Panorama Antennas SW3-091 - v2 User manual

Installation
Instructions
4x4 MiMo Directional Panel Antenna
WMM4G[G]-6-60
SW3-091 - v2

Installation Instructions
Contact Information
Content
2
EN
3-6
7

CAUTION
Parts of the antenna are an electrical conductor. Contact with power lines can result in death, or serious injury.
Do not install the antenna where there is any possibility of contact with (or high voltage arc-over from) power
cables. The antenna and supporting mast must not be close to any power lines during installation, removal or in
the event that part of the system should accidentally fall.
If the antenna is installed above the roof line or in an exposed location, it is advisable to fit lightning
surge arrestors in the coaxial cable feed lines. Suitable units should be sourced and installed as per the
manufacturer instructions. The installer is responsible for determining if this is a requirement for the
antenna installation.
4
4. Mounting Using the Low Prole Wall Bracket
5. Pole Mounting using the Adjustable Bracket
Caution: Do not overtighten the V bolts as this may damage or distort
the mast tube section.
Offer the antenna to the mounting bracket face, fit the supplied bolts with washers and tighten securely.
Do not over-tighten as it may warp the back plate.
Ensure there are no obstructions or utilities behind the mounting surface. Use the bracket as a template
to mark the mounting hole positions. Select the correct size drill bit to suit the wall plug, drill holes and
insert wall plugs. Align the bracket over the prepared holes, insert screws and fully tighten evenly. Drill
any hole/s required for cable routing as appropriate.
Safety Check: Ensure that the bracket is securely fixed to wall before
fitting the antenna.
Fit bracket to antenna using supplied screws, washers and nuts. Offer the
multi-tilt bracket to mast in selected position and fit V bolts with washer &
nuts. Tighten by hand to allow final positioning and alignment of the
bracket. Note: directional adjustment in both azimuth (horizontal)[+/-
40deg] and elevation (vertical) [+/-20deg]can be made using the tilt/swivel
feature. Once correctly aligned, fully tighten the V bolts evenly from each
side to secure the bracket.
Offer the antenna and bracket to the wall mounting tilting the antenna
slightly away from the wall and sliding the two prongs on the antenna
bracket into the locations on the wall bracket until the antenna locates.
Becareful not to trap or damage the cable.

5
6. Routing and Terminating Coaxial Cable(s)
Plan the coaxial cable route to the wireless device to avoid running adjacent to any existing electrical
wiring and ensuring that they will not be subjected to damage.
7. Commission and Test
8. Notices
Check the comms cables:
• Carry out VSWR check, the VSWR should measure <2.5:1
• Connect the Cellular/LTE cables.
Check GPS cable (where applicable):
• Check the GPS cable with DC to measure high resistance.
• Connect the GPS cable to the GPS receiver and check for satellite acquisition.
The antenna feeds consist of a low frequency element covering 617-960/1710-2700MHz and a high
frequency element covering 2.7-6.0GHz. The higher frequency component of all feeds is vertically
polarised while the lower frequency component is configured with the following polarisations:
Cable 4G/5G A : +45° | Cable 4G/5G B : -45° | Cable 4G/5G C : -45° | Cable 4G/5G D : +45°
Secure the cable run using correct size cable clips, so as not to distort/compress the cable. It is
important that the cable is not bent sharply – note that the minimum bend radius for the cable is 25mm
(1”) and this should be considered when routing to the cable entry point. Where the antenna is installed
externally, it is good practice to create a ‘drip-loop’ at the entry point to avoid water ingress. Any excess
cable must not be coiled - it should be laid out in a figure of eight pattern and loosely secured.
SMA (m) connectors are fitted as standard. A 9mm clearance hole is required for the connector – ensure
it is not damaged when inserting through the hole.
DO NOT
• operate the transmitter when someone is within 1m (3’3”) of the antenna.
• operate the equipment in an explosive atmosphere.
• attempt to install the antennas without the proper safe equipment to access the install location.
• install the antenna near power lines.
• chew parts or put them in mouth, keep away from unsupervised children.
• install the antenna in such a way that it may fall and cause injury.

6
Directive 2011/65/EU (RoHS 2)
RoHS 2 compliance is declared per Directive 2011/65/EU and its subsequent amendments with exemption
6.c applied.
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals, EC 1907/2006)
This product contains Lead (CAS No. 7439-92-1) which is classified as an SVHC (Substance of Very High
Concern) as being toxic to reproduction under Article 57c. of REACH. Do not chew parts or put them in
mouth, keep away from unsupervised
children. Dispose of parts as WEEE waste do not send to landfill.
EU Declaration of Conformity
Object Reference: WMM4GG-6-60
Object Description: Wall Mount 4x4 MiMo Antenna with GNSS Antenna
Manufacturer: Panorama Antennas Ltd 61 Frogmore, London, SW18 1HF, U.K
.
This declaration is issued under the sole responsibility of the manufacturer
The object of the declaration described above is in conformity with the relevant Union Harmonization
Legislation below:
Directive 2014/53/EU Radio Equipment Directive (RED)
Harmonised Standards and References:
EN 301 489-1 (V2.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro
Magnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical
requirements”.
Referencing EN 61000-4-2:2009 – Electrostatic Discharge Immunity and EN 61000-4-3:2006 +A1:2008
+A2:2010 – Radiated RF Immunity
EN 300 440-1 V1.6.1 (2010-08) – Electromagnetic compatibility and radio spectrum matters (ERM); short
range devices; radio equipment to be used in the 1GHz to 40GHz frequency range; Part 1: Technical
characteristics and Test methods in accordance with EN 300 440-2 V1.4.1 (2010-8) - Electromagnetic
compatibility and radio spectrum matters (ERM); short range devices; radio equipment to be used in the
1GHz to 40GHz frequency range
Low Voltage Directive: Directive 2014/35/EU (Electrical Equipment designed for use within certain voltage
limits) of 26th February 2014.
EN62368-1: 2014 Audio/video, information and communication technology equipment. Safety requirements
European Waste Electronic Equipment Directive 2002/96/EC
Waste electrical products should not be disposed of with household waste. All electronic products with the
WEEE logo must be collected and sent to approved operators for safe disposal or recycling. Please recycle
where facilities exist. Many electrical/electronic equipment retailers facilitate “Distributor Take-Back
scheme”for household WEEE. Check with your Local Authority or electronic retailers for designated
collection facilities where WEEE can be disposed of for free.

7
Contact Information
Panorama Antennas Ltd
Panorama Antennas Inc
[e-mail]
61 Frogmore, Wandsworth, London, SW18 1HF
[phone]
USA
[e-mail]
[phone]
1551 Heritage Parkway, Suite 101, Manseld, TX, 76063
Panorama Antennas Pty Ltd
Panorama Antennas SAS
Unit 1, 5 Jaggs Way, Kardinya, WA 6163
Australia
[phone]
[email protected]
France
[email protected]
[phone]
16 Allée des Acacias, 33700 Mérignac
Panorama Antennas Pte Ltd
Singapore
[email protected]
[phone]
Space@ Tampines, 18 Tampines Industrial Crescent, 528605
Panorama Antennas Ltd
Germany
[email protected]
[phone]