Patio Premier 101009 User manual

Durango 32" Square Outdoor Fire Pit
Sku: 101009
Care InstructionsCare Instructions
Most metal outdoor furniture is finished with paint, varnish, or powder coating to
prevent rust. This product is quality built and made to last. The frame structure of
this unit is made of powder-coated steel extrusion and under normal use, should
resist rusting. Should rusting however, occur, we suggest using a steel brush on the
affected area followed by a spray coating of popular anti-rust paint.
· Wash all frames with a solution of mild soap (like dish soap) and water.
· Rinse with clean water and dry with a soft absorbent cloth towel to remove buildup
of dirt particles.
· DO NOT clean with abrasive materials of solvents to avoid scratching or damaging
your set.
· Store furniture in an upright position to prevent water building up in frames, as this
will cause corrosion and freeze damage in cold climates.
· Consider covering your furniture when not in use for long periods of time (and
during bouts of inclement weather).

Package Contents
A B C D
E F
K L
Corner Post Mantle Square Bowl Log Grate
Ladder Frame M6 X 12mm BoltMesh Lid Connecting Plate
x4 x4
x1 x4
G
x4
H1
x16
H2 I Lid Ring Protective CoverM6 X 15mm Bolt M6 X 12mm Bolt
x8 x8
J
x1
K
x1x1 x1
L M GrillPoker Allen Wrench (M4)
x1 x1
N
x1
x1 x1
This fire pit is intended for Outdoor Use Only! DO NOT use on wooden decks.
This fire pit is intended to Burn Wood Logs Only! DO NOT burn coal, leaves or other combustible materials in the fire pit.
NOT for use by children. Keep children and pets away from the fire pit.
Fire pits is hot, use with caution. NEVER touch hot fire pit with bare hands.
NEVER leave burning fire pit unattended and always extinguish fire completely before leaving the fire pit.
Maintain a minimum of 5 FT from any structure!
DO NOT use near flammable or combustible objects or materials.
LOG GRATE is NOT intended for cooking and SHOULD NOT be used for this purpose.

4
5
Tighten all the bolts accordingly with Allen wrench (N) until all pieces fit together securely. Then turn the
assembled fire pit frame over so that it sits securely (legs down) on a flat surface. Place square bowl (C) on
the base and put log grate (N) in the square bowl (C). Then place grill (D) in the square bowl (C). ( See figure
below)
Affix lid ring (J) to the mesh lid (E) by screwing the lid ring into the upper hole of the mesh lid. Then place
the mesh lid on the square bowl. ( See figure Below)
6Operation Instructions
Place wood logs on grate light with match. DO NOT overload logs.
Please use poker (L) when handling.
We do not recommend pouring water over the fire unless necessary The fire should be allowed to expire
on its own.
1
2
Assembly Instructions
Place mantle (B) on soft, even clean surface with the groove side upwards to form a square. Connect each
by using bolts (H1). (See figure below) Loosely tighten all bolts, complete bolt tightening process after four
mantle parts are connected.
Attach connecting plates (F) to corner posts (A) by using bolts (I). Tighten the bolts (I) with an Allen
wrench (L). Then attach the corner posts (A) by installing connecting plates (F) to the mantles (B) by using
bolts (H2). (See figure below)
3Mount ladder frames (G) to the studs pre-installed on the
corner posts (A), then attach the ladder frames (G) to the
corner posts (A) by using bolts (H1). (See figure below)
H1
H2 H2
A
A
F
F
B
H1
N
A
C
J E
G
D
H1
B