Pedigree Technologies OneView CameraView User manual

INSTALLATION MANUAL
PedigreeTechnologies.com | Support: (701)-499-0022
CameraView (Front Facing Camera)
Document ID: IM-DC-X1
Last Updated: March 24, 2021
Pedigree Technologies recommends using a professional installer for optimal
results. Please let your Pedigree Technologies representative suggest a provider if
you need help with your hardware installations.

2
Prerequisites
PedigreeTechnologies.com | Support: (701)-499-0022
CameraView
Front Facing
Required Information
• Name of asset (ex: Propane Truck #20)
• SN of each device to be installed (Serial number is found on the top of the unit with a QR code)
Standard Equipment
Required Tools
Rubbing Alcohol or Window Cleaner (to clean window surface for best adhesion)
Level (to level camera during mounting)
Drill with Phillps & Torx bits
Small Socket Set
Tablet with POV (Optional: to see live view of camera when setting mounting location)
Camera
Power Module
Before You Begin
TIPS FOR PROPER CAMERA MOUNTING
• Ideal Location: Center (or as close to center as possible) of the windshield.
• Ideal Height: Highest point behind a rearview mirror - in the area swept by the wipers.
• Field of View: Should be clear of any occlustions (EZPass, rear view mirror, etc.)
• Angle: Camera should have a negative pitch angle (it should look “down” a few degrees.)
• The eld of view should not have too much “sky”.
• Split windows may have to adjust mounting location other than what is recommended in this
document. Consult with your implementation manager at Pedigree Technologies.
Tamper
Tape
Micro SD Card
Fuse Tap
Direct Wire Harness
USB Adapter
Alternative
Equipment
Optional

PedigreeTechnologies.com | Support: (701)-499-0022
3
CameraView
Front Facing
Installation Steps, Continued
Determine proper placement of camera on the
front windshield. (Dry t only. It’s important to run
cabling to power source and determine where it will
t properly.)
• High on the windshield behind the rearview mirror
area or right of center divider (slightly to the
passenger side)
• Highest possible placement within the wiper
blade path
• Avoid any overhanging exterior sun visor or other
materials on glass including rock chips or cracks.
Dry Fit
Installation Steps, Continued
Power Cable
Route the cable inside the headliner and A pillar to the power box. (Avoid airbags and other
hardware inside the A pillar.) Cables and wiring should not be visible after installation is complete.

PedigreeTechnologies.com | Support: (701)-499-0022
4
Installation Steps, Continued
Standard Direct Wire Installation
CameraView
Front Facing
STEP ONE
Connect the ground (black) wire of the direct wire harness to DC chassis ground.
• It may be necessary to crimp a ring terminal to the ground wire.
• Always connect the ground wire to an already established ground stud when possible.
• The frame of the vehicle is an acceptable ground point if ground studs are not available.
• The surface area must be clean and free of paint, rust, or anything that will cause the
connection to fail.
Black - Ground
Red - Power
STEP THREE
Connect the micro USB cable to the camera.
STEP TWO
Connect the power (red) wire to ignition (or other 12V power source that is powered on when the
ignition is on).
(Optional) Power to Fuse Tap
It may be necessary to connect the power wire to a
blade fuse adapter.
• Crimp the power wire in the open end of the
adapter
• Remove the ACC fuse and insert it into the fuse
adapter (maximum 10 Amps)
• Plug the adapter into the open ACC fuse slot

PedigreeTechnologies.com | Support: (701)-499-0022
5
CameraView
Front Facing
Alternative Option - APMM Power Module Installation for Cab-Mate One
STEP ONE
Identify and record the ESN of the Cab-Mate One
before proceeding. The following steps will cover
the serial number and you will need it for activating
the device later, or servicing the device in the future.
STEP TWO
For new intalls of the Cab-Mate One, install
the diagnostic data cable as per the Cab-Mate
One installation document. DO NOT CONNECT
DIAGNOSTIC CABLE TO CRADLE YET
STEP THREE (for new Cab-Mate One installs)
Remove the ball mount from the Panavise mount.
With the other side (the long piece) locate the
desired position on the dash of vehicle and secure
with hardware.
Secure to Dash
Secure to tablet in
step ve
Panavise Mount
STEP THREE (for previously installed Cab-Mate One)
Remove the ball mount from the Panavise mount and remove from the back of the tablet by
removing the 4 fastening screws.
STEP FOUR
Dry t CameraView module as per the installation instructions (page 3 of this document), routing
the USB cable to the Cab-Mate One, but do not plug it into the APMM module yet.

PedigreeTechnologies.com | Support: (701)-499-0022
6
CameraView
Front Facing
Alternative - APMM Power Module Installation for Cab-Mate One continued
STEP FIVE
Secure the APMM bracket to the Cab-Mate One by sandwiching it between the Cab-Mate One
and the ball mount using the supplied screw and washer pack. (Use the longer machine screws
provided, paired with star washers.)
+ +
STEP SIX
Secure the APMM module to bracket using the supplied double-sided tape with the text side
facing up as pictured below.
+ =
Ball Mount APMM Bracket Cab-Mate One
STEP SEVEN
Connect the 16pin and 6 pin plugs of the APMM harness to the ports on the bottom of the Cab-
Mate One. (For previously installed Cab-Mate One, remove 16 pin connector from bottom of Cab-
Mate One and replace with the APMM harness.)
APMM Harness
Bottom view

PedigreeTechnologies.com | Support: (701)-499-0022
7
CameraView
Front Facing
Alternative - APMM Power Module Installation for Cab-Mate One continued
STEP EIGHT
Connect the APMM harness to the AUX1 and LMU DIAG ports on the top of the APMM module.
STEP NINE
Mount the Cab-Mate One/APMM
assembly to the dash using the Panavise
ball mount (not pictured).
STEP TEN
Connect the diagnostic cable to the port
on the APMM labled “VEHICLE DIAG” on
the bottom of the APMM module.
STEP ELEVEN
Connect the CameraView USB cable to the
USB adapter cable.
Top view
Bottom view
STEP TWELVE
Connect the 10 pin plug from the USB
adapter cable into the port on the side
of the APMM power module.

PedigreeTechnologies.com | Support: (701)-499-0022
8
CameraView
Front Facing
Alternative Option - APMM Power Module Installation for CalAmp LMU 3640
STEP ONE
For a previously installed LMU 3640, unplug the
diagnostic cable from the LMU.
STEP TWO
Plug the longer 16-pin plug from the APMM
harness into the 16 pin port on the LMU, replacing
the diagnostic cable you just removed if working on
previously installed LMU.
STEP THREE
Plug the male 5 pin plug from the APMM harness
into the female 5 pin plug of the accessory harness.
OPTIONAL STEP
If this is a new installation of the LMU 3640, plug
the 20 pin plug of the accessory harness into the
20 pin port of LMU.
Remove Existing
Diagnostic Cable
APMM Harness
Male 5 pin from
APMM Harness
Female 5 pin
from Accessory
Harness

PedigreeTechnologies.com | Support: (701)-499-0022
9
CameraView
Front Facing
STEP FOUR
Plug the 16 pin plug from the short end of the
APMM harness into the LMU DIAG port on the
power module.
STEP FIVE
Plug the 6 pin plug from the APMM harness into
the AUX 1 port on the power module.
STEP SIX
Plug the diagnostic cable (from STEP ONE) into the
VEHICLE DIAG. port on the power module.
STEP SEVEN
Plug the usb adapter cable into the 10 pin port on
the side of the power module.
Alternative APMM Power Module Installation - CalAmp LMU 3640 continued...
APMM Harness
Power Module
Diagnostic Cable
Power Module
Camera USB
Power Cable
STEP EIGHT
Conect the usb adapter cable to the USB end of the
camera USB power cable. Connect the power end
to the camera (pictured on p11.)

PedigreeTechnologies.com | Support: (701)-499-0022
10
Test Camera Functionality
STEP ONE
Start the truck’s engine.
STEP TWO
Make sure that the camera has power (indicated by
the blue LED next to the camera lens, may take 30-45
seconds to receive power). Blue LED next to camera lens
CameraView
Front Facing
STEP THREE
On the tablet, open POV, but stay logged out.
STEP FOUR
Tap the 3-dots menu in the upper right corner of POV, and then select “Camera Setup”.
STEP FIVE
The app will look for cameras near you, and
as long as there is power to your camera,
the app will nd it. It will take 30 to 60
seconds to nd and connect the camera.
Once it connects, you will see the view from
the camera, allowing you to adjust angle if
necessary.
View from camera
GOOD MOUNTING TIPS
• Metrics visual detection happens within red square
area (image on right)
• Horizon line (in red below) must be level with more
road than sky
• Field of view in green area
• No occulsions in eld of vision.
Good = level horizon, road in range
BAD MOUNTING
• Too much of the sky is visible.
Bad = too much sky