Panduit NET-ACCESS NVBP User manual

INSTRUCTIONS CM627B
© Panduit Corp. 2013-2014
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Vertical Blanking Panel Installation
• Install 102mm (4in) Bulb Seal to the top of both top Vertical Blanking Panel assemblies. (shown in fig A)
• Install 26.5mm (1.0in) Bulb Seal to the top side of both top Vertical Blanking Panel assemblies. (shown in fig B)
• Insert 35mm (1.4in) Foam Seal into the top of the C channel of the top Vertical Blanking Panel assemblies and into the bot-
tom of the C channel of the bottom Vertical Blanking Panel assemblies. (shown in fig B)
• Install Foam Seal on the bottom flange of the caster seal brackets .
• Install (2) Caster Seal Brackets (1 Left, 1 Right) to the bottom air dam assemblies using (1) M5X0.8 button head torx screw
per side. (do not tighten*).
• Install bottom Vertical Blanking Panel assemblies to the frame using (4) M5X0.8 button head torx screws. Do not tighten (2)
top screws.
• Insert top Vertical Blanking Panel assemblies to the frame using (3) M5X0.8 button head torx screws. Slide the top Vertical
Blanking Panel assembly over the bottom Vertical Blanking Panel assembly. Line up the corresponding hole (shown in fig D)
with the top screw of the bottom Vertical Blanking Panel assembly. Tighten (2) top screws of bottom Vertical Blanking Panel.
• Attach the long Flap Seal to the outside flange of the Vertical Blanking Panel. Start at the top closing any gaps between the
top cap and the Vertical Blanking Panel.(shown in fig E and fig F on page 2)
• Attach Equipment Seal to the lower side to side beam and to the upper side to side beam, between the front E-rails.(shown in
fig G on page 2)
• Install foam seal to the underside of the front side to side beam. (shown in fig H on page 2)
*When cabinet is level adjust caster seal brackets to create an air tight seal to the floor. Tighten screws
*Note: Seal any remaining air gaps with Blanking Foam Seal
N ET -A CCESS N-Type Network Cabinets
(Vertical Blanking Panels NVBP )
Page 1 of 3
fig A.
fig B.
fig C.
42RU
45RU
48RU
fig D
Bulb
Seal
Foam
Seal
Bulb
Seal
Foam
Seal
Bottom Vertical
Blanking Panel
Assembly
Top Vertical
Blanking Panel
Caster Seal
Bracket
M5X0.8 Torx screws
M5X0.8 Torx
screws
Top Cap
51RU

INSTRUCTIONS CM627B
For Technical Support: www.panduit.com/resources/install_maintain.asp
fig E. fig G.
Long Flap
Seal
Long Flap
Seal
Equipment
Seal
Foam Seal fig H.
fig F.
Page 2 of 3
Foam Seal
13mm x 25mm x 68mm
Foam Seal
25mm x 51mm x 102mm
Foam Seal
25mm x 51mm x 38mm

INSTRUCTIONS CM627B
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp www.panduit.com
E-mail:
[email protected]
Phone:
866-405-6654
Page 3 of 3
Blanking Seal Bracket
Area to be Sealed Cabinet Top Caps
Vertical Blanking
Panel Seal
Top Cabinet to Cabinet Gap Sealing Installation
-Air Gap between top cap and Blanking Panels should be sealed with
Blanking Foam Seal
Blanking Seal Bracket Installation
Attach the Blanking Seal Bracket to the Bottom Vertical Blanking
Panel using [2] M5 Torx Screws
ApplyFoamSealtothebottomoftheBlankingSealBrackettoensure
an air tight seal.
Note:Thisonlyapplieswhen(2) two cabinets without Side Panels are
ganged together.
Rear of Cabinet
[2] M5 Torx Screw
Foam Seal
Rear of Cabinet