PC POP Y20 Pefrect II Assembly instructions

Manual

Installation and system optimization guide:
The following manual and guides were carefully prepared by the PC POP Inc.
engineering team to help you maximize the potential of your PCPOP product.
Please keep this manual for future reference when upgrading or performing
maintenance.
2
CONTENTS
1................................................................................................
2...........................................................................................
3.......................................................................................
4....................................................................................
5................................................................
6........................................................................
7.........................................................................
8...................................................................
9........................................................................................
10............................................................
11.......................................................................
12.......................................................................
13.......................................................................
Cover
Contents
Specication
Names of parts
PSU, MotherBoard installation
Add on card installation
5.25” Device installation
3.5” / 2.5” Device installation
Switch, LED
Audio, USB, Auto Fan Controller
Completing installation
Remove the upper fan
Warranty information

3
SPECIFICATIONS

4
Names of parts

5
Installation Guide
1 .How to remove the side panel. 2. How to install the PSU.
3. How to install the motherboard.
Remove four thumb screws from the rear to
pull the side panels away from the case. Warning: PSU bottom fan can be setup facing up/down to accommodate any PSU type.

6
4. How to install the add-on cards.
Remove the expansion slot covers as required then insert expansion card into the case.
Secure with screws used to secure the expansion slots.

7
5. How to install the 5.25” devices.
1. Please remove front bezel to install ODD.
2. Insert the ODD device
3. Reinstall the front bezel.

8
6. How to install the 3.5” and 2.5” devices.
- Insert HDD into the hard drive tray
and then use screw A to secure it. - Insert SSD into the hard drive tray and then use screw B to secure it.
3.5” HDD 2.5” SSD

9
- Please refer to the illustration in the section of USB 2.0 and Audio connector
from the motherboard user manual. Please select the motherboard which uses the
same USB2.0, HD Audio standard as below. Otherwise, it will cause damage to devices.
- The following illustration is a diagram showing the front panel I/O connectors.
Power switch and reset switch installation guide:
LED connector installation guide：
Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector”
or “System Panel Connector” pin definition.
Power switch and reset switch have no polarity, so they can be connected in any orientation.
Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector”
or “System Panel Connector” pin definition.
The Power LED wires are separate pins for compatibility with different motherboard
pin definition so please make sure they are connected in the right polarity by referring
to your motherboard manual.
7. I/O Function panel installation guide.
Power Reset
Power LED HDD LED

10
USB & AUDIO：
Below are the front I/O connectors pin definition, please also check your motherboard
manual to cross reference with motherboard’s front I/O pin headers.
PCPOP’s I/O connectors are in block type to simplify installation.
HD Audio
USB 2.0 USB 2.0
USB 3.0
Caution : Connecting both USB 2.0 and USB 3.0 will cause shortage.
Must use only one connector

11
8. Completing installation.
After all wires and cables are connected and routed, place the side panels back on to the case
and secure with thumb screws removed from step 1.

12
PC POP Inc. guarantees that this device is free of defect in material and workmanship,
and provide a one-year limited hardware warranty for device commencing from the
date of purchase. Please keep your receipt for proof of purchase.
This product is designed for computer usage only. Using the device in any other capacity
voids the warranty. If you are not familiar with computer hardware installation, please
ask for professional assistance.
The warranty offered covers normal use. Defect or damage that result from improper
operation, storage, misuse or abuse, accident or neglect, which are not the fault
of PC POP Inc. are exclude from warranty coverage.
Customers assume all shipping cost to the PC POP RMA department for replacement
and PC POP will assume the cost in shipping back the replacement to the customer.
All replacement/repaired products are shipped via UPS, FedEx ground, or USPS service
unless a rush is requested, and all upgraded shipping is to be paid by the customer prior
to shipment.
If you have any questions or problems with PC POP product you purchased, please don't
hesitate to contact us at ([email protected])
Warranty information