Patton electronics RocketLink-G 3088/I User manual

RocketLink™-G Model 3088/I
G.SHDSL NTU
Quick Start Guide
Important —This is a Class A device and is intended for use in a light industrial environment. It is not
intended nor approved for use in an industrial or residential environment.
Part Number: 07M3088I-QS, Rev. D
Revised: February 15, 2012
Sales Office: [phone]
Technical Support: [phone]
E-mail: [e-mail]
WWW: www.patton.com

2Model 3088/I Quick Start Guide
1.0 Power up the NTU
Your NTU comes with an external AC adaptor with detachable power cord.
1.1 AC power-up
1. Connect female plug of the AC power cord to the AC adaptor provided.
2. Connect the barrel-type connector of the AC adaptor to the barrel-type power jack on the
RocketLink-G NTU.
3. Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC)
.
1.2 DC power-up
The 36-60 VDC DC to DC adapter is supplied with the DC version of the Model 3088/I. The black and red leads
plug into a DC source (nominal 48VDC) and the barrel power connector plugs into the barrel power supply jack
on the 3088/I. (See figure 1).
•This device contains no user serviceable parts. The equipment
shall be returned to Patton Electronics for repairs, or repaired
by qualified service personnel.
•The external power adapter shall be a listed Limited Power
Source. The mains outlet that is utilized to power the devise
shall be within 10 feet (3 meters) of the device, shall be easily
accessible, and protected by a circuit breaker.
•If an AC power adapter is used, ensure that the power cable
used meets all applicable standards for the country in which it
is to be installed, and that it is connected to a wall outlet which
has earth ground.
•Hazardous network voltages are present in WAN ports regard-
less of whether power to the unit is ON or OFF. To avoid electric
shock, use caution when near WAN ports. When detaching the
cables, detach the end away from the device first.
•Do not work on the system or connect or disconnect cables
during periods of lightning activity.
The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flam-
mability, and mechanical serviceability.
WARNING
CAUTION

Model 3088/I Quick Start Guide 3
Figure 1. DC Power Supply
1.3 Power-up indication
The Power and 100M Ethernet LEDs are lit while the RocketLink-G is powering up.
2.0 Configure the IP address
The RocketLink-G NTU is shipped with a factory-configured IP address assigned to the Ethernet LAN port (green
outline). The address is 192.168.200.10/24. In most cases, you must change the address to be on the same sub-
net as your PC, as described in the procedures below. If you are not sure which IP address to use for your instal-
lation, contact your network administrator.
2.1 Connect a PC and log in
1. Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port
to the RocketLink-G’s Console port (red outline) (see figure 2).
Figure 2. Connecting RocketLink
TM
-G NTU to the PC’s serial port
To Power
Supply Jack To -48VDC
Source
-Vin
+Vin
SWITCHING POWER SUPPLY MODEL : SYD1106-0505 INPUT : 36-60V 0.2A MAX OUTPUT : +5V 1.0A OUTPUT POWER : 5W MAX
S/N: G01234567890
MADE IN CHINA BY SUNNY
Black lead (-V
)
Red lead (+V)
Barrel power connector
MDI-X
Line
Ethernet
Power Console
Connect to Console port
Serial port
PC with
terminal emulator

4Model 3088/I Quick Start Guide
2. Start a HyperTerminal session on the PC using the settings:
9600 bps, 8 data bits, no parity, 1 stop bit, no flow control
3. Log in to the RocketLink-G NTU using the factory-default login (superuser) and password (superuser):
Login: superuser
Password: *********
Login successful
2.2 Modify the IP address
1. Display current IP interface settings for the RocketLink-G Ethernet LAN port.
fi ip list interfaces <enter>
IP Interfaces:
ID | Name | IP Address | DHCP | Transport
---|------|----------------|----------|--------------
1 | ip1 | 192.168.200.10 | disabled | <BRIDGE>
----------------------------------------------------
2. Modify the IP address for the LAN port according to your network requirements.
fi ip set interface ip1 ipaddress 10.10.4.10 255.255.255.0
Note The above IP address ( 10.10.4.10/24) is only an example. You must choose an IP address on the same
subnet as your PC.
3. Verify the new address is correct and save it in system boot memory.
fi ip list interfaces <enter>
fi system config save <enter>
fi

Model 3088/I Quick Start Guide 5
3.0 Connect to the local IP network
Now you can connect the RocketLink-G NTU to your local IP network and complete the remaining configuration
from your PC using a standard web browser.
Connect the RocketLink-G NTU’s Ethernet port (green) to the same Ethernet segment as your PC (see figure 3).
The front-panel Ethernet Link LED should turn on. If it does not, press the rear-panel MDI-X switch so that the
Ethernet Link LED illuminates.
You can check the connection with the ping command. For example shown in figure 3, you would ping
10.10.4.10 from a PC on the IP network.
Figure 3. Connecting the RocketLink-G to the local IP network (Model 3088/I shown)
MDI-X
Line
Ethernet
Power Console
Connect to Ethernet port Ethernet port
PC
MDI-X switch

6Model 3088/I Quick Start Guide
4.0 Log onto the web management interface
You will now access the web management graphical user interface (GUI) to configure the RocketLink-G using a
standard web browser (such as Netscape browser or Internet Explorer).
1. At your PC, open a web browser and enter the IP address you assigned to the RocketLink-G’s Ethernet
LAN port in step 2 of section 2.2 “Modify the IP address” on page 4. (In this example,
10.10.4.10.)
2. Log in to the web management home page using the username superuser and the password superuser.
Figure 4. RocketLink
TM
-G web management home page

Model 3088/I Quick Start Guide 7
5.0 Connect the G.SHDSL Port
1. Obtain single-twisted-pair cable with an RJ-11 plug connector at each end.
2. Plug one end of the cable into the (yellow) RJ-11 socket (labelled Line) on the RocketLink-G NTU.
3. Plug the other end of the cable into the RJ-11 wall socket that provides your G.SHDSL service.
4. Go to G.SHDSL > Configuration to configure the DSL port parameters.
Note If two RocketLink-G NTUs are connected back-to-back, one must be configured as Remote, the other as
Central.
5. The WAN Link LED will flash while in the process of establishing a link. The LED will be on constantly once
a valid DSL connection is established.
6.0 Additional Information
For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,
refer to the RocketLink-G 3088/I User Manual available online at www.patton.com/manuals/
3088i.pdf.
A.0 Customer and Technical Support
Toll-Free VoIP support: call sip:su[email protected] with a VoIP SIP phone
Online support: www.patton.com
E-mail support: [e-mail]—answered within 1 business day
Telephone support:
• Standard: [phone] (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to 2200 UTC/GMT)
• Alternate: [phone] (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800
UTC/GMT)
Fax: [phone] (USA) or [phone] (Switzerland)

8Model 3088/I Quick Start Guide
B.0 Compliance Information
B.1 Compliance
EMC:
• FCC Part 15, Class A
• EN55022, Class A
• EN55024
Safety:
• UL 60950-1/CSA C22.2 N0. 60950-1
• IEC/EN60950-1
• AS/NZS 60950-1
PSTN Regulatory:
• FCC Part 68
• CS-03
• AS/ACIF S043:2003
B.2 FCC Part 68 (ACTA) Statement
This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of
this equipment is a label that contains—among other information—a product identifier in the format US:
AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
The method used to connect this equipment to the premises wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by the ACTA.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-
pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with
the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the telephone company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If
the equipment is causing harm to the telephone network, the telephone company may request that you discon-
nect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-
vice commission or corporation commission for information.

Model 3088/I Quick Start Guide 9
2.3 Industry Canada Notice
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con-
firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra-
tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications
were met. It does not imply that Industry Canada approved the equipment.
This Declaration of Conformity means that the equipment meets certain telecommunications network protective,
operational and safety requirements. The Department does not guarantee the equipment will operate to the
user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to
the facilities of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. In some cases, the company’s inside wiring associated with a single line individual service
may be extended by means of a certified connector assembly (telephone extension cord). The customer should
be aware that compliance with the above condition may not prevent degradation of service in some situations.
Repairs to some certified equipment should be made by an authorized maintenance facility designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for
their own protection that the ground connections of the power utility, telephone lines and internal metallic water
pipe system, are connected together. This protection may be particularly important in rural areas.
B.4 Radio and TV Interference (FCC Part 15)
This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in
strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-
tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-
dance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable
protection from such interference in a commercial installation. However, there is no guarantee that interference
will not occur in a particular installation. If the equipment causes interference to radio or television reception,
which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-
lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,
and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and
receiver are on different branches).
B.5 EC Declaration of Conformity
Product Description: RocketLink-G NTU 3088
We certify that the apparatus identified above conforms to the requirements of Council Directive 1999/5/EC on
the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip-
ment and the mutual recognition of their conformity.
The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/.
The safety advises in the documentation accompanying the products shall be obeyed. The
conformity to the above directive is indicated by the CE sign on the device.

10 Model 3088/I Quick Start Guide
B.6 Authorized European Representative
D R M Green
European Compliance Services Limited.
Avalon House, Marcham Roadþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþþ
Abingdon,
Oxonþ OX14 1UD, UK