Paradyne Hotwire 8510 User manual

1
8510-A2-GZ40-20 January 2000
Hotwirer8510 RADSL Card
Installation Instructions
Document Number 8510-A2-GZ40-20
January 2000
What is a Hotwire 8510 RADSL Card?
A HotwirerRate Adaptive Digital Subscriber Line (RADSL) card is a circuit card
assembly (CCA) that contains four ports, an Ethernet interface to the Network
Service Provider (NSP), and a processor. The processor controls the RADSL
ports and forwards the packet traffic to and from the Ethernet and RADSL
interfaces.
When the 8510 RADSL card is used in a Hotwire 8600/8610/8800/8810 Digital
Subscriber Line Access Multiplexer (DSLAM) or 8820 GranDSLAM chassis and
connected to a Hotwire 5620 Remote Termination Unit (RTU) or 6371 DSL
Router, it provides high-speed Internet or intranet access over traditional
twisted-pair telephone wiring.
Product Documentation on the World Wide Web
We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the
waste of surplus printing. It also helps us maintain competitive prices for our
products.
Complete documentation for this product is available at www.paradyne.com.
Select Library →Technical Manuals →Hotwire DSL & MVL Systems.
Select the following documents:
8000-A2-GB22
Hotwire Management Communications Controller (MCC) Card,
IP Conservative, User’s Guide
8000-A2-GB26
Hotwire MVL, RADSL, and Packet SDSL Cards, Models 8310/8312,
8510/8373/8374, and 8343/8344, User’s Guide
8000-A2-GB27
Hotwire Network Design Guide: Bridged Model

2 8510-A2-GZ40-20
January 2000
Contact your sales or service representative to order a paper copy of a Paradyne
document:
HWithin the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
HOutside the U.S.A., call 1-727-530-8623
8510 RADSL Card Installation Planning
HEach Hotwire chassis is shipped with one of the following installation
documents:
Document Number Document Title
8600-A2-GN20 Hotwire 8600 Digital Subscriber Line Access
Multiplexer (DSLAM) Installation Guide
8610-A2-GN10 Hotwire 8610 DSLAM Installation Instructions
8800-A2-GN21 Hotwire 8800 Digital Subscriber Line Access
Multiplexer (DSLAM) Installation Guide
8810-A2-GN11 Hotwire 8810 DSLAM Installation Instructions
8820-A2-GN20 Hotwire 8820 GranDSLAM Installation Guide
HRefer to one of the above installation documents to:
— Install and set up the Hotwire DSLAM or GranDSLAM chassis
— Install the Hotwire 8510 RADSL Card
— Connect cables
HAfter the RADSL card is installed, there are configuration procedures that
must be performed before you can begin to use the RADSL cards for Internet
or intranet connectivity. Refer to theHotwire MVL, RADSL, and Packet SDSL
Cards, Models 8310/8312, 8510/8373/8374, and 8343/8344, User’s Guide for
detailed configuration procedures. Access this document using the
instructions on page 1.

3
8510-A2-GZ40-20 January 2000
Installing the 8510 RADSL Card
"Procedure
To install the Hotwire 8510 RADSL Card in a Hotwire chassis:
1. If there is a filler plate covering the slot, remove it.
2. Insert the card into the card guides of the slot on the chassis. For the
8600/8610 DSLAM, ensure that the components are facing up.
3. Carefully slide the card into the slot. Gently, but firmly, push the card until it
engages its mating connectors on the backplane.
4. Verify that the OK SYSTEM indicator on the card’s faceplate is ON (green).
If not, refer to the appropriate chassis installation document.
5. Secure the card by fastening the screws on each end of the faceplate. This is
required to maintain proper gasket pressure on the faceplate as well as
proper air flow.

SYSTEM
OKAlrm
Test
TXRXColl
1234
ETHERNET
DSL PORT
RADSL
8510
98-15888
4 8510-A2-GZ40-20
January 2000
8510 RADSL Card LEDs
The following table describes the meaning and states of the LEDs on the Hotwire
8510 RADSL card faceplate.
Type LED LED is . . . Indicating . . .
SYSTEM OK Green,
Winking
Green, On
Off
Card functioning normally. Winking describes a
recurring pulse when the LED is ON longer than
OFF at a ratio of approximately 10:1.
8510 RADSL card failure. System processing
functions have stopped.
No power to card.
Alrm Yellow, On
Off
Alarm is present on 8510 RADSL card. Ethernet
(eth1) interface is not being detected.
No alarms.
Test Yellow, On
Off
Test in progress.
No tests.
ETHERNET TX Green,
Blinking
Off
Packets are being transmitted. LED blinks on
and off about five times per second.
Inactive.
RX Green,
Blinking
Off
Packets are being received. LED blinks on and
off about five times per second.
Inactive.
Coll Off
Yellow,
Blinking
Normal operation.
A collision has been detected. LED blinks on
and off about five times per second.
DSL PORT 1, 2, 3,
and 4 Green, On
Off
Yellow, On
DSL link is up.
DSL link is down or disabled.
DSL handshake and PPP startup in progress.

5
8510-A2-GZ40-20 January 2000
8510 RADSL Card Technical Specifications
Specifications Criteria*
Size Length: 10.4 inches (26.42 cm)
Height: 11.15 inches (28.32 cm)
Width: 0.8 inches (2.03 cm)
Weight Approximately 1.4 lbs. (0.64 kg)
Approvals
Safety Certifications Refer to the equipment’s label for approvals on product.
Power The RADSL card contains a dc-to-dc converter that
requires –48V power input. The –48V power is distributed
through the Hotwire chassis backplane.
Maximum Power Dissipation = 18 watts
Physical Environment
Operating temperature
Storage temperature
Relative humidity
Shock and vibration
32°to 122°F (0°to 50°C)
–4°F to 158°F (–20°C to 70°C)
5% to 85% (noncondensing)
Withstands normal shipping and handling.
* Criteria of technical specifications are subject to change without notice.

6 8510-A2-GZ40-20
January 2000
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor
directly for any help needed. For additional information concerning warranty,
sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
HInternet: Visit the Paradyne World Wide Web site at www.paradyne.com.
(Be sure to register your warranty at www.paradyne.com/warranty.)
HTelephone: Call our automated system to receive current information by fax
or to speak with a company representative.
—Within the U.S.A., call 1-800-870-2221
—Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail
them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N.,
Largo, FL 33773, or send e-mail to [email protected]. Include the
number and title of this document in your correspondence. Please include your
name and phone number if you are willing to provide additional clarification.
Trademarks
Hotwire is a registered trademark of Paradyne Corporation. MVL is a trademark
of Paradyne Corporation. All other products and services mentioned herein are
the trademarks, service marks, registered trademarks, or registered service
marks of their respective owners.
*8510-A2-GZ40-20*
*8510–A2–GZ40–20*
Copyright E2000 Paradyne Corporation. Printed in U.S.A.