Pedigree Technologies CameraView JC400 User manual

INSTALLATION MANUAL
PedigreeTechnologies.com | Support: (701)-499-0022
CameraView (Mitac Camera)
Document ID: IM-DC-X4
Last Updated: April 21, 2022
Pedigree Technologies recommends using a professional installer for optimal
results. Please let your Pedigree Technologies representative suggest a provider if
you need help with your hardware installations.

2
Prerequisites
PedigreeTechnologies.com | Support: (701)-499-0022
CameraView
Mitac
Required Information
• Name of asset (ex: Propane Truck #20)
• IMEI of each device to be installed (IMEI is on the label where the mounting plate is attached)
Standard Equipment
Required Tools
Rubbing Alcohol or Window Cleaner (to clean window surface for best adhesion)
Level (to level camera during mounting)
Drill with Phillps & Torx bits
Small Socket Set
Volt Meter
Tablet with POV (Optional: to see live view of camera when setting mounting location)
Camera
Before You Begin
TIPS FOR PROPER CAMERA MOUNTING
• Ideal Location: Center (or as close to center as possible) of the windshield.
• Ideal Height: Highest point near rearview mirror - in the area swept by the wipers.
• Field of View: Should be clear of any occlusions (EZPass, rear view mirror, window tint, etc.)
• Angle: Camera should have a negative pitch angle (it should look “down” a few degrees.)
• The eld of view should not have too much “sky”.
• Split windows may have to adjust mounting location other than what is recommended in this
document. Consult with your implementation manager at Pedigree Technologies.
Power/Accessory
Harness
Tamper Cover
Mounting Plate
Optional Inline Fuses Optional Circuit Taps

PedigreeTechnologies.com | Support: (701)-499-0022
3
CameraView
JC400
Installation Steps, Continued
Determine proper placement of camera on the
front windshield. (Dry t only. It’s important to run
cabling to power source and determine where it will
t properly.)
• High on the windshield next to the rearview mirror
area right of center divider
• Highest possible placement within the wiper
blade path
• Avoid any overhanging exterior sun visor or other
materials on glass including rock chips or cracks.
Dry Fit
Installation Steps, Continued
Power Cable
During the dry t, make sure you can route the cable inside the headliner and A pillar to the ELD
cradle (or fuse panel for direct wire installations). (Avoid airbags and other hardware inside the
A pillar.) Cables and wiring should be routed behind the dash and should not be visible after
installation is complete. (Connect the accessory harness to cradle or power/fuse panel before
actually routing the cables in the A pillar.)

PedigreeTechnologies.com | Support: (701)-499-0022
4
CameraView
Mitac
APMM Power Module Installation for Cab-Mate One
STEP ONE
Identify and record the ESN of the Cab-Mate One
before proceeding. The following steps will cover the
serial number and you will need it for activating the
device later, or servicing the device in the future.
STEP TWO
For new intalls of the Cab-Mate One, install
the diagnostic data cable as per the Cab-Mate
One installation document. DO NOT CONNECT
DIAGNOSTIC CABLE TO CRADLE YET
STEP THREE (for new Cab-Mate One installs)
Remove the ball mount from the Panavise mount.
With the other side (the long piece) locate the
desired position on the dash of vehicle and secure
with hardware.
Secure to Dash
Secure to tablet in
step ve
Panavise Mount
STEP THREE - 2 (for previously installed Cab-Mate One)
Remove the ball mount from the Panavise mount and remove from the back of the tablet by
removing the 4 fastening screws.
STEP FOUR
Dry t CameraView module as per the installation instructions (page 3 of this document), routing
the USB cable to the Cab-Mate One, but do not plug it into the APMM module yet.
Installation of new Cab-Mate One plus camera - Start with Step One
Installation of camera on previously installed Cab-Mate One - Start with Step Three - 2
Installation of new camera on Cab-Mate One with previously installed camera (switching out
cameras) - Start with Step Eleven

PedigreeTechnologies.com | Support: (701)-499-0022
5
APMM Power Module Installation for Cab-Mate One continued
STEP FIVE
Secure the APMM bracket to the Cab-Mate One by sandwiching it between the Cab-Mate One
and the ball mount using the supplied screw and washer pack. (Use the longer machine screws
provided, paired with star washers.)
+ +
STEP SIX
Secure the APMM module to bracket using the supplied double-sided tape with the text side
facing up as pictured below.
+ =
Ball Mount APMM Bracket Cab-Mate One
STEP SEVEN
Connect the 16pin and 6 pin plugs of the APMM harness to the ports on the bottom of the Cab-
Mate One. (For previously installed Cab-Mate One, remove 16 pin connector from bottom of Cab-
Mate One and replace with the APMM harness.)
APMM Harness
Bottom view
CameraView
Mitac

PedigreeTechnologies.com | Support: (701)-499-0022
6
APMM Power Module Installation for Cab-Mate One continued
STEP EIGHT
Connect the APMM harness to the AUX1 and LMU DIAG ports on the top of the APMM module.
STEP NINE
Mount the Cab-Mate One/APMM
assembly to the dash using the Panavise
ball mount (not pictured).
STEP TEN
Connect the diagnostic cable to the port
on the APMM labled “VEHICLE DIAG” on
the bottom of the APMM module.
STEP ELEVEN
For a previosly installed camera, unplug the
10 pin plug from the port on the side of the
APMM power module.
Top view
Bottom view
STEP TWELVE
Connect the 10 pin plug from the
Power/Accessory Harnes cable into
the port on the side of the APMM
power module.
CameraView
Mitac
Unplug previous
cable
Connect 10 pin plug
from power cable

PedigreeTechnologies.com | Support: (701)-499-0022
7
APMM Power Module Installation for CalAmp LMU 3640
STEP ONE
For a previously installed LMU 3640, unplug the
diagnostic cable from the LMU.
STEP TWO
Plug the longer 16-pin plug from the APMM
harness into the 16 pin port on the LMU, replacing
the diagnostic cable you just removed if working on
previously installed LMU.
STEP THREE
Plug the male 5 pin plug from the APMM harness
into the female 5 pin plug of the accessory harness.
OPTIONAL STEP
If this is a new installation of the LMU 3640, plug
the 20 pin plug of the accessory harness into the
20 pin port of LMU.
Remove Existing
Diagnostic Cable
APMM Harness
Male 5 pin from
APMM Harness
Female 5 pin
from Accessory
Harness
CameraView
Mitac

PedigreeTechnologies.com | Support: (701)-499-0022
8
STEP FOUR
Plug the 16 pin plug from the short end of the
APMM harness into the LMU DIAG port on the
power module.
STEP FIVE
Plug the 6 pin plug from the APMM harness into
the AUX 1 port on the power module.
STEP SIX
Plug the diagnostic cable (from STEP ONE) into the
VEHICLE DIAG. port on the power module.
STEP SEVEN
Plug the usb adapter cable into the 10 pin port on
the side of the power module.
APMM Power Module Installation - CalAmp LMU 3640 continued...
APMM Harness
Power Module
Diagnostic Cable
Power Module
Camera Power
Cable
For a previously installed camera, remove the power
cable of the old camera and replace with the 10 pin
connector of the new camera power/accessory
harness.
CameraView
Mitac

PedigreeTechnologies.com | Support: (701)-499-0022
9
Direct Wire Installation Option
CameraView
Mitac
STEP ONE
Cut off the 10-pin molex connector from the power
cable.
STEP THREE
The Yellow wire (power) should be
connected to a constant 12-24VDC power source
found at the key source or the fuse panel.
(Circuit taps are provided in the hardware kit if
needed, however soldering and using inline fuses is
the recommended connection.)
STEP TWO
The Black wire (ground) should be securely fastened
to a grounded screw or chassis ground.
STEP FOUR
The Red wire (ignition) is the ignition event wire that
is best installed direcly to 12v switched ignition
wire.
Ensure that power to the ignition wire is availabe
ONLY when the vehicle ignition is turned on. All
makes and models of vehicles are different - we
recommend knowledge of the particular vehicle’s
constant and ignition wiring prior to installation.

PedigreeTechnologies.com | Support: (701)-499-0022
10
CameraView
Mitac
STEP ONE
Connect the power plug to the power port on the camera.
Power Cable Port
Test Camera Functionality
STEP ONE
Before securing cabling, check that the camera is
receiving power. Start the truck’s engine.
Blue Power LED
Installation Steps, Continued
Connect Power Cable to Camera
STEP TWO
Check that the blue indicator light on the
front of the camera is on.
Camera with power
cable attached
STEP THREE
Secure the cable by attaching the port
cover and securing with the attached screw
mechanism.

PedigreeTechnologies.com | Support: (701)-499-0022
11
CameraView
Mitac
Installation Steps, Continued
Mount Camera
STEP ONE
Determine proper placement of camera on the front
windshield.
• Center of the windshield next to the rearview
mirror area
• Highest possible placement within the wiper
blade path
• Avoid any overhanging exterior sun visor or
other materials on glass including rock chips
or cracks.
STEP THREE
Clean the mounting area on the windshield with alcohol (not provided). Remove all dirt, oil,
and grime.
STEP TWO
Match the small brackets on the mounting plate
with the knotches on the camera and slide together
to connect.
Mounting Plate back
STEP FOUR
Remove protective plastic on the camera lens. Clean the lens with a soft, lint-free cloth (not
provided). The lens should be free of scratches, dirt, and dust.

PedigreeTechnologies.com | Support: (701)-499-0022
12
STEP FIVE
Orient the camera to the windshield.
• Camera should be level to the horizon line.
• Point the lens forward with a slight downward
angle so the camera picks up the front hood at
the bottom of the frame.
• Rotate the camera lense on the mount to adjust
the position.
• Peel the lm from the mounting plate tape.
STEP SIX
Press the mount rmly to the windshield glass.
CameraView
Mitac
Mount Camera continued
Installation Steps, Continued
Optional Check Camera Position
STEP ONE
On the tablet, open POV, but stay logged out.
STEP TWO
Tap the ellipsis menu in the upper right
corner of POV, and then select “Camera Setup”.
View from camera
STEP THREE
Connect: use this button to search for powered
cameras in your immediate area. Choose
the matching IMEI number from any results
returned.
Standard Camera: keep this eld as “Standard Camera”’
Camera IMEI: use this eld to add the camera’s
IMEI to directly connect to this camera instead of
using the Connect to search. (IMEI number is on the
lable of the camera beneath the mounting plate. Capture this
information before adding mounting plate.)
Once connected, use the horizon guide line to align your front camera and the Driver Face
circle to align your rear facing camera.

PedigreeTechnologies.com | Support: (701)-499-0022
CameraView
Mitac
GOOD MOUNTING TIPS
• Metrics visual detection happens within red square
area (image right)
• Horizon line must be level with more road than sky
• Field of view in green area
• No occulsions in eld of vision.
Good = level horizon, road in range Bad = too much sky
Install Conrmation: 701-499-0022
You will need to call Pedigree Install Support to nalize and conrm the installation.
Mounting Tips
CABIN VIEW
• In cab camera should show driver’s face.
• No obstructions between camera and driver
• Camera should be mounted closer to driver
• Face should be within the example green band
• Must NOT affect driver’s line of sight as per local
regulations