Peavey SSE 10 User manual

Description
The SSE is a new enclosure series
featuring high power ratings with custom
components, a sleek look and a unique,
snap-in metal grille. The SSE 10 is a two-
way system featuring the highly acclaimed
Pea ey 14XT titanium compression dri er
with the di erse Sound Guard IV tweeter
protection network and a maximum-
performance 10" woofer for a smooth
response. The SSE 10 is rated at 400 Watts
program and 800 Watts peak. This
lightweight speaker system is ideal for
smaller enues where space is at a
premium. Connections are made using a
four-pin Neutrik®Speakon®or paralleled
two-position terminal block for additional
cabinets. The SSE 10 incorporates flying
points on the top of the unit and mounting
points on the bottom for utilizing the
Pea ey VersaMount70 mounting bracket.
The SSE series is a ailable in black, white
and natural finishes.
Features:
• Two-way sound reinforcement
enclosure
• Designed for permanent install
• A ailable in three finishes: black,
white or natural
• Premium 10" woofer
• Pea ey 14XT™titanium
compression dri er
• Sound Guard™IV tweeter
protection network
• Se en flying points (six 3/8" for
suspension and one 1/4" for angle
adjustment)
• Mounting point for VersaMount™
70 bracket
• 13 mm Birch plywood
construction
• 400 Watts program/800 Watts
peak power handling
• 80 Hz to 17 kHz
• 95 dB at 1W/1m
• 8 Ohms
Frequency response, 1 meter on-axis,
swept-sine in anechoic environment:
80 Hz to 17 kHz (±3 dB)
Usable low frequency limit (-10 B
point):
60 Hz
Power han ling:
Full range:
400 W program
800 W peak
Soun pressure level, 1 Watt, 1 meter in
anechoic environment:
Full range:
95 dB SPL 2.83 V input)
Maximum soun pressure level
(1 meter):
Full range:
118 dB SPL continuous
124 dB SPL peak
SPECIFICATIONS
SSE™10

2
Ra iation angle measure at 6 B
point of polar response:
500 Hz to 1.6 kHz:
Horiz. 125˚ ± 25˚
Vert. 130˚ ± 15˚
1.6 kHz to 5 kHz:
Horiz. 105˚ ± 20˚
Vert. 75˚ ± 30˚
5 kHz to 16 kHz:
Horiz. 95˚ ± 25˚
Vert. 65˚ ± 10˚
Directivity factor, Q (Mean):
7.19 ± 6.07
Directivity in ex, Di (Mean):
8.09 dB ± 2.01 dB
Trans ucer complement:
Low frequency section:
Premium-grade 10" woofer
High frequency section:
Pea ey 14XT™titanium diaphragm
compression dri er
on a 90° x 60° constant directi ity horn
Box tuning frequency:
Low frequency section:
78 Hz
Harmonic istortion:
1% rated power
Second harmonic:
100 Hz: 0.43%
1 kHz: 0.07%
Third harmonic:
100 Hz: 0.58%
1 kHz: 1.02%
10% rated power
Second harmonic:
100 Hz: 2.28%
1 kHz: 0.40%
Third harmonic:
100 Hz: 0.97%
1 kHz: 2.02%
Electro-acoustic crossover frequency
(internal passive):
2.1 kHz
Impedance (Z):
Full range:
Nominal: 8 Ω
Minimum: 6 Ω
Input Connection:
1 four-pin Neutrik®Speakon®in parallel
with 1 two-position terminal strip
Enclosure materials an finish:
Trapezoidal, dado-joined, 12 mm 9-ply
Birch finished with a textured acrylic
polyurethane, with a full-length metal
grille co ered with acoustical-grade grille
cloth. A ailable in black, white or natural
finishes.
Mounting provisions:
(6) 3/8"-16 threaded mounting
suspension points (three each top and
one each side and back). Use only
forged shoulder machinery eye bolt,
Mil Spec MIL51937-3.
(1) 1/4"-20 threaded mounting point
on back bottom for angle adjustments.
(4) 1/4"-20 threaded mounting
points on bottom to accommodate use
of VersaMount™70 adjustable
mounting bracket.
(4) 1/4"-20 threaded mounting points.
DO NOT suspen this unit upsi e
own using the VersaMount system.
Dimensions (H x W x D):
Front:
19.63" x 15.09" x 12.12"
498 mm x 383 mm x 308 mm
Rear:
19.63" x 11.09" x 12.12"
498 mm x 383 mm x 308 mm
Net Weight:
29 lbs. (13.2 kg)
Frequency response
This measurement is useful in determining
how accurately a gi en unit reproduces an
input signal. The frequency response of
the SSE 10 is measured at a distance of 1-
meter using a 1 Watt (into the nominal
impedance) swept-sine input signal. As
shown in figure 1, the selected dri ers in
the SSE 10 combine to gi e a smooth
frequency response from 80 Hz to 17 kHz.
Directivity
Beamwidth is deri ed from the -6 dB
points from the polar plots (see figure 3),
which are measured in a whole space
anechoic en ironment. Q and Directi ity
Index are plotted for the on-axis
measurement position. These
specifications pro ide a reference to the
co erage characteristics of the unit and
pro ide insight into proper placement and
installation in the chosen en ironment.
The blending of the components of the
SSE 10 exhibit a desirable beamwidth and
directi ity (figures 3 and 4) suitable for
sound reinforcement applications.
Power han ling
There are many different approaches to
power handling ratings. Pea ey rates this
loudspeaker system’s power handling
using a full-range form of the AES
Standard 2-1984. Using audio band 20 Hz
to 20 kHz pink noise with peaks of four
times the RMS le el, this strenuous test
signal assures the user that e ery portion
of this system can withstand today's high
technology music. This rating is contingent
upon ha ing a minimum of 3 dB of
amplifier headroom a ailable.
Harmonic istortion
Second and third harmonic distortions s.
frequency are plotted in figures 5 and 6 for
two power le els. Ten percent (10%) of
rated input power and either one percent
(1%) of rated input power or 1 Watt,
whiche er is greater. Distortion is read
from the graph as the difference between
the fundamental signal (frequency
response) and the desired harmonic. As an
example, a distortion cur e that is down
40 dB from the fundamental is equi alent
to 1% distortion.
Mounting
Caution: Before attempting to suspend or
mount this speaker, consult a certified
structural engineer. The speaker may fall
due to improper installation, resulting in
serious injury and property damage. DO
NOT suspend or mount any other product
or de ice from this enclosure. The
maximum enclosure angle is 45°. Use only
Grade 5 hardware or better. All associated
rigging is the responsibility of others.
Architectural an Engineering
Specifications
The loudspeaker system shall ha e an
operating bandwidth of 80 Hz to 17 kHz.
The nominal output le el shall be 95 dB
when measured at a distance of a meter
with an input of 1 Watt. The nominal
impedance shall be 8 Ohms. The
maximum program power handling shall
be 400 Watts with a peak power input of at
least 800 Watts and a minimum amplifier
headroom of 3 dB. The nominal radiation
geometry shall be 90˚ in the horizontal
plane and 60˚ in the ertical plane. The
outside dimensions shall be 19.63" high
by 15.09" wide by 12.12" deep. The weight
shall be 29 lbs. The loudspeaker system
shall be a model SSE 10.
3 + 2 YEAR LIMITED WARRANTY
NNOOTTEE:: For details, refer to the warranty
statement. Copies of this statement may
be obtained by contacting Pea ey
Electronics Corporation, P.O. Box 2898,
Meridian, Mississippi 39301-2898.

SPECIFICATIONS
SSE™10
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
60
70
80
90
100
110
dB SPL (re 20 Pa)
Amplitude Response (1W 1m On-Axis)
Figure 1
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
1
10
100
Q & Directivity Index
Q
Figure 4
20
10
Di
0
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
30
40
60
80
100
140
180
300
360
Beamwidth (Degrees)
Beamwidth
Vertical
Horizontal
Figure 3
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
1
2
3
5
10
20
30
50
100
Impedance
Z
()
Figure 2
3

4
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
40
50
60
70
80
90
100
110
dB SPL (re 20 Pa)
Harmonic Distortion : 1% Rated Power
Figure 6 3rd Harmonic
2nd Harmonic
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
50
60
70
80
90
100
110
120
dB SPL (re 20 Pa)
Harmonic Distortion : 10% Rated Power
Figure 5 3rd Harmonic
2nd Harmonic

SPECIFICATIONS
SSE™10
0o
30o
60o
90o
-30o
-60o
-90o
50 Hz
0o
30o
60o
90o
-30o
-60o
-90o
125 Hz
0o
30o
60o
90o
-30o
-60o
-90o
200 Hz
0o
30o
60o
90o
-30o
-60o
-90o
315 Hz
0o
30o
60o
90o
-30o
-60o
-90o
250 Hz
0o
30o
60o
90o
-30o
-60o
-90o
400 Hz
0o
30o
60o
90o
-30o
-60o
-90o
630 Hz
0o
30o
60o
90o
-30o
-60o
-90o
500 Hz
0o
30o
60o
90o
-30o
-60o
-90o
63 Hz
0o
30o
60o
90o
-30o
-60o
-90o
100 Hz
0o
30o
60o
90o
-30o
-60o
-90o
160 Hz
Vertical Polar Patterns 6 dB per Division
0o
30o
60o
90o
-30o
-60o
-90o
80 Hz
5

6
0o
30o
60o
90o
-30o
-60o
-90o
800 Hz
0o
30o
60o
90o
-30o
-60o
-90o
1.25 kHz
0o
30o
60o
90o
-30o
-60o
-90o
2 kHz
0o
30o
60o
90o
-30o
-60o
-90o
3.15 kHz
0o
30o
60o
90o
-30o
-60o
-90o
5 kHz
0o
30o
60o
90o
-30o
-60o
-90o
4 kHz
0o
30o
60o
90o
-30o
-60o
-90o
6.3 kHz
0o
30o
60o
90o
-30o
-60o
-90o
10 kHz
0o
30o
60o
90o
-30o
-60o
-90o
8 kHz
0o
30o
60o
90o
-30o
-60o
-90o
1 kHz
0o
30o
60o
90o
-30o
-60o
-90o
1.6 kHz
0o
30o
60o
90o
-30o
-60o
-90o
2.5 kHz
Vertical Polar Patterns 6 dB per Division

SPECIFICATIONS
SSE™10
0o
30o
60o
90o
-30o
-60o
-90o
12.5 kHz
0o
30o
60o
90o
-30o
-60o
-90o
16 kHz
Vertical Polar Patterns 6 dB per Division
7

8
-90o
-60o
-30o
0o
30o
60o
90o
50 Hz
-90o
-60o
-30o
0o
30o
60o
90o
80 Hz
-90o
-60o
-30o
0o
30o
60o
90o
125 Hz
-90o
-60o
-30o
0o
30o
60o
90o
200 Hz
-90o
-60o
-30o
0o
30o
60o
90o
315 Hz
-90o
-60o
-30o
0o
30o
60o
90o
250 Hz
-90o
-60o
-30o
0o
30o
60o
90o
400 Hz
-90o
-60o
-30o
0o
30o
60o
90o
630 Hz
-90o
-60o
-30o
0o
30o
60o
90o
500 Hz
-90o
-60o
-30o
0o
30o
60o
90o
63 Hz
-90o
-60o
-30o
0o
30o
60o
90o
100 Hz
-90o
-60o
-30o
0o
30o
60o
90o
160 Hz
Horizontal Polar Patterns 6 dB per Division

SPECIFICATIONS
SSE™10
-90o
-60o
-30o
0o
30o
60o
90o
800 Hz
-90o
-60o
-30o
0o
30o
60o
90o
1.25 kHz
-90o
-60o
-30o
0o
30o
60o
90o
2 kHz
-90o
-60o
-30o
0o
30o
60o
90o
3.15 kHz
-90o
-60o
-30o
0o
30o
60o
90o
5 kHz
-90o
-60o
-30o
0o
30o
60o
90o
4 kHz
-90o
-60o
-30o
0o
30o
60o
90o
6.3 kHz
-90o
-60o
-30o
0o
30o
60o
90o
10 kHz
-90o
-60o
-30o
0o
30o
60o
90o
8 kHz
-90o
-60o
-30o
0o
30o
60o
90o
1 kHz
-90o
-60o
-30o
0o
30o
60o
90o
1.6 kHz
-90o
-60o
-30o
0o
30o
60o
90o
2.5 kHz
Horizontal Polar Patterns 6 dB per Division
9

10
-90o
-60o
-30o
0o
30o
60o
90o
12.5 kHz
-90o
-60o
-30o
0o
30o
60o
90o
16 kHz
Horizontal Polar Patterns 6 dB per Division

SPECIFICATIONS
SSE™10
Input Plate
11

www.sanctuary-series.com
80305310
Features and specifications subject to change without notice.
Pea ey Electronics Corporation 711 A Street Meridian, MS 39301 [phone] FAX [phone] ©2004 Printed in the U.S.A. 3/04