PCE Health and Fitness LD213 Series User manual

Dual Channel Loop Detector
Model
–
LD213 Series
The LD213 is a dual channel inductive loop
card detector designed for parking and access
control applications.
The detector is connected to an inductive loop
mounted in the road surface. When vehicles
pass over the loop the detector switches on an
output.
The use of microprocessor and surface mount
technology enables a large number of functions
to be incorporated into a small package. The
LD213 is easy to set-up and install.
Typical applications in the parking and access control environments are safety loops for barriers or gates, arming
loops for activating card dispensers, vehicle counting with direction logic.
Features
App
lications
Reset Switch. Pressing the reset switch enables the detector to be manually reset during commissioning and
testing. This results in the detector re-tuning the sensing loop and becoming ready for vehicle detection.
Switch selectable Sensitivity. The detect sensitivity is the minimum change in inductance required to produce a
detect output. (%ΔL/L). Eight sensitivity settings are available on the switches to allow flexibility in configuration.
Switch selectable Frequency. The frequency of the loop is determined by the inductance of the loop and the
frequency switch setting. If the frequency switch is on, the frequency is reduced. It may be necessary to change
the frequency to prevent cross-talk between adjacent loops on different detectors.
Extend Option. When switched on this feature extends the presence output relay for 2 Seconds after the vehicle
has left the loop.
Direction Logic. This feature enables the detector to give a pulse output on relay1 for a vehicle travelling from
loop1 to loop2 and a pulse output on relay2 for a vehicle travelling from loop2 to loop1. To enable this feature
switches 2 and 4 must be on, and switches 3 and 5 must be off.
Pulse Relay Selection. The detect relay may be configured for a pulse output, and to energise on detection of a
vehicle or when the vehicle leaves the loop.
1

Selectable Pulse Time. This feature sets the length of time that the pulse relay will be energised. 1 Second or
0.2 Second.
Indicators
Power Indicator. This LED Indicator illuminates when power is present.
Detect Indicator. This LED Indicator is illuminated when there is a vehicle over the loop or the loop is faulty. This
LED can also be used to determine the loop frequency. On reset, count the number of times the LED flashes.
Multiply this number by 10KHz.For example: if the LED flashes 6 times, then the loop frequency is between
60KHz and 70KHz.
Loop Fault Indicator. This LED Indicator is illuminated when the loop is either open circuit or short circuit and is
used to give a visual indication of a faulty loop.
Technical S
p
ecifications
Power supply 11 - 26VAC/DC 50/60Hz 100mA max.
Presence Relay Mode 0.5A/220VAC (Fail Safe – normally energized)
Pulse Relay Mode 0.5A/220VAC(Non Fail Safe–normally denergised)
Response time Approximately 120ms after vehicle enters loop.
Indicators LED indicators show: Power, Detect state and Loop Fault.
Detector tuning range 15 - 1500uH
Loop Frequency Approx. 23 – 130KHz (Multiplexing)
Environmental tracking Automatic Compensation
Protection Loop isolation transformer with zener diodes and gas discharge tube.
Connecto
r
LD213-1 14Way MOLEX Pug Connector
LD213-2 14Way Screw terminal block
LD213-3 14Way Pin Strip Connector
Dimensions 105mm X 68mm
Operating Temperature -40°C to +80°C
Storage Temperature -40°C to +85°C
2

LD213 Switch Settings
Switch No. Function
ON OFF
10 Presence Relay Extend Time 2 Sec Off
7,8,9 Sensitivity 0.02% - S7/S8/S9
7,8,9 Sensitivity 0.01% S9 S7/S8
7,8,9 Sensitivity 0.05% S8 S7/S9
7,8,9 Sensitivity 0.1% S8/S9 S7
7,8,9 Sensitivity 0.2% S7 S8/S9
7,8,9 Sensitivity 0.5% S7/S9 S8
7,8,9 Sensitivity 1% S7/S8 S9
7,8,9 Sensitivity 2% S7/S8/S9 -
6 Frequency Low High
5 Mode Loop 1 Relay Pulse Presence
4 Mode Loop 1 Relay (Pulse Mode) Undetect Detect
3 Mode Loop 2 Relay Pulse Presence
2 Mode Loop 2 Relay (Pulse Mode) Undetect Detect
1 Loop 1 and Loop 2 Relay Pulse Time 1 Sec 0.2 Sec
To select direction logic mode, S2/S4 must be ON and S3/S5 must be OFF.
Rela
y
Functionalit
y
Switch Settin
g
s
RELAYS
(Presence or Pulse) VEHICLE PRESENT NO VEHICLE LOOP FAULTY
NO
POWER
PRESENCE
RELAY
N/O CLOSED OPEN CLOSED CLOSED
N/C OPEN CLOSED OPEN OPEN
PULSE
RELAY
N/O PULSE CLOSED OPEN CLOSED CLOSED
N/C PULSE OPEN CLOSED OPEN OPEN
3

4
SYMPTOM POSSIBLE CAUSE SOLUTION
The POWER LED is not
on.
No power supply voltage on
the input.
Check that the power supply is
correctly wired to the detector.
(PINS 1 and 2)
The DETECT LED flashes
erratically.
There may be a poor
connection in the loop or
loop feeder.
The detector may be
experiencing crosstalk with
the loop of an adjacent
detector.
Check all wiring. Tighten screw
terminals. Check for broken wires.
Try changing frequencies using the
frequency switch. Put the detector
with the larger loop onto low
frequency and the detector with the
smaller loop onto high frequency.
The DETECT LED
randomly stays on.
Faulty loop or loop feeder
wiring.
Movement of the loop in the
ground.
Check the wiring. Tighten screw
terminals. Check for pinched or bent
wires. Is the feeder wire twisted?
Check for cracks in the road surface
near the loop.
The LOOP FAULT LED is
flashing.
The loop inductance is too
small or the loop is short
circuit.
Check that there is no short circuit
on the loop feeder wiring or the loop.
If there is no short circuit then the
inductance is to small and more
turns of wire should be added to the
loop.
The LOOP FAULT LED is
permanently illuminated.
The loop inductance is too
large or the loop is open
circuit.
Check that there is electrical
continuity on the loop. This can be
done using a multimeter on the
ohms range (< 5 Ω). If the loop
inductance is too large then try
reducing the number of turns.
Wirin
g
Dia
g
ram
Dia
g
nostics
11
LOOP1 INPUT
12
9
POWER INPUT
10
8
12-24VAC/DC
0V
RESET
LOOP1 TWISTED
5
4
3
13
LOOP2 INPUT
14
LOOP2 TWISTED
PRESENCE/PULSE
RELAY OUTPUT 1
2
7
6
PRESENCE/PULSE
RELAY OUTPUT 2

5
NOTE: To ensure correct operation of the LD213, the circuit board must be securely mounted using the 4
mounting holes located near the corners of the board. It is also important that nothing touches the underside of
the circuit board.
Mechanical La
y
out
Wirin
g
Connections
14 LOOP2 TWISTED
13 LOOP2 WIRE
12 LOOP1 TWISTED
11 LOOP1 WIRE
10 OV
9 + 12 TO 24VAC/DC SUPPLY
8 RESET
7 RLY CH2 N.C.
6 RLY CH2 COM
5 RLY CH1 N.O.
4 RLY CH1 N.C.
3 RLY CH1 COM
2 RLY CH2 N.O.
1 CHASSIS
DETECT
LED’s
LD213
59 mm
96 mm
MODE SWITCH
1 2 3 4 5 6 7 8 9 10
LOOP
FAULT
LED’
s
RESET
SWITCH
1
TERMINALS
14 CH2
POWER
CH1

Loo
p
Installation Guide
1. The detector should be installed in a waterproof housing as close to the loop as possible.
2. The loop and feeder should be made from insulated copper wire with a minimum cross-sectional area of
1.5mm2. The feeder should be twisted with at least 20 turns per metre. Joints in the wire are not
recommended and must be soldered and made waterproof. Faulty joints could lead to incorrect operation of
the detector. Feeders which may pick up electrical noise should use screened cable, with the screen earthed
at the detector.
3. The loop should be either square or rectangular in shape with a minimum distance of 1 metre between
opposite sides. Normally 3 turns of wire are used in the loop. Large loops with a circumference of greater than
10 metres should use 2 turns while small loops with a circumference of less than 6 metres should use 4 turns.
When two loops are used in close proximity to each other it is recommended that 3 turns are used in one and
4 turns in the other to prevent cross-talk.
4. Cross-talk is a term used to describe the interference between two adjacent loops. To avoid incorrect
operation of the detector, the loops should be at least 2 metres apart and on different frequency settings.
5. For loop installation, slots should be cut in the road using a masonry cutting tool. A 45o cut should be made
across the corners to prevent damage to the wire on the corners. The slot should be about 4mm wide and
30mm to 50mm deep. Remember to extend the slot from one of the corners to the road-side to accommodate
the feeder.
6. Best results are obtained when a single length of wire is used with no joints. This may be achieved by running
the wire from the detector to the loop, around the loop for 3 turns and then back to the detector. The feeder
portion of the wire is then twisted. Remember that twisting the feeder will shorten its length, so ensure a long
enough feeder wire is used.
7. After the loop and feeder wires have been placed in the slot, the slot is filled with epoxy compound or bitumen
filler.
6
300mm 300mm
1M
ROAD
EDGE
45
O
CROSSCUT
FEEDER
TRAFFIC DIRECTION
4mm
ROAD SURFACE
SLOT
SEALANT
30-50 mm
WIRES
Contact Details
Refer to our web site for distributor details.
Email: [email protected]
Web: www.proconel.com