Paxton Ins-30154 User manual
Page 1
e
l
b
a
e
g
ra
h
c
e
R
d
e
l
a
e
S
Battery
h
A
7
V
2
1
V21
V0
V21
V0
V42 V0
USP V0
10/05/2012
Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)
Saturday from 09:00 - 13:00 (GMT)
Technical Support
Paxton Net2
control unit
Back-up battery
Tamper Switch
Layout
12V DC Outputs
Ratings Label
Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/
Paxton
Ins-30154 24V AC/DC power supply with Net2 ACU
24V AC/DC input
24V DC Output
Input supply failure alarm
Page 2
1. Screws and wall plugs are provided in a tting kit.
With reference to the diagrams, determine where
the top, central mounting position is required and
drill a hole suitable for a No 8 wall plug.
2. Tap in one of the wall plugs.
3. Put in one of the long screws, leaving a suitable
gap to the wall surface and slide the cabinet over it.
4. Mark the hole positions for the lower 2 screws.
5. Remove the cabinet and drill the additional holes.
6. Tap in the 2 wall plugs and hang the cabinet back
onto the top screw.
7. Secure the cabinet with the 2 lower screws.
8. Tighten the top screw.
Fitting
Metal Cabinet
Plastic Cabinet
A Net2 nano ACU or a Hands free interface cannot be installed in
the Metal cabinet as this would block the RF signal used for the
Net2Air wireless technology.
This product is not suitable for retail sale.
All warranties are invalid if this product is
not installed by a competent person.
Input Connection
Anchor points are supplied inside the case to
secure the cable (cable ties are provided).
There are also 'knock-outs' in the case to allow
convenient access for the cable.
Use the supplied gland or grommet when passing
cable through any holes in the cabinet.
The battery backup function will not work until
this unit has rst been connected to the input
supply. It is the loss of this supply that switches
the unit to battery power.
The input cable must be passed around
the supplied Ferrite core.
This should be tted within 5 cm of the
connection with the power supply.
232 mm
68 mm
116 mm 25 mm
320 mm
268 mm
68 mm
136 mm
236 mm
196 mm
118 mm 18 mm
320 mm
284 mm
98 mm98 mm
Page 3
13.8V DC
24V DC
2 A
0.75 A
24 W
0.5 A
3.5 hours
24V AC or DC
2.3 A
50 Hz 60 Hz
0 °C +49 °C
0 °C +40 °C
232mm 320mm 80mm
236mm 320mm 80mm
150mm 100mm 62mm
:The following warnings and instructions MUST be adhered to. Read the instructions before installing and powering the
equipment. Keep the instructions in a safe place for future reference.
:RECEIVING INSPECTION- Remove any traces of packing material from the unit as such debris may create a re or shock hazard.
Unpack the unit with care and inspect for transit damage. If damage is suspected, the unit must not be used or tested, but should be
returned to Paxton for investigation and the damage reported to the carrier.
:INSTALLATION- Only qualied and trained personnel, familiar with this type of product and who fully understand these instructions
should install, connect or test this equipment. There are no user serviceable parts within the PSU unit.
:-The equipment is intended for indoor use only in dry locations.
:-This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required
to take adequate measures.
:-The installation must meet National Wiring Regulations and IEC60950-1 standards. A readily accessible disconnect device shall be
incorporated in the building wiring to include a 2.5A rated circuit breaker with at least a 3.0 mm contact gap.
Maximum 12V DC load output current
12V Output voltage
24V Output voltage
Maximum 24V DC load output current
Total power out (combined outputs)
Maximum battery charging current
Input supply voltage
Input supply current
Input supply frequency
Maximum battery life at full load (2A)
Registers an alarm if the input power fails when connected to an ACU or I/O board.
Input supply failure (PSU)
Status Lights
Specications
PSU Electrical
Features
The declaration of conformity is available on request. Contact details are provided at:
http://paxton.info/596
Green
Red
Battery backup
Fast/Trickle charge
Deep discharge protection
Tamper alarm
This LED is on when the input supply has failed - Power is being supplied by the battery.
This LED is on when the input supply is healthy.
The cabinet can accommodate a 12V / 7Ah battery.
The battery is continuously charged to keep it at maximum capacity.
If battery voltage falls below 9.5V, it will automatically disconnect - Red LED goes out.
Registers an alarm if the lid is opened when connected to an ACU or I/O board.
Environment
Metal Cabinet
Plastic Cabinet
Battery Compartment (Plastic Housing)
Dimensions
WARNINGS
Min Max
Width Height Depth
Waterproof No
ACU Electrical
Min Max
See accompanying documentation ( ins-30000 - Net2 classic, ins-30075 - Net2 nano, ins-30080 - Net2 plus )
Operating temperature - no battery backup
Operating temperature - with battery
Table of contents
Other Paxton Power Supply manuals
