Patton electronics RocketLink-G 3088/I User manual

Model 3088/I
RocketLink-G G.SHDSL NTU
Getting Started Guide
Sales Office: [phone]
Technical Support: [phone]
E-mail: [e-mail]
WWW: www.patton.com
Part Number: 07M3088/I-GS, Rev. D
Revised: May 14, 2010
Important
This is a Class A device and is not intended for use in a residential environment.
Start Installation
For Quick

Patton Electronics Company, Inc.
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
Tel: [phone]
Fax: [phone]
Support: [phone]
Web: www.patton.com
E-mail: [e-mail]
Trademark Statement
The term RocketLink-G is a trademark of Patton Electronics Company. All other
trademarks presented in this document are the property of their respective owners.
Copyright © 2008-2010, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Elec-
tronics assumes no liability for errors that may appear in this document.
Warranty Information
Patton Electronics warrants all Model 3088/I components to be free from defects, and
will—at our option—repair or replace the product should it fail within one year from
the first date of shipment.
This warranty is limited to defects in workmanship or materials, and does not cover
customer damage, abuse or unauthorized modification. If this product fails or does not
perform as warranted, your sole recourse shall be repair or replacement as described
above. Under no condition shall Patton Electronics be liable for any damages incurred
by the use of this product. These damages include, but are not limited to, the follow-
ing: lost profits, lost savings and incidental or consequential damages arising from the
use of or inability to use this product. Patton Electronics specifically disclaims all other
warranties, expressed or implied, and the installation or use of this product shall be
deemed an acceptance of these terms by the user.
Note
Conformity documents of all Patton products can be viewed online at
www.patton.com under the appropriate product page.

3
Summary Table of Contents
1General information...................................................................................................................................... 14
2Initial Configuration ..................................................................................................................................... 16
3G.SHDSL config and status .......................................................................................................................... 23
4Ethernet & WAN PPP config and status....................................................................................................... 29
5System Management...................................................................................................................................... 33
6Diagnostic tools............................................................................................................................................. 40
7Contacting Patton for assistance ................................................................................................................... 42
ACompliance information .............................................................................................................................. 45
BSpecifications ................................................................................................................................................ 49
CFactory replacement parts and accessories .................................................................................................... 54
DRJ-11 non-shielded DSL port ....................................................................................................................... 56
ERJ-45 shielded 10/100 Ethernet port ........................................................................................................... 58
FRS-232 console interface pin assignments .................................................................................................... 60

4
Table of Contents
Summary Table of Contents ........................................................................................................................... 3
Table of Contents ........................................................................................................................................... 4
List of Figures ................................................................................................................................................. 8
List of Tables .................................................................................................................................................. 9
About this guide ........................................................................................................................................... 10
Audience............................................................................................................................................................... 10
Structure............................................................................................................................................................... 10
Precautions ........................................................................................................................................................... 11
Safety when working with electricity ...............................................................................................................12
General observations .......................................................................................................................................13
Typographical conventions used in this document................................................................................................ 13
General conventions .......................................................................................................................................13
1General information...................................................................................................................................... 14
RocketLink-G 3088/I overview .............................................................................................................................15
Features.................................................................................................................................................................15
2Initial Configuration ..................................................................................................................................... 16
Introduction..........................................................................................................................................................17
Power up the NTU ...............................................................................................................................................17
AC power-up ..................................................................................................................................................17
Power-up indication ........................................................................................................................................17
Configure the IP address........................................................................................................................................17
Connect a PC and log in .................................................................................................................................18
Modify the IP address .....................................................................................................................................18
Connect to the local IP network .....................................................................................................................19
Log onto the web management interface .........................................................................................................19
Connect the G.SHDSL port ...........................................................................................................................20
LED status indicators ............................................................................................................................................21
Power (Yellow) ................................................................................................................................................21
WAN LEDs ....................................................................................................................................................21
Link (Yellow) ............................................................................................................................................21
Tx (Yellow) ...............................................................................................................................................21
Rx (Yellow) ...............................................................................................................................................21
Ethernet LEDs ................................................................................................................................................21
Link (Yellow) ............................................................................................................................................21
100M (Yellow) ..........................................................................................................................................22
Tx (Yellow) ...............................................................................................................................................22
Rx (Yellow) ...............................................................................................................................................22
3G.SHDSL config and status .......................................................................................................................... 23
DSL configuration.................................................................................................................................................24

5
3088/I Getting Started Guide Table of Contents
DSL Parameters ..............................................................................................................................................24
DSL Error Monitor Configuration........................................................................................................................25
G.SHDSL Status ...................................................................................................................................................26
Run-Time Statistics ........................................................................................................................................26
DSL Line Error Counters ...............................................................................................................................27
Local Interface Error Counters ........................................................................................................................27
Clearing Error Counters .................................................................................................................................28
4Ethernet & WAN PPP config and status....................................................................................................... 29
IP configuration ....................................................................................................................................................30
PPP configuration .................................................................................................................................................30
Ethernet port configuration ...................................................................................................................................30
Ethernet Basic Port Attributes .........................................................................................................................30
Ethernet Advanced Port Attributes .................................................................................................................31
5System Management...................................................................................................................................... 33
RocketLink-G Plug ‘n’ Play ...................................................................................................................................34
Saving the configuration........................................................................................................................................35
Reset for Factory Default.......................................................................................................................................35
Console ...........................................................................................................................................................35
Backing up and restoring saved configurations ......................................................................................................36
Authentication.......................................................................................................................................................36
System Software Upgrade ................................................................................................................................37
SNTP Client and Clock Configuration .................................................................................................................38
Configuring the SNTP Client Mode Parameters .............................................................................................38
Configuring the SNTP Client General Parameters ..........................................................................................39
Configuring the system clock ..........................................................................................................................39
6Diagnostic tools............................................................................................................................................. 40
LED status monitor & definition ..........................................................................................................................41
System tools for testing..........................................................................................................................................41
Ping & Traceroute ..........................................................................................................................................41
Clearing error counters ...................................................................................................................................41
7Contacting Patton for assistance ................................................................................................................... 42
Introduction..........................................................................................................................................................43
Contact information..............................................................................................................................................43
Patton support headquarters in the USA .........................................................................................................43
Alternate Patton support for Europe, Middle East, and Africa (EMEA) ..........................................................43
Warranty Service and Returned Merchandise Authorizations (RMAs)...................................................................43
Warranty coverage ..........................................................................................................................................43
Out-of-warranty service .............................................................................................................................44
Returns for credit ......................................................................................................................................44
Return for credit policy .............................................................................................................................44
RMA numbers ................................................................................................................................................44
Shipping instructions ................................................................................................................................44

6
3088/I Getting Started Guide Table of Contents
ACompliance information .............................................................................................................................. 45
Compliance ...........................................................................................................................................................46
EMC ...............................................................................................................................................................46
Safety ..............................................................................................................................................................46
PSTN Regulatory ............................................................................................................................................46
FCC Part 68 (ACTA) Statement ...........................................................................................................................46
Radio and TV Interference (FCC Part 15) ............................................................................................................47
Industry Canada Notice ........................................................................................................................................47
CE Declaration of Conformity..............................................................................................................................48
Authorized European Representative .....................................................................................................................48
BSpecifications ................................................................................................................................................ 49
General characteristics ...........................................................................................................................................50
G.SHDSL characteristics.......................................................................................................................................50
Ethernet ................................................................................................................................................................50
Protocol support....................................................................................................................................................50
Management .........................................................................................................................................................51
10Base-T/100Base-TX interface ............................................................................................................................51
Serial connector.....................................................................................................................................................51
Diagnostics............................................................................................................................................................51
Status LEDs...........................................................................................................................................................51
Power ..............................................................................................................................................................51
WAN Link ......................................................................................................................................................51
WAN Tx ........................................................................................................................................................51
WAN Rx .........................................................................................................................................................51
Ethernet Link ..................................................................................................................................................51
Ethernet 100M ...............................................................................................................................................52
Ethernet Tx ....................................................................................................................................................52
Ethernet Rx .....................................................................................................................................................52
Power ....................................................................................................................................................................52
48 VDC power supply ....................................................................................................................................52
G.SHDSL Physical connection & Transmission Line .....................................................................................53
Line Coding ....................................................................................................................................................53
Line Interface ........................................................................................................................................................53
Environment .........................................................................................................................................................53
Dimensions ...........................................................................................................................................................53
CFactory replacement parts and accessories .................................................................................................... 54
Factory replacement parts and accessories ..............................................................................................................55
DRJ-11 non-shielded DSL port ....................................................................................................................... 56
RJ-11 non-shielded DSL port................................................................................................................................57
ERJ-45 shielded 10/100 Ethernet port ........................................................................................................... 58
RJ-45 shielded 10/100 Ethernet port.....................................................................................................................59
FRS-232 console interface pin assignments .................................................................................................... 60

7
3088/I Getting Started Guide Table of Contents
RS-232 console interface pin assignments..............................................................................................................61

8
List of Figures
1 RocketLink-G 3088/I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 Model LB510A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3 Connecting G.SHDSL NTU to the PC’s serial port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4 Connecting the G.SHDSL NTU to the local IP network (Model LB510A shown) . . . . . . . . . . . . . . . . . . . . . 19
5 G.SHDSL NTU web management home page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6 Rear view of LB510A showing DSL RJ-11 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7 Model 3088/I front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8 DSL Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9 DSL Error Monitor Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10 DSL Run-time Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
11 DSL line error counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
12 Local Interface Error Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
13 Clearing the error counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
14 Configuration of the IP address and subnet mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
15 Enabling Bridged PPP over the DSL link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
16 Ethernet performance statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
17 Top of web page for configurable Ethernet parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
18 Configurable Ethernet parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
19 Typical RocketLink Plug ‘n’ Play Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
20 Saving the configuration to non-volatile memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
21 Resetting the 3088/I to factory default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
22 Backing up and reloaded saved configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
23 Login Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
24 Upgrading software on the 3088/I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
25 Software upgrade protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
26 SNTP Client Mode Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
27 SNTP Client General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
28 SNTP Clock Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
29 Ping and Traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
30 Clearing Error Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9
List of Tables
1 General conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

10
About this guide
This guide describes installing and operating the Patton Electronics Model 3088/I G.SHDSL
RocketLink-G™ NTU.
Audience
This guide is intended for the following users:
•Operators
•Installers
•Maintenance technicians
Structure
This guide contains the following chapters and appendices:
•Chapter 1 on page 14 provides information about NTU features and capabilities
•Chapter 2 on page 16 contains an overview describing NTU operation and applications
•Chapter 3 on page 23 provides hardware installation procedures
•Chapter 4 on page 29 provides quick-start procedures for configuring the RocketLink-G NTU
•Chapter 5 on page 33 describes how to configure the RocketLink-G NTU, save the configuration, reset the
NTU to the factory default condition, and upgrade the system software
•Chapter 6 on page 40 describes the system tools that can be used to diagnose problems with the NTU
•Chapter 7 on page 42 contains information on contacting Patton technical support for assistance
•Appendix A on page 45 contains compliance information for the RocketLink-G NTU
•Appendix B on page 49 contains specifications for the NTU
•Appendix C on page 54 provides cable recommendations
•Appendix D on page 56 describes the NTU’s ports and pin-outs
•Appendix E on page 58 lists the factory configuration settings for RocketLink-G NTU
•Appendix F on page 60 provides license information that describes acceptable usage of the software pro-
vided with the RocketLink-G NTU
For best results, read the contents of this guide before you install the NTU.

11
3088/I Getting Started Guide
Precautions
Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you
become aware of potential problems. Warnings are intended to prevent safety hazards that could result in per-
sonal injury. Cautions are intended to prevent situations that could result in property damage or
impaired functioning.
Note A note presents additional information or interesting sidelights.
The shock hazard symbol and WARNING heading indicate a potential electric
shock hazard. Strictly follow the warning instructions to avoid injury caused
by electric shock.
The alert symbol and WARNING heading indicate a potential safety hazard.
Strictly follow the warning instructions to avoid personal injury.
The shock hazard symbol and CAUTION heading indicate a
potential electric shock hazard. Strictly follow the instructions to
avoid property damage caused by electric shock.
The alert symbol and CAUTION heading indicate a potential haz-
ard. Strictly follow the instructions to avoid property damage.
WARNING
WARNING
CAUTION
CAUTION

12
3088/I Getting Started Guide
Safety when working with electricity
• Do not open the device when the power cord is connected. For systems
without a power switch and without an external power adapter, line volt-
ages are present within the device when the power cord is connected.
• For devices with an external power adapter, the power adapter shall be a
listed imited Power Source The mains outlet that is utilized to power the
device shall be within 10 feet (3 meters) of the device, shall be easily
accessible, and protected by a circuit breaker in compliance with local reg-
ulatory requirements.
• For AC powered devices, ensure that the power cable used meets all appli-
cable standards for the country in which it is to be installed.
• For AC powered devices which have 3 conductor power plugs (L1, L2 &
GND or Hot, Neutral & Safety/Protective Ground), the wall outlet (or
socket) must have an earth ground.
• For DC powered devices, ensure that the interconnecting cables are rated
for proper voltage, current, anticipated temperature, flammability, and
mechanical serviceability.
• WAN, LAN & PSTN ports (connections) may have hazardous voltages
present regardless of whether the device is powered ON or OFF. PSTN
relates to interfaces such as telephone lines, FXS, FXO, DSL, xDSL, T1, E1,
ISDN, Voice, etc. These are known as “hazardous network voltages” and
to avoid electric shock use caution when working near these ports. When
disconnecting cables for these ports, detach the far end connection first.
• Do not work on the device or connect or disconnect cables during periods
of lightning activity.
This device contains no user serviceable parts. This device can only be
repaired by qualified service personnel.
This device is NOT intended nor approved for connection to the PSTN. It is
intended only for connection to customer premise equipment.
In accordance with the requirements of council directive 2002/
96/EC on Waste of Electrical and Electronic Equipment (WEEE),
ensure that at end-of-life you separate this product from other
waste and scrap and deliver to the WEEE collection system in
your country for recycling.
WARNING
WARNING
WARNING

13
3088/I Getting Started Guide
General observations
•Clean the case with a soft slightly moist anti-static cloth
•Place the unit on a flat surface and ensure free air circulation
•Avoid exposing the unit to direct sunlight and other heat sources
•Protect the unit from moisture, vapors, and corrosive liquids
Typographical conventions used in this document
This section describes the typographical conventions and terms used in this guide.
General conventions
The procedures described in this manual use the following text conventions:
Electrostatic Discharge (ESD) can damage equipment and impair
electrical circuitry. It occurs when electronic printed circuit cards
are improperly handled and can result in complete or intermittent
failures. Do the following to prevent ESD:
• Always follow ESD prevention procedures when removing and
replacing cards.
• Wear an ESD-preventive wrist strap, ensuring that it makes
good skin contact. Connect the clip to an unpainted surface of
the chassis frame to safely channel unwanted ESD voltages to
ground.
• To properly guard against ESD damage and shocks, the wrist
strap and cord must operate effectively. If no wrist strap is
available, ground yourself by touching the metal part of the
chassis.
Table 1. General conventions
Convention Meaning
Garamond blue type
Indicates a cross-reference hyperlink that points to a figure, graphic, table, or sec-
tion heading. Clicking on the hyperlink jumps you to the reference. When you
have finished reviewing the reference, click on the Go to Previous View
button in the Adobe® Acrobat® Reader toolbar to return to your starting point.
Futura bold type Commands and keywords are in boldface font.
Futura bold-italic type Parts of commands, which are related to elements already named by the user, are
in boldface italic font.
Italicized Futura type Variables for which you supply values are in italic font
Futura type Indicates the names of fields or windows.
Garamond bold type Indicates the names of command buttons that execute an action.
CAUTION

14
Chapter 1 General information
Chapter contents
RocketLink-G 3088/I overview .............................................................................................................................15
Features.................................................................................................................................................................15

RocketLink-G 3088/I overview 15
3088/I Getting Started Guide 1 • General information
RocketLink-G 3088/I overview
The Patton Electronics Model 3088/I G.SHDSL RocketLink provides high speed 2-wire connectivity to ISPs,
PTTs, and enterprise environments using Symmetrical High-data-rate Digital Subscriber Line
(G.SHDSL) technology.
The Model 3088/I provides a 10/100BaseT Ethernet interface on a shielded RJ-45 jack, the DSL on an RJ-11
jack, and the RS-232 console port on an RJ-45 jack.
As a symmetric, full-duplex NTU, the RocketLink DSL offers equal data rates in both directions over a single
twisted pair using TC-PAM modulation. Line connection is made through the RJ-11 jack. Standard versions
of Model 3088/I are powered by a UI (universal 100–240 VAC) supply.
Figure 1. RocketLink-G 3088/I
Features
•Symmetrical high data-rate DSL (G.SHDSL)
•Data rates up to 4.6Mbps in 64-kbps intervals
•10Base-T/100Base-TX Ethernet interface
•RS-232 console port for management and configuration
•Built-in testing and diagnostics
•RocketLink Plug ‘n’ Play for easy installations
•Interoperable with other Patton G.SHDSL modems
•Configurable as remote (CP) units
•Configurable as central (CO) units to operate back-to-back
•Front-panel status indicators
•CE marked

16
Chapter 2 Initial Configuration
Chapter contents
Introduction..........................................................................................................................................................17
Power up the NTU ...............................................................................................................................................17
AC power-up ..................................................................................................................................................17
Power-up indication ........................................................................................................................................17
Configure the IP address........................................................................................................................................17
Connect a PC and log in .................................................................................................................................18
Modify the IP address .....................................................................................................................................18
Connect to the local IP network .....................................................................................................................19
Log onto the web management interface .........................................................................................................19
Connect the G.SHDSL port ...........................................................................................................................20
LED status indicators ............................................................................................................................................21
Power (Yellow) ................................................................................................................................................21
WAN LEDs ....................................................................................................................................................21
Link (Yellow) ............................................................................................................................................21
Tx (Yellow) ...............................................................................................................................................21
Rx (Yellow) ...............................................................................................................................................21
Ethernet LEDs ................................................................................................................................................21
Link (Yellow) ............................................................................................................................................21
100M (Yellow) ..........................................................................................................................................22
Tx (Yellow) ...............................................................................................................................................22
Rx (Yellow) ...............................................................................................................................................22

Introduction 17
3088/I Getting Started Guide 2 • Initial Configuration
Introduction
The Model LB510A (see figure 2) has two configuration modes: RS-232 console and web page GUI software.
Figure 2. Model LB510A
The RS-232 console is used for the initial configuration of the IP address and mask. Subsequently the easiest
method is to use a standard web browser to complete the configuration.
Power up the NTU
Your NTU comes with an external AC adaptor with detachable power cord.
AC power-up
1. Connect female plug of the AC power cord to the AC adaptor provided.
2. Connect the barrel-type connector of the AC adaptor to the barrel-type power jack on the
G.SHDSL NTU.
3. Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).
Power-up indication
The Power and 100M Ethernet LEDs are lit while the G.SHDSL NTU is powering up.
Configure the IP address
The G.SHDSL NTU is shipped with a factory-configured IP address assigned to the Ethernet LAN port (green
outline). The address is 192.168.200.10/24. In most cases, you must change the address to be on the same sub-
net as your PC, as described in the procedures below. If you are not sure which IP address to use for your
installation, contact your network administrator.
Ensure that the power cable used with the external power adapter meets all
applicable standards for the country in which it is to be installed, and that it is
connected to a wall outlet which has earth ground.
WARNING

Configure the IP address 18
3088/I Getting Started Guide 2 • Initial Configuration
Connect a PC and log in
Using the included combination RS-232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port to
the NTU ’s Console port (red outline) (see figure 3).
Figure 3. Connecting G.SHDSL NTU to the PC’s serial port
1. Start a HyperTerminal session on the PC using the settings:
9600 bps, 8 data bits, no parity, 1 stop bit, no flow control
2. Log in to the G.SHDSL NTU using the factory-default login (superuser) and password (superuser):
Login: superuser
Password: *********
Login successful
Modify the IP address
1. Display current IP interface settings for the NTU Ethernet LAN port.
ip list interfaces <enter>
IP Interfaces:
ID | Name | IP Address | DHCP | Transport
—-|———|————————|—————|———————
1 | ip1 | 192.168.200.10 | disabled | <BRIDGE>
——————————————————————————
2. Modify the IP address for the LAN port according to your network requirements.
ip set interface ip1 ipaddress 10.10.4.10 255.255.255.0
Note The above IP address (10.10.4.10/24) is only an example. You must choose
an IP address on the same subnet as your PC.
3. Verify the new address is correct and save it in system boot memory.
fiip list interfaces <enter>
fisystem config save <enter>
The interconnecting cables shall be acceptable for external use
and shall be rated for the proper application with respect to volt-
age, current, anticipated temperature, flammability, and
mechanical serviceability.
CAUTION
MDI-X
Line
Ethernet
Power Console
Connect to Console port
Serial port
PC with
terminal emulator

Configure the IP address 19
3088/I Getting Started Guide 2 • Initial Configuration
Connect to the local IP network
Now you can connect the G.SHDSL NTU to your local IP network and complete the remaining configura-
tion from your PC using a standard web browser.
Connect the G.SHDSL NTU’s Ethernet port (green) to the same Ethernet segment as your PC (see figure 4).
The front-panel Ethernet Link LED should turn on. If it does not, press the rear-panel MDI-X switch so that
the Ethernet Link LED illuminates.
You can check the connection with the ping command. For example shown in figure 4, you would ping
10.10.4.10 from a PC on the IP network.
Figure 4. Connecting the G.SHDSL NTU to the local IP network (Model LB510A shown)
Log onto the web management interface
You will now access the web management graphical user interface (GUI) to configure the G.SHDSL NTU
using a standard web browser (such as Netscape Browser, Mozilla Firefox, or Internet Explorer).
1. At your PC, open a web browser and enter the IP address you assigned to the NTU’s Ethernet LAN port
in step 2 of section “Modify the IP address” on page 18. (In this example, 10.10.4.10.) (see figure 5)
Figure 5. G.SHDSL NTU web management home page
2. Log in to the web management home page using the username superuser and the password superuser.
MDI-X
Line
Ethernet
Power Console
Connect to Ethernet port Ethernet port
PC
MDI-X switch

Configure the IP address 20
3088/I Getting Started Guide 2 • Initial Configuration
Connect the G.SHDSL port
3. Obtain single-twisted-pair cable with an RJ-11 plug connector at each end.
4. Plug one end of the cable into the (yellow) RJ-11 socket (labelled Line) on the G.SHDSL NTU.
(See figure 6.)
5. Plug the other end of the cable into the RJ-11 wall socket that provides your G.SHDSL service.
6. Go to G.SHDSL > Configuration to configure the DSL port parameters.
Note If two G.SHDSL NTUs are connected back-to-back, one must be config-
ured as Remote, the other as Central.
7. The WAN Link LED will flash while in the process of establishing a link. The LED will be on constantly
once a valid DSL connection is established.
Figure 6. Rear view of LB510A showing DSL RJ-11 jack
MDI-X
Line
Ethernet
Power Console