peerless-AV KIL742 User manual

12015-04-28 #:150-9053-1
ENG
BLACK
KIL740
KIL742
KIL746
KIL747
KIL748
KIL755
SILVER
KIL740-S
KIL742-S
KIL746-S
KIL747-S
KIL748-S
KIL755-S

22015-04-28 #:150-9053-1
Symbols
ENG
WARNING
ENG x3
Screws must get at least three
full turns and fit snug.
ENG
Do not overtighten screws.
ENG
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. This product is designed to be installed on wood stud walls. Hardware is included
for wood stud installation. Before installing make sure the supporting surface will support the combined load of
the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur
and product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting
equipment to safely lift and position equipment. This product is intended for indoor use only. Use of this product
outdoors could lead to product failure or personal injury. To reduce the risk of electric shock or fire, do not
expose product to water or moisture. Be sure power cord is routed so that it will not be tripped on, stepped on,
or pinched by heavy items. Avoid overloading electrical outlets or extension cords. Always disconnect the power
cord from the power outlet when installing, servicing, or not using the product for an extended period of time. Do
not block ventilation slots or fan exhaust on product. Blocking airflow could damage product. Arrange product
to allow air to flow freely around product. Keep product away from direct sunlight or any source of heat. For
support please call 800-4-SIGNAGE.
WARNING
ENG Always use an assistant
or mechanical lifting
equipment to safely lift
and position equipment.

32015-04-28 #:150-9053-1
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
+1/2
4
3

42015-04-28 #:150-9053-1
Parts (Before beginning, make sure you have all parts shown below).
ENG
A (1)
L (1)
back shroud
front shroud
B (4)
M5 x 12 mm C (4) M5 x 25 mm
D (4)
M6 x 12 mm E (4) M6 x 25 mm
M5/M4/M6 washer
H (4)
M8 x 12 mm
F (4) M8 x 25 mm G (4)
spacer
I (4)
K (1) J (2)allen
wrench
M5 x 20mm
M (4)
#14 x 2-1/2" wood screw N (2)
adapter bracket
O (1)
power strip cable tie
P (6)

52015-04-28 #:150-9053-1
2
xx"
yy"
1
KIL740, KIL742
KIL746, KIL747, KIL748
KIL755
XX = 43.25, YY = 27.5
XX = 48.25, YY = 30.25
XX = 55.75, YY = 33.75

62015-04-28 #:150-9053-1
Mark mounting holes.
ENG
7
5/32"
(4 mm)
2.5"
(64mm)
5/32"
(4mm)
Drill four mounting holes.
ENG
6

72015-04-28 #:150-9053-1
M (4)
8

82015-04-28 #:150-9053-1
9
B (4)
I (4)
H (4)
G(4) D (4) H (4)
G (4)
I (4)
I (4)
H (4)
F (4)
X
X
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
Use of spacers is OPTIONAL.
Uso de espaciadores OPCIONAL.
FACULTATIF utilisation d’entretoises.
OPTIONAL Verwendung von Abstandhaltern.
FACULTATIEF gebruik van tussenringen.
Uso OPZIONALE di distanziatori.
VOLITELNÉ použití rozpěr.
VOLITEĽNÉ použitie rozpierok.
OPCIONAL utilize espaçadores.
Ayırıcıların İSTEĞE BAĞLI kullanımı.
x3
Screws must get at least three full turns and fit snug.
Los tornillos tienen que dar, por lo menos, tres vueltas completas y quedar ajustados.
Il faut effectuer au moins trois tours de vis complets et bien serrer les vis.
Schrauben sind mindestens drei volle Umdrehungen einzudrehen und müssen fest anliegen.
De schroeven moeten ten minste drie hele slagen worden aangedraaid en stevig vastzitten.
Girare tre volte le viti che devono risultare aderenti.
Šrouby se musí otočit minimálnětři plné otáčky a plnědosednout.
Skrutky sa musia otočiťaspoňtri celé otáčky a tesne dosadnúť.
Os parafusos devem completar, no mínimo, três voltas completas e ajustar-se no local.
Vidalar en az üç tam dönüşyapmalıve sıkıoturmalıdır.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
Center adapter brackets vertically on back of screen.
Centre verticalmente los soportes en la pantalla.
Centrez les supports à la verticale de l’écran.
Richten Sie die Halterungen senkrecht mittig an der
Bildschirm.
Centreer de beugels verticaal op de van het scherm.
centra le staffe verticalmente sul dello schermo.
vycentrujte konzoly svisle na zadní obrazovky.
vycentrujte konzoly zvisle na obrazovky.
centre os suportes verticalmente no do ecrã.
dirsekleri ekranın arkasına dikey olarak ortalayın.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
E (4)
H (4)

92015-04-28 #:150-9053-1
10
11

10 2015-04-28 #:150-9053-1
1212
A
J (2)
13
L
Note: Mounting Arm swings out to access
adapter brackets and behind display
ENG