peerless-AV DS-C555-3X3 User manual

12014-05-30 #:009-9086-9 (2019-09-04)
ENG
DS-C555-3X3
46" - 55"
(117 - 140 cm)
900 lb
(409 kg)
MAX

22014-05-30 #:009-9086-9 (2019-09-04)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
Display center.
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Do not overtighten screws.
ENG
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product must be installed onto at, hard, level surface to prevent tipping. Use with heavier
displays may result in instability causing tip over resulting in death or serious injury. The cart or stand is not
a󰀩xed or secured to the oor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit.
Displays must be removed before moving cart. Not recommended for use in areas with heavy tra󰀩c. This product
is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury.
Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never
exceed the Maximum Load Capacity. Be careful not to pinch ngers when operating the mount. Death or serious
injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed
on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on
to the child. Relocating audio and/or video equipment to furniture not specically designed to support audio and/
or video equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a
child. For support please call customer care at 1-800-865-2112.
WARNING
ENG

32014-05-30 #:009-9086-9 (2019-09-04)
This page intentionally left blank.ENG

42014-05-30 #:009-9086-9 (2019-09-04)
Parts (Before beginning, make sure you have all parts shown below).
Parts List
Part #Description Qty
Acaster, 5" swivel 4 600-0026
Bcaster support 4 145-T1799
Ccover 6 145-T1809
Dbase leg 2 145-T1767
Ehorizontal leg support 1 145-T1785
Fbase support tube 2 145-T1812
Gbase support 8 560-T1261
Hvertical leg support 2 146-T1131
Ileg support extension 2 145-T1778
Jleft adaptor bracket 9 146-1609
Kright adaptor bracket 9 146-1608
Lside support bracket 4 145-T1807
Mvertical support bracket 6 145-T1806
Ncomputer cover 1 145-T1930
Ocomputer shelf 1 145-T1931
Pdual cross support 3 146-T1905
Qcross support 3 146-T1904
Rextension adaptor 2 145-T1935
Scord bracket 4 146-T1321
Tknurled knob 4 560-1160
Uplate connections 6 145-T1821
VM8 x 16mm socket button screw 176 520-9527
WM8 square nut 66 530-1066
Xcover clip 24 590-0317
YM5 x 10mm type-F, socket pin screw 20 520-1164
Zbar nut 20 146-1319
AA 1/4" power bit 1 560-0263
BB 5mm allen wrench 1 560-9640
CC nylon shoulder washer 36 590-2233
DD M6 x 12mm socket pin screw 36 520-1050
EE 4mm allen wrench 1 560-9646
FF M8 x 20mm screw 6 520-1754
A (4)
caster
B (4)
caster support
C (6)
cover
D (2)
base leg
E (1)
horizontal leg
support
F (2)
base
support tube
G (8)
base support
H (2)
vertical leg
support
M (6)
vertical support
bracket
L (4)
side support
bracket
I (2)
leg support
extension
K (9)
right adaptor
bracket
J (9)
left adaptor
bracket
ENG

52014-05-30 #:009-9086-9 (2019-09-04)
Q (3)
cross support
EE (1)
4mm allen
wrench
N (1)
computer cover
P (3)
dual cross
support
V (176)
M8 x 16mm
W (66)
M8 square
nut
X (24)
cover clip
Y (20)
M5 x 10mm
AA (1)
1/4" power bit
BB (1)
5mm allen
wrench
CC (36)
nylon shoulder
washer
DD (36)
M6 x 12mm
U (6)
plate
connections
R (2)
extension
adaptor
O (1)
computer shelf
S (4)
cord
bracket
T (4)
knurled
knob
bar nut
Z (20)FF (6)
M8 x 20mm

62014-05-30 #:009-9086-9 (2019-09-04)
1-1
1-2
V (4)
A
B
V (2)
W (2)
Do not fully tighten hardware
SIDE VIEW
x4
x4
BB
BB
ENG

72014-05-30 #:009-9086-9 (2019-09-04)
2
V (4)
V (4)
F
F
W (4)
W (4)
D
W (4)
x2 BB

82014-05-30 #:009-9086-9 (2019-09-04)
Casters must be ush to end of horizontal leg support.
ENG
4
SIDE VIEW
Do not fully tighten hardware
x8 Z (2)
G
V (4)
3
TIGHTEN
CONNECTING
HARDWARE
Flush edges
ENG
x2 BB
BB
ENG
D

92014-05-30 #:009-9086-9 (2019-09-04)
x2
5
H
TIGHTEN
CONNECTING
HARDWARE
TIGHTEN
CONNECTING
HARDWARE
6
E
LOCK WHEELS
BB
BB
ENG

10 2014-05-30 #:009-9086-9 (2019-09-04)
7-1
Do not fully tighten hardware
V (4)
Z (2)
R
TOP VIEW
x2
I (2)
R (2)
TIGHTEN
CONNECTING
HARDWARE
7-2
BB
BB
ENG