start ashing.
6. The USB UPDATE folder will be displayed. If this folder is not displayed, automatically,
select the USB UPDATE drive from Windows Explorer.
7. Delete all les from the USB UPDATE drive, if any are present.
8. Drag-and-drop the rmware le to the drive.
9. The PWR LED indicator on the front panel will ash green while the unit is being updated.
Do not disconnect the USB cable during the update process. When the PWR LED stops
ashing and is solid green, the update process will be complete.
10. Disconnect the USB cable from the unit.
11. The rmware update process is complete.
Updating the Firmware

8
Installation Guide
AT-USB-EX100-KIT
Version 4 25257-R4
© 2022 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
English Declaration of Conformity
Warranty
Chinese Declaration of Conformity 中国RoHS合格声明
To view the product warranty, use the following link or QR code:
https://atlona.com/warranty/.
由SKU列出於:
https://atlona.com/about-us/china-rohs/.
The English version can be found under the resources tab at:
https://atlona.com/product/at-usb-ex100-kit/.
US International
atlona.com •408.962.0515 •41.43.508.4321