Patriot Docks PN10474 User manual

www.patriotdocks.com
PN10474
Single Watercra Bunk Li
General Info:
Liing Capacity: 1200 Lbs.
Frame Length: 96” Frame width: 60” or 72” Beam: 50” (64” with extensions)
Unit Weight: 80 lbs.
Shore End Adjustability: 4” to 16” Drop Leg adjustment
Lake End Adjustability: 18” of screw travel, 4” to 16” of Drop Leg adjustment.
Mulple mounng locaons on the Screw Jack mounng ange.
Does NOT include bunk material. 2x4” or 2x6” mbers are recommended.
Includes manual speed crank handle. Screw Jacks can also be operated using
a 19mm (3/4”) socket and cordless drill.

www.patriotdocks.com
Part Idencaon
Item # Item Quanty Descripon
1Aluminum Screw Jack, 24” 2Aluminum Screw Jack assembly supports the lake end of the li
2Drop Leg Assembly (two piece) 4Drop Leg assembly, includes vercal tube and at base
3Aluminum Backer Plate , Screw Jack 2Used to clamp the Screw Jacks in place
4Bunk Bracket Assembly (two piece) 4Supports bunk material, align with hull of boat
5Steel Backer Plate, Bunk Bracket 4Used to clamp the Bunk Bracket in place
6Li Tube, Frame 1Supports the lake end of the li using two Screw Jacks with Drop Legs
7Staonary Tube, Frame 1Supports the shore end of the li using two Drop Leg assemblies
8Stringer Tube, Frame 2Joined together using the Splice Tube
9Splice Tube, Frame 1Used to join the two Stringer Tubes into one length
10 Aluminum Angle Bracket 2”x2”, Frame 4Joins Stringer Tubes to the Li and Staonary Tubes
11 Manual Speed Crank 1Manual handle used to operate the aluminum screw jack.
1
2
2
3
4
5
6
7
8
9
10
11
Fastener Quanty Descripon
M10x50mm 4Bunk Bracket assembly
M10x60mm 16 Frame assembly
M10x100mm 8Bunk Bracket mounng
M10 Nylon Bolt 4Used to mount Bumpers to Screw
Jacks.
M12x70mm 8Drop Leg assembly and installaon
Pan Head Screw 8Used to mount bunk material to
the Bunk Support assembly

www.patriotdocks.com
Step One
Step Two
The rst step is to join the two Stringer Tubes together using the
Splice Tube. Secure in place using two M10x50mm bolt/nut.
Install the four 50mm x 50mm angles to the opposite ends of the as-
sembly Stringer Tube. Secure using M10x50mm bolt/nut.
Splice Tube ts inside the
Stringer Tubes.
Fasten the stringer tube assembly to the Staonary Tube and Li
Tube using four M10x50mm bolts.

www.patriotdocks.com
Step Three
Aer the frame has been assembled, the Drop Legs can be added to
the welded sleeves on the Staonary Tube and set to the desired
height. Next, the aluminum screw jacks are mounted to the Li Tube
using the aluminum backer plate and M10x80mm bolt/nut. Drop Leg
bases are used in the aluminum screw jacks as well. Set desired drop
leg height and secure using M12x70mm bolt/nut
Oponal: Splice Tubes can be added to each end of the Li Tube to
increase the overall width of the li.

www.patriotdocks.com
Step Four
Install Bunk Bracket vercals to both the Staonary and Li Tubes,
the spacing between the bunk supports should be consistent. Secure
the bunk supports using the steel backer plate and M10x100mm bolt/
nut.
Adjust the side to side spacing between the bunk support vercals to
properly support the boat hull.
Align the bunk material with the Bunk Supports and mark the
mounng locaons on the bunk material. The bunk mounng channel
can then be mounted to the bunk material at the marked locaons
and is then ready to be installed on the li.
Adjust spacing in ancipaon to
match the watercra’s hull.

www.patriotdocks.com
Electric Remote Opon:
Operate your manual boat li while in the boat, on the dock or in the lake with this 12 volt DC remote control
electric motor kit. Turn the boat li into a kayak or pwc launch using the remote control.
This kit includes two electric motor bracket assemblies, a control box, a baery mounng assembly, heavy duty
waterproof underwater SO cable and a remote control. Baery and baery box not included.
Simple remove the jack top nut and install the motor assembly to each screw jack, route the SO cables to the
motors and connect power. Email [e-mail].