Peavey SA 4200 User manual

SA-4200 SPECIFICATIONS
SPECIFICATION LOW Z MODE 70 VOLT MODE
Rated Power (all channels driven)
Dual-Dual Mono & Parallel Modes
4 Ohms 200 Watts −
8 Ohms 130 Watts −
70 Volts −200 Watts
Minimum Load Impedance 4 Ohms 25 Ohms
Bridged Mode (Ch A & B)
8 Ohms 400 Watts −
16 Ohms 260 Watts −
140 Volts −400 Watts
Minimum Load Impedance 8 Ohms 50 Ohms
Frequency Response
+0, -1dB @ 1Watt <10Hz −35kHz 80Hz −30kHz
+0, -3dB @ full power 18Hz −30kHz 60Hz −15kHz
with 60Hz Low-Cut engaged
THD
at rated power, 1kHz <0.05% <0.05%
IMD (SMPTE) <0.10% <0.10%
Damping Factor >140 (8 Ohms) >400
Input CMRR -60 dB typ -60 dB typ
Voltage Gain ×20 (26dB) typ ×50 (34dB) typ
Input Sensitivity 1.42V (4 Ohms) 1.42V
1.62V (8 Ohms)
Input Impedance 20K Ohms balanced 20K Ohms balanced
10K Ohms unbalanced 10K Ohms unbalanced
Noise and Hum below rated output
delay channels (C & D) bypassed;
22Hz–22kHz BW -95 dB -95 dB
C & D delay active
A-weighted -88 dB -88dB
Current Consumption Multiply currents by 0.5 for 230V units.
Rated power 15.5 A (4 Ohms) 13.7 A
10.2 A (8 Ohms)
1/
3rated power 9.8 A (4 Ohms) 8.7 A
6.4 A (8 Ohms)
⅛rated power 6.6 A (4 Ohms) 5.9 A
4.2 A (8 Ohms)
Idle 0.5 A 0.9 A
Thermal Emission
1/
3power 3110 BTU/hr (4 Ohms) 2655 BTU/hr
2035 BTU/hr (8 Ohms)
⅛power 2365 BTU/hr (4 Ohms) 2080 BTU/hr
1500 BTU/hr (8 Ohms)

Controls
Front: 4 channel input signal attenuators, AC switch
Rear: 2 output mode switches; Ch A & B bridge switch; HPF switches;
AUTODELAY™ bypass switches; AUTODELAY setup switches
Indicator LEDs
Front: 4 Clip, 4 Signal, 1 Power
Rear: AUTODELAY setup
Protection
Over-Temperature, DC, turn on/off transients, subsonic, incorrect load, short-circuit
Connectors
Input: Four female XLRs - LINE INPUTS
One female XLR - TEST MICROPHONE
Output: Two 4-position barrier strips - SPEAKER OUTPUTS
One male XLR - REFERENCE OUTPUT
Construction
16 gauge steel reinforced with 12 gauge rack ears
Dimensions
Height: 3.50” (8.84 cm) 2 EIA rack spaces
Width, front: 19.00” (48.26 cm)
Width, rear: 17.00” (43.18 cm)
Overall depth: 17.05” (43.31 cm)
Mounting depth: 16.63” (42.24 cm) behind front rack ears
Weight
40 lbs (18.1 kg)
Power Requirements
100, 120, 230-240 Vac, 50-60 Hz
1200 Watts
Test Conditions
120Vac, 60Hz line input voltage maintained
All channels operating unless otherwise noted
Due to our efforts for constant improvements, features and
specifications listed herein are subject to change without notice.