PCS Pulseworx PIM-U User manual

Model: PIM-U
Powerline Interface Module
Installation Guide and
Owner’s Manual
The Inventors Of: 19215 Parthenia St. Suite D
Northridge, CA 91324
P: 818-701-9831 [e-mail]
https://pcswebstore.com www.pcslighting.com
FUNCTION
The PIM-U Powerline Interface Module - USB is the de facto
interface between a computer and the Universal Powerline
Bus (UPB). The PIM-U connects to the USB port of your
computer with a standard serial cable (provided) and sends
and receives UPB communication packets on the existing
house wiring. The PIM-U can be plugged into any free wall
outlet throughout the home. The device also provides a pass-
thru outlet for other electronic devices. No additional wiring is
required and no radio frequency signals are used for
communication.
DRIVER INSTALLATION
The very first time that the PIM-U is used with a computer it is
very likely that you will need to install software driver as soon
as the device is plugged into the computer
1. Windows 7 or Windows 10 will automatically search
for the correct driver via. Windows Update search. It
may take up to 5 to 10 minutes for the installation
process. Please be patient. A dialog will prompt.
2. If Windows fail to search for driver update, please use
the following link to download the driver,
http://www.ftdichip.com/Drivers/VCP.htm
NOTE: For Windows XP users, the driver’s link also
applies.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic safety precautions
should always be followed, including the following:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. Keep away from water. If the product comes in contact
with water or other liquid, turn off the circuit breaker and
unplug the product immediately.
3. Never use products that have been dropped or damaged.
4. Do not use this product outdoors.
5. Do not use this product for other than its intended purpose.
6. To avoid any risk of fire, burns, personal injury or electric
shock, install this product out of the reach of small children.
7. Do not cover this product with any material when in use.
8. This product uses grounded plugs and sockets to reduce the
risk of electric shock. These plugs and sockets fit only one
way. If they do not fit, consult an electrician.
9. SAVE THESE INSTRUCTIONS.
INSTALLATION
The Powerline Interface Module is designed for indoor use with
devices that provide a USB serial port. To install the PIM-U
module follow these steps:
1. Connect the serial cable (provided) between the PIM’s USB
serial connector and any open USB port of the computer.
2. Plug the PIM-U into any grounded wall outlet.The Status
LED should start blinking and then stay solid blue.
OPERATION
The PIM-U is the perfect interface device for use with PCS’
UPStart Setup Software. UPStart allows you to easily configure all
of your PulseWorx Lighting System devices. The UPStart User’s
Guide (available at
http://www.pcslighting.com/pulseworx/resources) explains how
to configure your system using UPStart software.
To use the PIM-U with UPStart select Network
ribbonPowerline Interface DeviceConfigure to bring up the
UPB Interface Setup dialog.

Model: PIM-U
Powerline Interface Module
Installation Guide and
Owner’s Manual
The Inventors Of: 19215 Parthenia St. Suite D
Northridge, CA 91324
P: 818-701-9831 [e-mail]
https://pcswebstore.com www.pcslighting.com
Select the correct Interface Type and then press the “Find UPB
Interface port” button. UPStart will automatically find the
Communication Port that the PIM-U is connected to. Next,
press the “Connect” button to have UPStart connect and test
the PIM-U
Signal & Noise Meters
Once connected, the PIM-U will constantly send reports to
UPStart as to what is currently happening on the powerline.
You can get a peek into the results of these reports by pressing
the Signal & Noise Meters button to bring up the UPB
Interface Diagnostics shown below.
The meters will display a real-time indication of what the PIM-
U is reporting. UPStart will also classify the reports as either
“Signal” or “Noise” and display them on the proper meter.
The meters are very useful for troubleshooting problems on
the powerline.
Status LED Indications
The PIM-U contains a bi-color (blue/red) Status LED that will
also give a visual indication of what UPB information is
currently on the powerline.
Blue:
No UPB Signal
Magenta:
Received a UPB Message
Red:
Transmitted a UPB Message
Push-button
The push-button on the front of the PIM-U is used to put the
device back to its factory default condition. To set the PIM-U
back to factory defaults first press the pushbutton 5times
rapidly. The Status LED will blink blue. Next, press the
pushbutton 10 times. The Status LED will blink red. Finally, press
the pushbutton 2times. The Status LED will stop blinking. The
device is now restored to its factory default state.
CONFIGURATION
The PIM-U has an adjustment for UPB receive sensitivity. The
factory default for this setting is “High”. If the PIM-U is to be used
in severe powerline noise, you may find that it operates better in
the “Low” receive sensitivity setting.
To adjust the receive sensitivity press the “Settings” button on the
UPB Interface Setup dialog. Next, select the desired receive
sensitivity setting and press the “OK” button.
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all
applicable instructions, to be free from original defects in
materials and workmanship for a period of five years from the
date of purchase. Refer to the warranty information on the
PulseWorx website (www.PulseWorx.com) for exact details.