Panduit NetFrame NFR84 User manual

INSTRUCTIONS CM281G
© Panduit Corp. 2010
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 1 of 4
Modular NETFRAME™Rack and Accessories
Part Numbers: NFR84, NFD484, NFSK, NFDR4X6K, NFCDRK, NFVSM4, NFEDB23,
NFSHLF19X18, NFSHLF19X25, NFLRB, NFEP, NFD884, NFD1284, NFREB2, NFBRFK
Optional Accessories
NFR84
Modular NETFRAME Rack
(8) D-rings
NFDR4X6K
Rack Assembly
(1) Vertical
Slack Manager
NFVSM4
Step1
Lay the two vertical channels
on the floor or a pair of sturdy
saw horses to ease installa-
tion.
Install (1) Base Angle and
Front Top Flange on the verti-
cal channels using (8) 3/8”
bolts, lockwashers and nuts
provided. Do not tighten.
19” Mounting 23” Mounting
(2) Vertical Channels
(2) Base Angles
(1) Pack of (20) 3/8x1.00
Bolt, Lockwasher, Nut
(1) Front Top Flange
(1) Rear Top Flange
(2) Center Waterfalls
(1) Pack of (25) #12-24x1/2” Screws
(1) Grounding and Hardware Kit
(16) Center
D-rings
NFCDRK
(1) NETFRAME Extender
Door Brackets for
23” Mtg
(4) #10-32 Screws
NFEDB23
(1) End Panel
(6)3/8”-16x1.625” Hex Bolts
3/8”-16 Hex Nuts
3/8” Split Lockwashers
NFEP
(1) Ladder Rack
Bracket
(2)3/8”-16x1” Hex Bolts
3/8”-16 Hex Nuts
3/8” Split Lockwasher
NFLRB
(1) Shelf
(4) #12-24 Screws
NFSHLF19x18
NFSHLF19x25
(shown)
(1) Door, 4” wide w/
Mtg Brackets
(4) #10-32 Screws
NFD484
(1) Center
Door, with
brackets
NFD884
NFD1284
(2) Rear Extender
Bracket
(8) #12-24 Screws
NFREB2
(8) Bend Radius Fingers
NFBRFK
Vertical
Channel
Base Angle
Front Top
Flange
Step 2
Roll the rack on its side to install
the other base angle and rear
top flange using (8) 3/8” bolts,
lockwashers and nuts provided.
Do not tighten.
Rear Top Flange
Base Angle
(1) Spool
(2)#12-24 Screws
NFSK

INSTRUCTIONS CM281G
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 2 of 4
23.875
28.40
11.00
17.00
6.00
Location Guide: 19” Rack
Step 3
Stand the rack upright.Verify
#12-24 tapped holes are EIA
spaced at 18.31”, square the
rack and tighten bolts.
Install the two waterfalls with
the #10-32 screws provided.
.
Mount rack to floor using the location guide below for
mounting hole and overall size information.
Center Waterfall
Grounding Kit
(1) Barrel Lug
(1) 1/4”-20 Screw
Barrel Lug and
Grounding Screw
mounts to rear of
rack in one of four
optional places.
Rear
Bracket
Front
Bracket
Shelf
Plate
#10-32 Screws
C Channel J Slot
Flush
Mount
6 in.
Mount
Attach Rear Bracket to rear of
rack at desired height with
#12-24 screws. Attach Front
Bracket to front of rack at
desired height with #12-24
screws. Attach Shelf Plate to
Front and Rear Brackets with
the #10-32 screws. The Shelf
Plate “C” Channel mates with
the bracket “J’ Slot to provide
adjustable mounting. Can be
mounted “flush” or extended 6
inches.
Shelf Installation
NFSHLF19X18, NFHSLF19X25
Rear Extender Bracket Installation
NFREB2
(2) #12-24
SCREWS
Use (2) #12-24 screws to secure each
bracket in desired location
NFLRB Top Plate
attaches to Main
Bracket with (2) 3/8”-
16x1” hex bolts, 3/8”-16
hex nuts and 3/8” split-
lockwashers provided
NFLRB Top Plate
can be assembled
perpendicular to
Main Bracket to
support parallel
runs of ladder rack.
NFLRB assembles to
NFR84 using 3/8”-16x1”
hex bolt, nut, and lock-
washer provided with
NFR84
Ladder Rack Bracket Installation
NFLRB
End Panel
NFEP
NFEP attaches to
rack with (6) 3/8”-
16x.625” Hex Bolts,
3/8”-16 Hex Nuts
and 3/8” Split Lock-
washers provided.
NFEP

INSTRUCTIONS CM281G
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 3 of 4
Right side installa-
tion snaps down
Left side installation
snaps up
NFDR4x6K
D-Rings Installation:
NFDR4X6K
Center D-Rings Installation:
NFCDRK
NFCDRK
Fingers install by snapping (down right side)
(up left side) use (3) #12-24 screws to secure
each finger section in desired location.
Note:
Start finger installation from bottom of rack and
continue upwards on the right side. Start finger
installation from top of rack and continue down
on the left side.
NETFRAME Vertical Slack Manager: NFVSM4
Spool Installation
Step 1
Align buttons with
mounting leg slot
Step 3
Apply downward pres-
sure until plastic spool
clicks into place.
Step 2
Push buttons through back-
bone until mounting face is
flush with backbone.
Removal/Replacement
Step 4
Pull back on angled flange while
applying upward pressure
Step 5
Repeat steps 1-3
Angled Flange
Side Mount EIA/NETFRAME Racks
Vertical Slack Manager attaches to your frame with (3) 3/
8” bolts, nuts and lock washers.
Bend Radius Fingers Installation
NFBRFK

INSTRUCTIONS CM281G
For instuctions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maitain.asp
E-mail:
[email protected]
Fax
[phone]
www.panduit.com
Page 4 of 4
1. Use 3/8”-16x1” bolt, 3/8”-16 nut and 3/8” lockwasher provided with NETFRAME to gang two racks
together using NETFRAME junction holes located on side of rack channels.
2. Straddling the two racks, fasten Top Bracket and Bottom Bracket with #10-32x5/16” screws provided.
3. Door installs to top and bottom brackets by aligning lower hinge pin to hinge pin mounting hole.
Squeeze knobs together, then align upper hinge pin to upper hinge pin mounting hole. Release pressure
on knobs to set door in place.
Top
Bottom Bracket
NFD884
NFD484 installed to NETFRAME with
(4) #10x32 screws provided.
Door Installation
NFD484
NFEDB23
NFEDB23 installed to
NETFRAME Top Flange
with #10-32 screws
provided. To be used
when rack is set-up for
23” mounting
Center Door
NFD884
NFD1284
NFSK attaches to
rack with (2) #12-24
screws provided
Spool
NFSK