stellar labs Slider50 User manual

Slider50 Hooklift
Owner’s Manual
Stellar Industries, Inc.
190 State Street
PO Box 169
Garner, IA 50438
800-321-3741
Fax: [phone]
www.stellarindustries.com
Subject to Change without Notification.
© 2021 Stellar Industries, Inc.
Rev 1
PN 89561
Installation • Assembly Drawings • Parts

Page ii | Stellar®Slider50 Owner’s Manual
Slider Hooklift Manual Revisions
Date of Revision Section Revised Description of Revision

Stellar®Slider50 Owner’s Manual | Page iii
Table of Contents
Introduction iv
Serial Tag Location...................................................................................................................................................................... v
Chapter 1 - Specifications...............................................................................................................................................................1
Slider50 Specifications................................................................................................................................................................ 1
Slider50 Latch Locations for Skid Compatibility....................................................................................................................... 2
Slider50 Grease Zerk Locations.................................................................................................................................................. 2
Chapter 2 - Installation ....................................................................................................................................................................3
General Installation .................................................................................................................................................................... 3
Installer Notice ......................................................................................................................................................................... 3
Torque Data Chart .................................................................................................................................................................. 4
Installation Note....................................................................................................................................................................... 5
Step 1: Set the hooklift onto the truck frame........................................................................................................................... 5
Step 2: Bolt Tie-Down Angles to Mounting Plates.................................................................................................................... 6
Step 3: Drill Mounting Holes into Frame Rail............................................................................................................................. 7
Step 4: Bolt Tie-Down Angles to Truck Frame........................................................................................................................... 7
Mounting Kit Overview - PN 75258............................................................................................................................................ 8
Step 5: Install bumper. ................................................................................................................................................................ 9
Step 6: Install tarper tower (If applicable). .............................................................................................................................. 9
Step 7: Install hydraulic reservoir and valve bank................................................................................................................... 9
Reservoir Assembly (2 Section Cable Controls) - PN 86464.............................................................................................. 10
Reservoir Assembly (3 Section Cable Controls) - PN 86474.............................................................................................. 11
Reservoir Assembly (2 Section Air Controls) - PN 86468 .................................................................................................... 12
Reservoir Assembly (3 Section Air Controls) - PN 86478 .................................................................................................... 13
Reservoir Subassembly - PN 86006....................................................................................................................................... 14
Step 9: Install PTO and pump. ................................................................................................................................................. 16
Step 10: Route hydraulic hoses. .............................................................................................................................................. 17
Hose Kit - PN 75764 (Fixed Hook Height Models) ............................................................................................................... 17
Hose Kit - PN 84957 (Adjustable Hook Height Models)...................................................................................................... 18
Power Beyond VDM8 Valve ................................................................................................................................................. 19
Step 11: Route Electrical Components .................................................................................................................................. 20
Step 12: Install cab and PTO controls. .................................................................................................................................... 21
Cable Controls ...................................................................................................................................................................... 21
Air Controls............................................................................................................................................................................. 22
Step 13: Install Hoist Up Light Sensor - PN 83115 .................................................................................................................... 23
Step 14: Install mud flaps and fenders.................................................................................................................................... 24
Poly Tandem Fender Assembly - PN 58217......................................................................................................................... 24
Steel Tandem Fender Assembly - PN 100617 ..................................................................................................................... 25
Step 15A: Apply Hooklift Assembly Decals ............................................................................................................................ 26
Step 15B: Apply Chassis Decals............................................................................................................................................... 27
Step 16: Fill reservoir and activate hydraulic flow................................................................................................................. 28
Step 17: Operate hooklift......................................................................................................................................................... 28
Chapter 3 - Assembly Drawings ................................................................................................................................................... 29
Base Assembly - PN 72638........................................................................................................................................................ 29
Dump Assembly - PN 72640 ..................................................................................................................................................... 30
Latch Assembly - PN 74922 ...................................................................................................................................................... 31
Rear Roller Assembly (Optional) - PN 77274 .......................................................................................................................... 32
Secondary Assembly - PN 72964............................................................................................................................................. 33
Wear Pads 34
Main Cylinder Assembly - PN 74924........................................................................................................................................ 35
Jib Assembly (54” Hook Height) - PN 75315 ........................................................................................................................... 36
Jib Assembly (61.75” Hook Height) - PN 72966 ...................................................................................................................... 37
Jib Assembly (54/61.75” Hook Height) - PN 73912 ................................................................................................................ 38
Jib Assembly (54/61.75” Hook Height) - PN 117668 .............................................................................................................. 40
Hose Track - PN 74509............................................................................................................................................................... 41
Slider50 Cylinder Assemblies.................................................................................................................................................... 42
Valve Bank Parts Drawing ........................................................................................................................................................ 43
Pintle Bumper - PN 76381 ......................................................................................................................................................... 44
Toolbox Assembly - PN 8480..................................................................................................................................................... 45
Toolbox Assembly - PN 10401................................................................................................................................................... 45
Toolbox Assembly - PN 10402................................................................................................................................................... 45

Page iv | Stellar®Slider50 Owner’s Manual
Introduction
A copy of this manual is provided with every hooklift and can be found in the hard plastic
manual case that is installed on the chassis. A copy of this manual shall remain with the
hooklift at all times.
Throughout the manual, three signal words will be used to bring attention to important
items:
A NOTICE signal word indicates a practice not related to physical injury.
A WARNING signal word indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
A DANGER signal word indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Information contained within this manual does not cover operation, maintenance, or trou-
bleshooting. Please refer to the General Slider Hooklift Manual for details on these items.
This manual is not binding. Stellar Industries, Inc. reserves the right to change, at any time,
any or all of the items, components, and parts deemed necessary for product improve-
ment or commercial/production purposes. This right is kept with no requirement or obliga-
tion for immediate mandatory updating of this manual.
In closing:
If more information is required or technical assistance is needed, or if you feel that any part
of this manual is unclear or incorrect, please contact the Stellar Customer Service Depart-
ment by phone at 800-321-3741 or email at [email protected].
WARNING
NOTICE
DANGER
For Technical Questions, Information, Parts, or Warranty, Call Toll-Free at
800-321-3741
Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST
Or email at the following addresses:
Technical Questions, and Information [email protected]
Order Parts [email protected]
Warranty Information [email protected]

Stellar®Slider50 Owner’s Manual | Page v
The serial tag should be located on the right side (passenger side) of the base assembly:
FOR SERVICE ON THIS EQUIPMENT
CONTACT:
STELLAR INDUSTRIES, INC.
190 STATESTREET, GARNER, IA 50438
641-923-3741
800-321-3741
4214
®
35234
ProudlyDesigned
andManufactured
inthe USA by
MODELNO. SERIALNO.
DATE
MADEIN THE U.S.A. BY STELLAR INDUSTRIES, INC. PN C5942
THEFOLLOWING U.S. OR FOREIGN PATENTSMAY APPLY:
U.S.PATENTS
6,749,389 6,558,104 5,427,495
5,108,247 6,065,942 5,082,417
CANADIANPATENTS
6,749,389
5,108,247
WARNING
25627 - Rev B
Moving parts can crush
and cut.
Keep hands and arms
clear when operating
equipment.
Crush Hazard
DANGER
Electrocution Hazard
Death or serious injury will result from
inadequate clearance if hooklift, load,
or vehicle becomes electrically
charged.
• Maintain safe clearance from high
voltage power sources.
• Never approach vehicle or load if
equipment is near a high voltage
power source.
55832 - RevA
Serial Tag Location
MODEL NO. SERIAL NO.
DATE
MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC.
PN C5942
®
PATENT INFORMATION
http://www.stellarindustries.com/ip

Page vi | Stellar®Slider50 Owner’s Manual
This page intentionally left blank.

Stellar®Slider50 Owner’s Manual | Page 1
L
K
A
G
J
EB
C
C
D
H
I
Chapter 1 - Specifications
54” (1,372mm) Fixed Hook Height 61.75” (1,569mm) Fixed Hook Height 54” (1,372mm) to 61.75” (1,569mm)
Adjustable Hook Height
Lifting Capacity 42,500 (19,278 Kg) 50,000 lbs (22,680 kg) 42,500 lbs - 50,000 lbs (19,278 kg - 22,680
kg)
Dumping Capacity 50,000 lbs (22,680 kg) 50,000 lbs (22,680 kg) 50,000 lbs (22,680 kg)
A Dump Angle 51° 51° 51°
B Lowest Hook Height 46” (1,169 mm) 39.25” (997 mm) 46” or 39.25” (1,169 or 997 mm)
C Effective Length 192” to 238” (4,877 mm to 6,046 mm) 192” to 238” (4,877 mm to 6,046 mm) 192” to 238” (4,877 mm to 6,046 mm)
D Truck Frame Height 45” (1,143 mm) 45” (1,143 mm) 45” (1,143 mm)
E Hooklift Height 57” (1,448 mm) 57” (1,448 mm) 57” (1,448 mm)
G Hooklift Length 247.56” ( 6,288 mm) 247.56” ( 6,288 mm) 247.56” ( 6,288 mm)
H Hooklift Center of Gravity 102” (2,591 mm) 102” (2,591 mm) 102” (2,591 mm)
I Chassis Cab to Trunion 182” to 202” (4,623 to 5,131 mm)*** 182” to 202” (4,623 to 5,131 mm)*** 182” to 202” (4,623 to 5,131 mm)***
J Max. Height When Loading 179.38” (4,557 mm) 183.68” (4,666 mm) 179.38” or 183.68” (4,557 or 4,666 mm)
K Longest Body When Dumping 288” (7,315 mm) 288” (7,315 mm) 288” (7,315 mm)
L Max. Height When Dumping 281.50” (7,150 mm) 286.38” (7,274 mm) 281.50” or 286.38” (7,150 or 7,274 mm)
Maximum Operating Pressure 4,500 psi (31 MPa) 4,500 psi (31 MPa) 4,500 psi (31 MPa)
Hydraulic Flow 24 gpm (91 lpm) 24 gpm (91 lpm) 24 gpm (91 lpm)
Shipping Weight 5,630 lbs (2,554 kg) 5,650 lbs (2,563 kg) 6,010 (2,726 kg)
Shipping Dimensions (LxWxH) 248.81” x 52.88” x 75.75” 248.81” x 52.88” x 83.50” 248.81” x 52.88” x 75.75”
Minimum Truck GVWR 54,000 lbs (24,494 kg) 54,000 lbs (24,494 kg) 54,000 (24,494 kg)
Load Angle w/Shortest Body Length 41° 43° 41° or 43°
Recommended Container Lengths* 16’ to 20’ (4.9 to 6.1 m) 16’ to 20’ (4.9 to 6.1 m) 16’ to 20’ (4.9 to 6.1 m)
Recommended Flatbed Lengths** 16’ to 22’ (4.9 to 6.7 m) 16’ to 22’ (4.9 to 6.7 m) 16’ to 22’ (4.9 to 6.7 m)
*Assumes 2 ft. overhang
**Assumes 3 ft. overhang (May require bumper options)
***Weight Distribution Required
Slider50 Specifications
Cylinder Cycle Times:
Main Lift Cylinder Full Extend 20 seconds
Main Lift Cylinder Full Retract 48 seconds
Note: Times measured with hydraulic system producing 24GPM and an empty container.

Page 2 | Stellar®Slider50 Owner’s Manual
PN 97430
Slider50 Latch Locations for Skid Compatibility
QTY. 2
QTY. 2
QTY. 2
QTY. 2 - BOTH ENDS OF SLIDE CYLINDER
QTY. 2
QTY. 2
QTY. 2
QTY. 2
QTY. 2
Slider50 Grease Zerk Locations
PN 97462

Stellar®Slider50 Owner’s Manual | Page 3
Chapter 2 - Installation
Installer Notice
According to Federal Law (49 cfr part 571), each final-stage manufacturer shall complete the vehi-
cle in such a manner that it conforms to the standards in effect on the date of manufacture of the
incomplete vehicle, the date of final completion, or a date between those two dates. This require-
ment shall, however, be superseded by any conflicting provisions of a standard that applies by its
terms to vehicles manufactured in two or more stages.
Therefore, the installer of Stellar®Hooklifts is considered one of the manufacturers of the vehicle.
As such a manufacturer, the installer is responsible for compliance with all applicable federal and
state regulations. They are required to certify that the vehicle is in compliance with the Federal
Motor Vehicle Safety Standards and other regulations issued under the National Traffic and Motor
Vehicle Safety Act.
Please reference the Code of Federal Regulations, title 49 - Transportation, Volume 5 (400-999), for
further information, or visit http://www.gpoaccess.gov/nara/index.html for the full text of Code of
Federal Regulations.
General Installation
This chapter is designed to serve as a general guide for the installation of a Stellar®Slider65
Hooklift. Each installation is considered unique so certain portions of this chapter may or
may not apply to your direct application. If a question should arise during the installation
process, please contact Stellar Customer Service at [phone].
PTO and Pump installation instructions are provided by the corresponding manufacturers.
For more information on which PTO and Pump fit your application, please contact your
local Stellar Distributor or Stellar Customer Service.
Do not install this hooklift on a chassis not capable of handling the loads
imposed on it. Failure to do so may result in serious injury or death.
Do not weld or drill holes into the side wall of the base tubes.
Hooklift Mounting and Assembly
Study names and locations of the parts and familiarize yourself with the hooklift before
starting the assembly . Reading the step-by-step instructions that follow will be helpful.
Assembly
Select an area for assembly that will be large enough to accommodate the completed
unit. The surface of the work area should be as level as possible. Use the proper hand
tools to ensure proper bolt tightness. Refer to the torque data chart in this chapter for the
recommended torque values for different sizes of bolts.
Model Number
Know the model number of the Stellar®Hooklift being mounted. Use this model number
whenever referring to the assembly or parts listing pages. The number is stamped on the
name plate which is located on the front frame member.
WARNING
NOTICE

Page 4 | Stellar®Slider50 Owner’s Manual
When using the torque data in the
chart, the following rules should be
observed:
• Bolt manufacturer’s particular
specifications should be consulted
when provided.
• Flat washers of equal strength
must be used.
• All torque measurements are giv-
en in foot-pounds. To convert to
inch-pounds, multiply by 12.
• Torque values specified are for
bolts with residual oils or no special
lubricants applied. If special lubri-
cants of high stress ability, such as
Never-Seez compound graphite
and oil, molybdenum disulphite,
colloidal copper or white lead are applied, multiply the torque values in the charts by the
factor .90. The use of Loctite does not affect the torque values listed above.
• Torque values for socket-head capscrews are the same as for Grade 8 capscrews.
• Do not use these values if a different torque value or tightening procedure is given for
a specific application. Torque values listed are for general use only. Check tightness of
fasteners periodically.
• Sheer bolts are designed to fail under predetermined loads. Always replace shear bolts
with identical grade.
• Fasteners should be replaced with the same or higher grade. If higher grade fasteners
are used, these should only be tightened to the strength of the original.
• Tighten plastic insert or crimped steel-type lock nuts to approximately 110 percent of the
dry torque values shown in the chart below, applied to the nut, not to the bolt head.
Tighten toothed or serrated-type lock nuts to the full torque value. Note: “Lubricated”
means coated with a lubricant such as engine oil, or fasteners with phosphate and oil
coatings. “Dry” means plain or zinc plated without lubrication. Tighten lubricated bolts
to approximately 80% of dry bolts.
Size Bolt DIA Plain Plated Plain Plated Plated
(DIA-TPI) (Inches) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb) (Ft-Lb)
5/16-18 0.3125 17 13 25 18 22
3/8-16 0.3750 31 23 44 33 39
7/16-14 0.4375 49 37 70 52 63
1/2-13 0.5000 75 57 105 80 96
9/16-12 0.5625 110 82 155 115 139
5/8-11 0.6250 150 115 220 160 192
3/4-10 0.7500 265 200 375 280 340
7/8-9 0.8750 395 295 605 455 549
1-8 1.000 590 445 910 680 823
1 1/8-7 1.1250 795 595 1290 965 1167
1 1/4-7 1.2500 1120 840 1815 1360 1646
1 3/8-6 1.3750 1470 1100 2380 1780 2158
1 1/2-6 1.500 1950 1460 3160 2370 2865
GRADE 5 GRADE 8 GRADE 9
Torque Data Chart

Stellar®Slider50 Owner’s Manual | Page 5
• Visually inspect the truck and look for any potential issues. For example: Clearance
problems, cross members extending too high, insufficient room in front of the Slider for
tarpers, exhaust manifolds, etc., or insufficient room in the rear to allow for bumper se-
lection. Note: Stellar Industries recommends allowing 12” behind the start of clear truck
frame for installation of a tarping system.
• Be sure to square the Slider on the truck frame to allow for proper measurement. The
front of the hooklift needs to be at least 2.50” behind the cab or any equipment mount-
ed behind the cab. Note: On some Slider models, the jib may extend beyond the front
of the base.
Step 1: Set the hooklift onto the truck frame.
Every hooklift installation is unique. However, certain guidelines exist that apply to every
model. Listed below is a general set of chronological steps that may be followed when
installing a Stellar Hooklift. If any questions arise during the installation process, feel free to
contact your local dealer or Stellar Customer Service at 800-321-3741.
Installation Note
Truck Frame
Front of
Hooklift
Back of Truck Cab
or Mounted
Equipment
(Such as a
Tarper Tower)
At Least
2.5”

Page 6 | Stellar®Slider50 Owner’s Manual
• Bolt each tie-down angle to the underside of each mounting plate located on the out-
side of the main rails of the base (both sides):
Note: See Mounting Kit PN 75258 in this chapter for an overview of the mounting process.
Step 2: Bolt Tie-Down Angles to Mounting Plates.
Note: See torque chart at beginning of chapter
for proper bolt tightness.
ITEM PART DESCRIPTION QTY.
1 5199 CAP SCR 1.00-8X3.00 HHGR8 20
2 6294
NUT 1.00-8 HHGR8 NYLOC 20
3 6538
WASHER 1.00 SAE FLAT YELLOW GR8 40
5 75259
ANGLE FORMED 6.00X6.44X.50WX22.00
SLIDER50 MTG PC BLACK
2
6 75260
ANGLE FORMED 6.00X6.44X.50WX9.00
SLIDER50 MTG PC BLACK
6
5
6
6
6
1
3
3
2

Stellar®Slider50 Owner’s Manual | Page 7
Bolt each tie-down angle to the truck frame (both sides):
Step 4: Bolt Tie-Down Angles to Truck Frame.
Note: See torque chart at beginning of
chapter for proper bolt tightness.
3” Cap Screws3.50” Cap Screws 3” Cap Screws3” Cap Screws
ITEM PART DESCRIPTION QTY.
1 5199 CAP SCR 1.00-8X3.00 HHGR8 16
2 6294
NUT 1.00-8 HHGR8 NYLOC 20
3 6538
WASHER 1.00 SAE FLAT YELLOW GR8 40
4 12169
CAP SCR 1.00-8X3.50 HHGR8 4
4
3
23
1
• Using the tie-down castings as a guide, drill 1-1/16” holes through the truck frame as
shown:
Step 3: Drill Mounting Holes into Frame Rail.
1-1/16"

Page 8 | Stellar®Slider50 Owner’s Manual
5
6
6
6
4
1
3
3
2
3
2
3
1
ITEM PART DESCRIPTION
QTY.
1 5199 CAP SCR 1.00-8X3.00 HHGR8 36
2 6294
NUT 1.00-8 HHGR8 NYLOC 40
3 6538
WASHER 1.00 SAE FLAT YELLOW GR8 80
4 12169
CAP SCR 1.00-8X3.50 HHGR8 4
5 75259
ANGLE FORMED 6.00X6.44X.50WX22.00
SLIDER50 MTG PC BLACK
2
6 75260
ANGLE FORMED 6.00X6.44X.50WX9.00
SLIDER50 MTG PC BLACK
6
PN 75258
A
2
1
3
4
ITEM PART DESCRIPTION QTY.
145907 SWITCH REMOTE KP60 1
2 0437
CAP SCR 0.25-20X1.25 HHGR5 3
3 0340
WASHER 0.25 USS FLAT ZINC 3
4 0333
NUT 0.25-20 HHGR5 NYLOC 3
Mounting Kit Overview - PN 75258

Stellar®Slider50 Owner’s Manual | Page 9
Note: The two rear angles (PN 75260) are
not required when installing with Pintle
Bumper - PN 76381 (See bumper assembly
breakdown in Chapter 3 for details).
Mounting Kit Overview - PN 75258 continued...
• See NHTSA (National Highway
Truck Safety Administration) Regu-
lations for acceptable placement.
• Modify the truck frame as neces-
sary so that it ends 2” from the rear
of the hooklift.
Step 5: Install bumper.
2.00
See brand specific installation instructions.
Step 6: Install tarper tower (If applicable).
Step 7: Install hydraulic reservoir and valve bank.
• Before drilling and bolting to the frame, confirm adequate room for cable routing be-
tween in-cab controls and the valve bank. Note: The top of the reservoir should not be
above the truck frame.

Page 10 | Stellar®Slider50 Owner’s Manual
Reservoir Assembly (2 Section Cable Controls) - PN 86464
9
3
2
4
12
15
18
1
11
11
19
8
21
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOACTION X 1
42971 - DECAL OIL FILTER CHANGE X 1
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT 1
3
C4750 VALVE BALL 2.00 1
4
C4730 FTG 32-32 MP-HB STRAIGHT 1
524611 VB 2-SECTION VDM81
60521
WASHER 0.25 LOCK 3
70339
CAP SCR 0.25-20X2.50 HHGR5
3
860395
FTG 16-20 MFS-MAORB 90 1
927119
HOSE 0.75(78C-12-JC-JC-12-12-12-120) 1
10 10094
GAUGE OIL LF 2.5" 0-5000 BM 1
11
C4819 HOSE CLAMP 2.00 2
12 17766
HOSE SUCT 2.00 10FT 1
13 25630
FTG 10-4 MORB-FP STRAIGHT 1
14
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
15 c4903
FTG 12-12 MFS-FFSS 90 1
16 16152
FTG 10-10 MFS-MORB STRAIGHT 2
17
C2252 FTG 8-10 MFS-MORB STRAIGHT 2
18 83961
MNT KIT RSRVR 25G W/Z-BRKTS 1
19 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
20
C2142 FTG 12-12 MFS-MORB STRAIGHT 1
21
C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86464

Stellar®Slider50 Owner’s Manual | Page 11
Reservoir Assembly (3 Section Cable Controls) - PN 86474
9
3
2
4
12
15
20
11
11
19
8
1
22
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOACTION X 1
42971 - DECAL OIL FILTER CHANGE X 1
26182 - PORT RELIEF VDM8 2500 PSI X 2
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT 1
3
C4750 VALVE BALL 2.00 1
4
C4730 FTG 32-32 MP-HB STRAIGHT 1
538230
VB 3-SECT VDM8 1
60521
WASHER 0.25 LOCK 3
70339
CAP SCR 0.25-20X2.50 HHGR5 3
860395
FTG 16-20 MFS-MAORB 90 1
927119
HOSE 0.75(78C-12-JC-JC-12-12-12-120) 1
10 10094
GAUGE OIL LF 2.5" 0-5000 BM 1
11
C4819 HOSE CLAMP 2.00 2
12 17766
HOSE SUCT 2.00 10FT 1
13 25630
FTG 10-4 MORB-FP STRAIGHT 1
14
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
15 c4903
FTG 12-12 MFS-FFSS 90 1
16 16152
FTG 10-10 MFS-MORB STRAIGHT 2
17
C2252 FTG 8-10 MFS-MORB STRAIGHT 2
18
C1855 FTG 6-10 MFS-MORB STRAIGHT 2
19 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
20 83961
MNT KIT RSRVR 25G W/Z-BRKTS 1
21
C2142 FTG 12-12 MFS-MORB STRAIGHT 1
22
C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86474

Page 12 | Stellar®Slider50 Owner’s Manual
Reservoir Assembly (2 Section Air Controls) - PN 86468
9
3
2
4
12
15
18
11
11
19
8
1
21
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOACTION X 1
42971 - DECAL OIL FILTER CHANGE X 1
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT 1
3
C4750 VALVE BALL 2.00 1
4
C4730 FTG 32-32 MP-HB STRAIGHT 1
525940
VB 2-SECTION VDM8 W/AIR ACTUATORS 1
60521
WASHER 0.25 LOCK 3
70339
CAP SCR 0.25-20X2.50 HHGR5 3
860395
FTG 16-20 MFS-MAORB 90 1
927119
HOSE 0.75(78C-12-JC-JC-12-12-12-120) 1
10 10094
GAUGE OIL LF 2.5" 0-5000 BM 1
11
C4819 HOSE CLAMP 2.00 2
12 17766
HOSE SUCT 2.00 10FT 1
13 25630
FTG 10-4 MORB-FP STRAIGHT 1
14
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
15 c4903
FTG 12-12 MFS-FFSS 90 1
16 16152
FTG 10-10 MFS-MORB STRAIGHT 2
17
C2252 FTG 8-10 MFS-MORB STRAIGHT 2
18 83961
MNT KIT RSRVR 25G W/Z-BRKTS 1
19 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
20
C2142 FTG 12-12 MFS-MORB STRAIGHT 1
21
C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86468

Stellar®Slider50 Owner’s Manual | Page 13
Reservoir Assembly (3 Section Air Controls) - PN 86478
9
3
2
4
12
15
11
11
19
20
7
1
22
NOTE: ITEMS NOT SHOWN
25941 - DECAL LOADER VB VDM8 HOSE LOCATION X 1
42971 - DECAL OIL FILTER CHANGE X 1
26182 - PORT RELIEF VDM8 2500 PSI X 2
ITEM PART DESCRIPTION QTY.
186006
RSRVR ASM 25GAL K MODEL W/ TANK
TOP FILTER
1
27353
FTG 32-32 MP-MP HEX NIPPLE STRAIGHT 1
3
C4750 VALVE BALL 2.00 1
4
C4730 FTG 32-32 MP-HB STRAIGHT 1
547562
VB 3-SECTION VDM8 W/AIR ACTUATORS 1
60521
WASHER 0.25 LOCK 3
760395
FTG 16-20 MFS-MAORB 90 1
8
C2252 FTG 8-10 MFS-MORB STRAIGHT 2
927119
HOSE 0.75(78C-12-JC-JC-12-12-12-120) 1
10 10094
GAUGE OIL LF 2.5" 0-5000 BM 1
11
C4819 HOSE CLAMP 2.00 2
12 17766
HOSE SUCT 2.00 10FT 1
13 25630
FTG 10-4 MORB-FP STRAIGHT 1
14
d1435 FTG 12-10 MFS-MORB STRAIGHT 1
15 c4903
FTG 12-12 MFS-FFSS 90 1
16
C1855 FTG 6-10 MFS-MORB STRAIGHT 2
17 0339
CAP SCR 0.25-20X2.50 HHGR5 3
18 16152
FTG 10-10 MFS-MORB STRAIGHT 2
19 83961
MNT KIT RSRVR 25G W/Z-BRKTS 1
20 86168
HOSE 0.75(300PSI)-16FFSS SHORT-12FFSS
90 SHORT-7.75CL
1
21
C2142 FTG 12-12 MFS-MORB STRAIGHT 1
22
C6327 FILTER STRAINER 35GAL TF-2030 1
PN 86478

Page 14 | Stellar®Slider50 Owner’s Manual
Reservoir Subassembly - PN 86006
9
10
7
8
6
3
2
5
1
4
11
NOTE: REPLACEMENT OIL FILTER - PN 86010
ITEM PART DESCRIPTION QTY
1 C2126 MAGNETIC PLUG DRAIN 3/4" 1
2 15463
THERMO SIGHT GAUGE ZINGA SG-O5-A-T-N 1
3 73278
CAP FILL 1PSI ZINGA THREADED 1
4 13002
DECAL HYD OIL SPECIFICATION MOBIL 1
5 86007
RSRVR 25GAL K MODEL W/ TANK TOP FILTER 1
6 66656
FILTER PIPE TANK TOP 1
7 85928
FILTER TANK TOP 20 FORB 1
8 58396
GASKET RG-11 TANK TOP FILTER 1
9 0335
CAP SCR 0.38-16X1.25 HHGR5 4
10
C6353 WASHER 0.38 SAE FLAT YELLOW GR8 4
11
C4845 PLUG 0.75 NPT SQ HD BLK 1
PN 86006
NOTE: REPLACEMENT GASKET
UNDER FILTER CAP - PN 109546