peerless-AV ACC-MB10 User manual

12013-10-8 #:125-9469-1
ENG
200 lb
(90 kg)
MAX
ACC-MB10

22013-10-8 #:125-9469-1
This page intentionally left blank.
ENG

32013-10-8 #:125-9469-1
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Tools Needed for Assembly.
ENG
3/8"
(10mm)
Symbols
ENG
WARNING
ENG
#
Skip to step.
ENG
Display center.
ENG
x3
Screws must get at least three
full turns and t snug.
ENG
Do not overtighten screws.
ENG
5/32"
(4mm)
5/16"
(8mm)

42013-10-8 #:125-9469-1
ENG - This product is designed to be installed on wood stud, solid concrete or cinder block walls. Hardware is
included for wood stud, solid concrete and cinder block installation. Before installing make sure the supporting
surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do
not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Be
careful not to pinch ngers when operating the mount. For support please call customer care at 1-800-865-2112.
WARNING
Parts (Before beginning, make sure you have all parts).
ENG
Parts List
Part Description QTY Part #
Awall plate 1202-1604
Bconcrete anchor 4590-0320
C#14 x 2.5" wood screw 45S1-015-C03
Dadapter bracket 1202-1612
EM5 x 6mm phillips screw 4520-1023
F#10 at washer 4540-9400
B (4)
8mm concrete anchor
C (4)
#14 x 2.5" wood screw adapter bracket
D (1)
M5 x 6mm
E (4)
#10 at washer
F (4)
A (1)
wall plate

52013-10-8 #:125-9469-1
A
D
F
E
Optional: Additional ACC-MB10 mounts sold separately
1

62013-10-8 #:125-9469-1
2
2b-12a-1
Wood stud wall.
ENG Concrete/Cinder block. ENG
ENG - When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that
the woods studs are a minimum of 2" x 4" nominal size. When installing to more than one stud, ensure the
spacing between studs is at least 16" but does not exceed 24". Do not install over gypsum board thicker than 5/8".
WARNING

72013-10-8 #:125-9469-1
2a-2
Level wallplate. Mark mounting holes on stud
center lines.
ENG
2a-1
Use stud nder to locate and mark stud
center lines.
ENG

82013-10-8 #:125-9469-1
2a-3
Mounting hole must center on stud.
ENG
5/32"
(4mm)
Drill mounting holes into supporting surface
(2.5" (64 mm) minimum depth required).
ENG
2
2.5"
(64mm)
5/32"
(4mm)
2a-4
Level wallplate. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
C (2)

92013-10-8 #:125-9469-1
2b
ENG • When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi.
• When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90
specications and have a minimum nominal width of 8". Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" (25 mm) minimum from the side of the block. It is suggested that a standard electric
drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole
when entering a void or cavity.
• Never attach expansion anchors to concrete or cinder block covered with plaster, drywall or other nishing
material.
WARNING

10 2013-10-8 #:125-9469-1
2.5"
(64mm)
5/16"
(8mm)
2b-1
2b-2
Level wallplate. Mark mounting holes.
ENG
5/16"
(8mm)
Do not drill into mortar joints.
ENG
Drill mounting holes into supporting surface
(2.5" (64 mm) minimum depth required).
ENG