peerless-AV PLCK-UNL Guide

ISSUED:02-22-07 SHEET #: 202-9197-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
1 of 5
Read instruction sheet before you start installation and assembly.
Model:PLCK-UNL
Maximum Load Capacity:
125 lb (57 kg)
Installation and Assembly -Flat Panel Conversion Kit
with Universal Adapter Plate
TABLE OF CONTENTS
Installation
PartsList.....................................................page2
InstallationofAdapter
Brackets.....................................................page3
Mounting and Removing Flat Panel
Screen........................................................page5
• Installer must verify that the wall will safely support the
combinedweightofall attachedequipment and
hardware.
WARNING

ISSUED:02-22-07 SHEET #: 202-9197-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
2 of 5
BBAA
M5 x 25 mm (4)
520-1122
M4 x 12 mm (6)
510-1079
M4 x 25 mm (4)
510-1082
M5 x 12 mm (4)
520-1064 M6 x 12 mm (4)
520-1050
M6 x 25 mm (4)
520-1211
I.D. 5.6 mm (4)
540-1057
multi-washer(6)
580-1036
I.D. 8.7 mm (4)
540-1059
Security Adapter Bracket Fasteners
M6 x 20 mm (4)
520-9554
M6 x 30 mm (4)
520-1067
M8 x 15 mm (6)
520-1068
M8 x 40 mm (4)
520-1152
M8 x 25 mm (4)
520-1101
Description Qty Part #
AA adapter plate 1 201-1109
BB deep bracket 2 200-0752
Before you begin, make sure all parts shown are included with your product.
PARTS LIST

ISSUED:02-22-07 SHEET #: 202-9197-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
3 of 5
Note: "X"dimensions shouldbeequal.
• Tightenscrewsso deepbrackets are firmly
attached. Do not tighten with excessive force.
Overtighteningcan causestressdamageto
screws,greatly reducingtheir holdingpower and
possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.)
maximumtorque.
WARNING
Installing Adapter Brackets
Refer to Screen Compatibility Chart to determine the proper fasteners to use.
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place deep brackets (BB) on back of screen, align to holes, and center on back of screen as shown in figure 1.1.
Attach the deep brackets to the back of the screen using the appropriate combination of screws, multi-washers, and
spacers as shown in figure 1.3.
Note: Top and bottom holes must always be used.
Verify that all holes are properly aligned, and then tighten screws using a4mmallenwrench(includedinACC109).
• If screws don't get three complete turns in the screen
inserts or if screws bottom out and bracket is still not
tightly secured, damage may occur to screen or
productmayfail.
WARNING
MEDIUMHOLEFORM5SCREWS
SMALLHOLEFORM4SCREWS
LARGEHOLEFORM6SCREWS
fig. 1.2
BB
CENTERBRACKETS
VERTICALLYONBACKOF
SCREEN
X
X
fig 1.1
Notes:
• Thenumber offasteners usedwillvary,
dependingupon thetypeofscreen.
• Multi-washers and spacers may not be
used,dependinguponthetype ofscreen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
showninfigure 2.2.
SCREWS
SPACERS
BB
fig 1.3
MULTI-
WASHER
MULTI-WASHER
1

ISSUED:02-22-07 SHEET #: 202-9197-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
4 of 5
Hang tilt bracket onto ceiling arm box (included in PLCM-2).Adjust tilt as desired and tighten four M10 x 1.5 x 15 mm
penta-pinscrews(includedinPLCM-2) securelyusing M10penta-pin tool(includedinPLCM-2).
Attach tilt bracket to adapter plate (AA) using four M10 x 15 mm penta-pin screws (included in PLCM-2) in accordance
withappropriate drawingbelow.TightenusingM10 penta-pintool (includedin PLCM-2).
LANDSCAPE
Note:Screen andadapter
platemay appeardifferent
thanillustrated.
• For a safe assembly be sure to fully tighten four M10
x15mm penta-pinscrews(included inPLCM-2).
WARNING
2
3
TILTBRACKET
M10X15 mm
PENTA-PIN
SCREWS
CEILINGARMBOX
M10X15 mm
PENTA-PIN
SCREWS
TILTBRACKET
AA

ISSUED:02-22-07 SHEET #: 202-9197-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
5 of 5
Mounting and Removing Flat Panel Screen
Hook deep brackets (BB) onto adapter plate (AA), then slowly swing screen in as shown. Turnscrewsclockwiseat
leastsixtimes toprevent screenfrom beingremoved asshownin detail1.
Note:Tightenusing4mmallenwrench(includedinACC109).
Screen can be adjusted horizontally if desired.
Note: It is important to lock screen down! To lock the screen down, tighten screws to deep bracket as shown in
detail1.
Toremovescreenfrommount,loosenscrews,swingscreenawayfrommount, andliftscreenoffofmount.
BB
DETAIL 1
SCREWS
AA
BB
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
WARNING
AA
©2007PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
4