peerless-AV SS560FK Guide

Installation and Assembly:
32" - 65" (81 - 165 cm) Kiosk Stand
Models: SS560FK
ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerless-av.com
Max UL Load Capacity:
150 lb (68 kg) display
15 lb (6.8 kg) component
Suitable For Institutional Use

2 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List............................................................................................................................................................................ 3, 4
Assembling Stand...................................................................................................................................................................5
Installing Adapter Brackets to Flat Panel Display...................................................................................................................7
Mounting Flat Panel Display...................................................................................................................................................9
Cable Management................................................................................................................................................................9
Tools Needed for Assembly
• phillips screwdriver
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands
these instructions.
• Never exceed the Maximum UL Load Capacity on page 1. Use with heavier televisions may result in instability
causing tip over resulting in death or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• The cart or stand is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand
is shaken or hit. Not recommended for use in areas with heavy traffic.
• Death or serious injury may occur when children climb on audio and/or video equipment furniture. Aremote control
or toys placed on the furnishing may encourage a child to climb on the furnishing resulting in the furnishing tipping
over on to the child.
• Relocating audio and/or video equipment from this cart or stand to furniture not specifically designed to support
audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or over turning
onto a child.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
WARNING

3 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
Before you begin, make sure all parts shown are included with your product.
Parts List
Description Qty. Part Number
A
base 1 009-1425
Bcolumn 1 009-1426
Ccolumn bracket 1 009-1424
Dtilt plate 1 009-1423
Eadapter plate 1 201-1110
Fadapter bracket 2 202-1655
H3/8-16 x 1" button socket cap screw 3 520-1354
I5/16"-18 x 3/8" button socket cap screw 4 520-1693
JM10 lock washer 3 540-9424
KM10 x 15 mm button socket cap screw 4 520-9262
L3/8-16 X 2-1/2" button socket cap screw 3 520-9550
M6 mm allen wrench 1 560-9716
N7/32" allen wrench 1 560-9715
O3/16" allen wrench 1 560-0071
Ptop plate 1 201-1724
Qbottom plate 1 201-1699
Rrubber feet (pack of four) 1 570-1036
SM8 x 15mm socket pin screw 4 520-1068
TM10 x 15mm penta-pin screw 4 520-9263
UM10 penta-pin tool 1 520-9260
V4mm allen wrench 1 560-9646
Parts may appear slightly different than illustrated.
ABCD
H
L
J
K
I
F
M
N
O
E

4 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
PQRST
UV
M5 x 25mm (4)
(520-1122)
M5 x 12mm (4)
(520-1064) M6 x 12mm (4)
(520-1050)
M6 x 25mm (4)
(520-1211) M8 x 25mm (4)
(520-1101)
M8 x 12mm (4)
(520-1724) .75" spacer (4)
(540-1059)
Multi-washer (4)
(580-1398)
Security Adapter Bracket Fasteners

5 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
Attach column (B) to base (A) with three
3/8-16 x 2-1/2" button socket cap screws (L) and
three M10 lock washers (J). Tighten screws using
7/32" allen wrench (N).
1
A
LJ
B
Attach tilt plate (D) to bottom plate (Q) with four
M10 x 15 mm button socket cap screws (K).
Tighten screws using 6 mm allen wrench (M).
Attach the column bracket (C) to column (B) with
three 3/8-16 x 1" button socket cap screws (H).
Tighten screws using 7/32" allen wrench (N).
Attach tilt plate (D) to column bracket (C) with four
5/16-18 x 3/8" button socket cap screws (I) as
shown in rear view.
Tilt can be adjusted to 0° or 30°.
3
2
4
REAR VIEW
D
K
D
Q
C
C
I
H
B

6 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
Attach top plate (P) to adapter plate (E) with four
M10 x 15 mm penta-pin screws (T).
Tighten screws using penta-pin tool (U).
Secure four rubber feet (R) to bottom of CPU as
shown below.
Secure CPU to top plate (P) using safety belt.
NOTE: Safety belt may need to be loosened to
attach CPU to component box top plate.
Secure top plate (P) to bottom plate (Q) with four
M8 x 15 mm screws (S) as shown in rear view.
Tighten screws using 4 mm allen wrench (V).
5 6
7
REAR VIEW
E
TR
P
P
S Q
P
CPU
CPU
SAFETY BELT
CPU MAYAPPEAR
DIFFERENT THAN
ILLUSTRATED
6-1

7 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
NOTE: "X" dimensions should be equal.
Installing Adapter Brackets to Flat Panel Display
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display. Place
display face side down. Refer to display manufacturers instructions or customer service, for removing any knobs,
base, cover, or screw(s) on the back of the display to prepare mounting. These need to be removed to allow the
adapter brackets (F) to be attached. Select the small, medium, large or extra large screws from the baffled fastener
pack then attach adapter brackets to display following figure 8.1 or 8.2.
NOTE: Top and bottom mounting holes must be used for attaching adapter brackets. Verify that all holes are
properly aligned, and then tighten screws using 4 mm security allen wrench (BB).
FCENTER BRACKETS
VERTICALLY ON BACK
OF DISPLAY
X
X
8
Notes:
• The number of fasteners used will vary,
depending upon the type of display.
• Multi-washers and spacers may not be
used, depending upon the type of display.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
MULTI-WASHER
NOTE: For flat back displays proceed to step 8-1. For bump-out or recessed back display skip to step 8-2.
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and adapter brackets are still
not tightly secured, damage may oXur to display or product may fail.
WARNING

8 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as
shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not
over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into
display as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place.
Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the
baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
8-1
8-2
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
DISPLAY
MULTI-WASHER
SCREW
ADAPTER
BRACKET (F)
fig. 8.2
SPACER
ADAPTER
BRACKET (F)
DISPLAY
fig. 8.1
MULTI-WASHER
SCREW

9 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
Run cables through column (B) using cable
management holes.
Mounting Flat Panel Display
Hook adapter brackets (F) onto adapter plate (E).
Then slowly swing display down as shown. Turn
security screws, using 4 mm security allen wrench
(V), clockwise at least six times to prevent display
from being removed as shown in detail 1 of figure
9.1.
NOTE: To lock the display down, tighten security
screws to adapter plate (E) as shown in detail 1.
9 10
Cable Management
© 2014, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerless-av.com
fig 9.1
DETAIL 1
E
SECURITY
SCREWS
CABLE
MANAGEMENT
HOLES
F
B
Service and Maintenance
This product has no user serviceable parts.
11

10 of 10 ISSUED: 09-30-11 SHEET #: 009-9056-5 (2014-04-08)
© 2014 Peerless Industries, Inc.
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
using or storing the product, or (d) misuse or aXident, in transit or otherwise, including in cases of third party actions and force majeure.
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
This warranty gives specific legal rights, and you may also have other rights which vary from state to state.
LIMITED FIVE-YEAR WARRANTY
www.peerless-av.com