Panduit Atlona OmniStream 111 User manual

1
Installation Guide
AT-OMNI-111
OmniStream 111 Single-Channel Networked AV Encoder
AT-OMNI-111
1 x AT-OMNI-111
1 x Push spring connector, 6-pin
1 x Wall/table mounting brackets
4 x Rubber feet
1 x Installation Guide
Package Contents
IMPORTANT: Visit http://www.atlona.com/product/AT-OMNI-111 for the latest
rmware updates and User Manual.
The Atlona OmniStream™ 111 (AT-OMNI-111) is a single-channel networked AV encoder for
HDMI 2.0 sources up to 4K @ 60 Hz and HDR (High Dynamic Range), plus embedded audio
and RS-232 or IR control pass-through. It is part of the OmniStream Series, designed for high
performance, exible distribution of AV over standard o-the-shelf Gigabit Ethernet switches in
commercial audio visual applications. The OmniStream 111 is HDCP 2.2 compliant and ideal
for the latest Ultra High-Denition and HDR sources. It features advanced high-quality VC-2
visually lossless video compression technology for computer-generated imaging, or motion video
content. The Atlona OmniStream™ 111 achieves extremely low, sub-frame latency when paired
with OmniStream Decoders. This single-channel encoder is housed in a half-width rack with
front-to-back air ow enclosure, and is ideal for high-density, compact installation in a centralized
equipment location.
Operating Notes
• Atlona recommends using the Velocity with Integrated AMS which provides discovery,
management, and conguration assistance. Velocity with Integrated AMS is a free
application that can be downloaded from the Atlona web site at http://atlona.com/product/
at-ams-sw/.
• OmniStream uses mDNS as the discovery mechanism. In order for mDNS to function
properly, there must not be restrictions applied to the network. Although VPN can be used
to connect to a computer that is running Velocity, on the same network, it cannot be used
when Velocity is running on the local machine.

2
Installation Guide
AT-OMNI-111
Panel Descriptions
AT-OMNI-111
ETHERNET
RS-232
DC 48V
RX TX
1
HDMI IN
HDMI
PWR LINK
TM
O MNI S TREAM
ID
1
876 9
2 3 54
1 PWR
This LED indicator glows bright green when
the unit is powered.
2 HDMI
This LED indicator shows the input status.
3 LINK
This LED indicator is green when the link
integrity between the encoder and the
switch is good.
4 ID
This button provides two functions:
(1) Press and release this button to send
a broadcast network notication to any
devices that may be listening (AMS).
(2) Press and hold this button for 30
seconds to perform a factory-reset of the
unit. Refer to the OmniStream Encoder
User Manual for more information.
5 REBOOT
Use a small, pointed object to press this
recessed button and reboot the unit.
6 HDMI IN
Connect an HDMI cable from this port to an
HD source.
7 ETHERNET
Connect an Ethernet cable from this port to
the Local Area Network (LAN).
8 RS-232
Use the included captive screw connector
to connect an RS-232 device to this
port. Refer to RS-232 on page 5 for more
information.
9 DC 48V
Connect the optional 48V DC power supply
to this power receptacle. This power supply
is available, separately, and is required
when connecting the encoder to non-PoE
compatible switch.

3
Installation Guide
AT-OMNI-111
The AT-OMNI-111 encoder includes two
mounting brackets and four mounting screws,
which can be used to attach the unit to any at
surface.
1. Using a small Phillips screwdriver, remove
the two screws from the left side of the
enclosure.
2. Position one of the mounting brackets, as
shown below, aligning the holes on the
side of the enclosure with one set of holes
on the mounting bracket.
3. Use the enclosure screws to secure the
mounting bracket to the enclosure.
4. To provide added stability to the mounting
bracket, use two of the included screws
and attach them to the two holes, directly
below the enclosure screws, as shown
above.
5. Repeat steps 1 through 4 to attach the
second mounting bracket to the opposite
side of the unit.
6. Mount the unit using the oval-shaped
holes, on each mounting bracket. If using
a drywall surface, a #6 drywall screw is
recommended.
1
2
HDMIPWR
1
2
LINK DISPLAY INPUT ID
VOLUME
AT-OMNI-112
1
2
HDMIPWR
1
2
LINK DISPLAY INPUT ID
VOLUME
AT-OMNI-112
1
2
HDMI
PWR
1
2
LINK DISPLAY INPUT ID
VOLUME
AT-OMNI-112
Mounting Instructions
NOTE: Mounting brackets can
also be inverted to mount the
unit under a table or other at
surface.
Included screws

4
Installation Guide
AT-OMNI-111
HDMI
PWR LINK
TM
OMNISTREAM
AT-OMNI-111
ETHERNET
RS-232
DC 48V
RX TX
1
HDMI IN
AT-OMNI-111
ETHERNET
RS-232
DC 48V
RX TX
1
HDMI IN
HDMI
PWR LINK
TM
O MNI S TREAM
ID
1. Connect an Ethernet cable from the ETHERNET port on the encoder to a PoE-capable
switch on the Local Area Network (LAN). Note that if a PoE-capable switch is not available,
the 48V DC power supply (sold separately) must be connected to the encoder.
2. Connect an HDMI cable from a UHD/HD source to the HDMI port on the encoder.
3. If using RS-232, connect the included 6-pin captive screw connector to the RS-232 port on
the encoder.
4. The PWR indicator, on the front panel, display the power status of the encoder. When the
encoder is powered, using either PoE or the optional 48V DC power supply (not included),
the LED initially turns red. After a few moments it will turn amber, and nally green.
Installation
Power Supply (optional)
The AT-OMNI-111 is powered by PoE (Power over Ethernet), when connected to a PoE-capable
switch. If a PoE-switch is not used, then the optional 48 V power supply (Atlona part no. AT-PS-
48083-C) can be purchased, separately. Insert the positive and negative leads, from the power
supply, into the terminals of the 2-pin captive screw connector block, as shown. The orange
2-pin captive screw connector block is included with the OmniStream power supply package.
POS
White
Black NEG
PWR indicator

5
Installation Guide
AT-OMNI-111
The AT-OMNI-111 provides transport of RS-232 protocol over IP which allows communication
between a control system and an RS-232 device. This step is optional.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires.
3. Insert the TX, RX, and GND wires into correct terminal on the included push spring
connector, following the wiring diagram below. If using non-tinned stranded wire, press the
orange tab, above the terminal, while inserting the exposed wire.
NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for
ground. On some devices, the function of pins 2 and 3 are reversed.
RS-232
Push tab
to unlock GND
RX
TX
IR
The same port that provides RS-232 connections also supports bidirectional IR pass-through,
allowing a device to be controlled from either the headend or the decoder endpoint. This step is
optional. IR control is only supported on RS-232 2 port (bottom set of connectors).
IR emitter conguration IR extender conguration
GND (black)
IR emitter
SIGNAL (white/black)
RX TX GND
GND (black)
SIGNAL (white/black)
Control
Unit
TX out
GND
RX TX GND

6
Installation Guide
AT-OMNI-111
1. Launch a web browser and enter the IP address of Velocity, in the address bar.
2. Enter the required login credentials.
3. Click the Login button.
4. The Velocity with Integrated AMS Dashboard will be displayed.
5. Click the icon, in the upper-left corner.
6. Click Management >AMS Device Manager from the y-out menu.
All available encoders will be displayed under the Unassigned category. When an encoder
is unassigned, it means that it has not been assigned to a site, building, and/or room. Refer
to the Velocity User Manual for more information on these topics.
If a DHCP server is not found within 60 seconds, the encoder will be placed in Auto IP mode
and assigned an IP address within the range of 169.254.xxx.xxx. If this occurs, congure
the network interface of the computer that is running AMS, located on the same subnet
(169.254.xxx.xxx, subnet mask 255.255.0.0). Refer to User Manual for more information.
If no OmniStream encoders are found, then verify the following:
• The computer that is running Velocity must be on the same network as the
OmniStream device.
• Remove any network restrictions that may be in place. In order for mDNS to function
properly, there must not be restrictions applied to the network.
Accessing devices using Velocity with Integrated AMS

7
Installation Guide
AT-OMNI-111
7. Click the desired encoder from the Unassigned device list or from under the Device List
column.
Once the unit is selected, the Velocity with Integrated AMS interface for the encoder will be
displayed. Refer to the User Manual for more information on the interface.

8
Installation Guide
AT-OMNI-111
Accessing devices using the built-in Web Server
Identify the desired encoder by locating the MAC address on the bottom of the unit.
In the following example (refer to your unit for the actual address), the label indicates that
the MAC address for the physical interface is B8:98:B0:01:F7:EB.
MAC address
1. Connect a PC to the same network where the OmniStream encoders/decoders are
connected.
2. Locate the IP address, matching it with the MAC address of the device, using an IP scanner
or ARP.
3. Launch the desired web browser and enter the IP address of the encoder in the address bar.
4. Enter the username and password. Note that the password eld will always be masked.
The default credentials are:
Username: admin
Password: Atlona

9
Installation Guide
AT-OMNI-111
5. The System Information screen will be displayed. Refer to the User Manual for more
information on the web server interface.
6. The login process is complete.

10
Installation Guide
AT-OMNI-111
Troubleshooting
Problem Solution
PWR indicator is o. • If using a PoE (Power-over-Ethernet) switch, make
sure that the port on the switch that is connected to
the encoder, has PoE enabled. When the encoder is
powered using PoE, the PWR indicator will be green.
• Check the Ethernet cable for possible damage or loose
connections.
• Connect the optional 48V DC power supply (available
from atlona.com) to the encoder. When using an external
power supply, the PWR indicator will be red.
LINK indicator is red. • Connect an Ethernet cable to the ETHERNET port.
• Check the Ethernet cable for possible damage or loose
connections.
OmniStream encoders are
not displayed in Velocity
with AMS Integration.
• Verify that AMS and the encoder are on the same
network.
• If a DHCP server is not found within 60 seconds, the
encoder will be placed in Auto IP mode and assigned an
IP address within the range of 169.254.xxx.xxx.
To access the encoder, congure a static IP on the PC
within the same IP range, then connect the PC directly
to the encoder and congure a static IP address for the
encoder. This static IP address must be within the same
IP range that is used by the Velocity with AMS Integration
software. Otherwise, the encoder will not show up.
• Check the Ethernet cable for possible damage or loose
connections.
• Make sure that mDNS is enabled on the network.
Also, in order for mDNS to function properly, there must
not be any restrictions applied to the network.

11
Installation Guide
AT-OMNI-111
Notes

12
Installation Guide
AT-OMNI-111
Version 4
© 2020 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Toll free US International
atlona.com •877.536.3976 •41.43.508.4321
English Declaration of Conformity
Chinese Declaration of Conformity 中国RoHS合格声明
The English version can be found under the resources tab at:
https://atlona.com/product/at-omni-111/.
由SKU列出於:
https://atlona.com/about-us/china-rohs/.
The terms HDMI, HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI licensing Administrator, Inc.