PASGAO S1500 User manual

Brand name:PASGAO
FCC ID:2ACD8S1500

Faceplate Introduction
①power supply/volume button
Turn the button to “off”, the bluetooth
module is closed and power is off. Spin the
button clockwise, bluetooth module will
be on and volume will get high and higher.
②Status showing button
Green light on, means the power supply
of bluetooth module is on. Red light
flickers quickly, means player (cell phone
bluetooth) is not connected to the module.
Red light flickers slowly (flicker about every
2 seconds) means it is playing. Red light off
(only green light), means the playing is
suspended or connection is finished & the
module is ready to play.
③Press this button, it will play the former song.
④Press this button, it will change playing condition.
When it is playing, it will suspend if pressing the
button. When it doesn’t play, it will continue to
play if pressing the button.
⑤Press this button, it will play next song.
Notes:In order to avoid sonic boom when
skipping or suspending playing, there will be a bit
delay after pressing the button. The softwares of
some mobile phones are not so suitable for the
button controlling of bluetooth panel. Sometimes it
even does not operate normally, which mainly
cause d by software incompatibility. Pls try to install
other playing software on your mobile phone.
When the mobile phone is connected with
bluetooth module for the first time, there may exist
an occasion that the mobile phone can not search
bluetooth device. The main reason for this occasion
is that some mobile must search on-hook button
first, and then it will be connected normally. To
solve this probem, please press the playing button
for a long time , and click “searching device” in
setting functions of your mobile phone bluetooth,
till bluetooth device is searched. The bluetooth will
be connected when clicking bluetooth device.

Module Instructions
Firstly, turn o the power supply of bluetooth module. The green light on and red light
flickers quickly means module is ready to be connected. Then open the bluetooth of your
mobilephone (please make sure there is bluetooth module in your mobile phone, and it
supports bluetooth headset ). Find bluetooth in the setting function of your mobile phone,
and start bluetooth function. Then click “searching device ”in bluetooth setting. After the
bluetooth find “AMPLIVOX S1500” ( this name can be produced according to customer’s
requirements, and it should be settled during production. We will omit introducing this
function in following passage), then click
“AMPLIOX S1500”, then devices will be connected. When they are connected successfully,
you can read “connected already” below “AMPLIOX S1500” on your phone. Or you can
check if the status showing button is green. Thus devices finish pairing and being
connected.
when the bluetooth module is connected with bluetooth devices, you can start to play
music on mobile phone. You can adjust the volume button to reach your requirements.

Connectors sequence

0
Technical Data
Bluetooth version: 3.0
Working Voltage: 8-12V
Working current:60-80mA( not paired),45-65(paired)
Standby current: 40-70mA(not paired)
Output electrical level: -8.2 dBV)(390mVrms)
Frequency response:20hz-18KHZ
S/N:＞68dB
THD:0.05%(1kHZ)
S1500Device name:

"Attention‐LimitedModularApproval
ThisRFModuleisstrictlylimitedtointegrationintobatterypoweredhostdevices.Integration
intodevicesthataredirectlyorindirectlyconnectedtoAClinesmust addedviaClassII
PermissiveChange."

(OEM)Integratorhastoassurecomplianceoftheentireend‐product incl.theintegratedRF
Module.Additionalmeasurements(15B)and/orequipmentauthorizations(e.gVerification)may
needtobeaddresseddependingonco‐locationorsimultaenous transmissionissuesifapplicable.

Integratorisremindedtoassurethattheseinstallationinstructions willnotbemadeavailableto
theend‐userofthefinalhostdevice.

WiththedocumentedmaxoutputpowerthisRFModulemeetstheFCCSARExemption‐so it
comply with any applicable RF exposure requirements in its final configuration.

TheRFModuleispoweredbybattery,theantennaisPCBantennaandtheantennagainis0dBi

Thefinalhostdevice,intowhichthisRFModuleisintegrated"hastobelabelledwithanauxilliary
lablestatingtheFCCIDoftheRFModule,suchas"ContainsFCCID:2ACD8S1500"."

Thisdevicecomplieswithpart15oftheFCCrules.Operationissubjecttothefollowingtwo
conditions:
(1)thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycause
undesiredoperation.

"Changesormodificationstothisunitnotexpresslyapprovedbytheparty
responsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment."
This BT Module must be always marketed as it is mounted on this PCB with the dedicated onboard
antenna.
The BT module itself may not be integrated into any other application without C2P.