peerless-AV DS-C555-4X3 User manual

12015-06-24 #:009-9118-6 (2019-09-04)
ENG
DS-C555-4X3
46" - 55"
(117 - 140 cm)
1200 lb
(545 kg)
MAX

22015-06-24 #:009-9118-6 (2019-09-04)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
Display center.
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Do not overtighten screws.
ENG
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product must be installed onto at, hard, level surface to prevent tipping. Use with heavier
displays may result in instability causing tip over resulting in death or serious injury. The cart or stand is not
a󰀩xed or secured to the oor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit.
Displays must be removed before moving cart. Not recommended for use in areas with heavy tra󰀩c. This product
is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury.
Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never
exceed the Maximum Load Capacity. Be careful not to pinch ngers when operating the mount. Death or serious
injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed
on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on
to the child. Relocating audio and/or video equipment to furniture not specically designed to support audio and/
or video equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a
child. For support please call customer care at 1-800-865-2112.
WARNING
ENG

32015-06-24 #:009-9118-6 (2019-09-04)
This page intentionally left blank.ENG

42015-06-24 #:009-9118-6 (2019-09-04)
Parts (Before beginning, make sure you have all parts shown below).
I (3)
extension
A (6)
caster
B (6)
caster support
C (9)
cover
D (3)
base leg
E (2)
horizontal leg
support
F (3)
base
support tube
G (14)
base support
H (3)
vertical leg
support
J (4)
side support
bracket
Parts List
Part #
Description Qty
Acaster, 5" swivel 6 600-0026
Bcaster support 6 145-T1799
Ccover 9 145-T1809
Dbase leg 3 145-T1767
Ehorizontal leg support 2 145-T1785
Fbase support tube 3 145-T1812
Gbase support 14 560-T1261
Hvertical leg support 3 146-T1131
Iextension 3 145-T1778
Jside support bracket 4 145-T1807
Kleft adaptor bracket 12 146-1609
Lright adaptor bracket 12 146-1608
Mvertical support bracket 6 145-T1806
Ndual cross support 6 146-T1905
Ocomputer cover 1 145-T1930
Pcomputer shelf 1 145-T1931
Qextension adaptor 3 145-T1935
Rcord bracket 6 146-T1321
Sbracket, 4x2 conguration 3 145-T1858
Tknob 6 560-1160
UM8 x 16mm socket button screw 244 520-9527
VM8 square nut 80 530-1066
Wcover clip 36 590-0317
XM5 x 10mm type-F, socket pin screw 26 520-1164
Ybar nut 34 146-1319
Z1/4" power bit 1 560-0263
AA 5mm allen wrench 1 560-9640
BB nylon shoulder washer 48 590-2233
CC M6 x 12mm socket pin screw 48 520-1050
DD 4mm allen wrench 1 560-9646
L (12)
right adaptor
bracket
K (12)
left adaptor
bracket
ENG

52015-06-24 #:009-9118-6 (2019-09-04)
O (1)
computer cover
P (1)
computer shelf
S (3)
bracket, 4x2
conguration
N (6)
dual cross
support
DD (1)
4mm allen
wrench
U (244)
M8 x 16mm
V (80)
M8 square
nut
W (36)
cover clip
X (26)
M5 x 10mm
Z (1)
1/4" power
bit
AA (1)
5mm allen
wrench
BB (48)
nylon shoulder
washer
CC (48)
M6 x 12mm
Q (3)
extension
adaptor R (6)
cord
bracket
T (6)
knob bar nut
Y (34)
M (6)
vertical support
bracket

62015-06-24 #:009-9118-6 (2019-09-04)
1-1
1-2
U (4)
A
B
U (2)
V (2)
Do not fully tighten hardware
SIDE VIEW
x6
x6
AA
AA
ENG

72015-06-24 #:009-9118-6 (2019-09-04)
2
U (4)
U (4)
F
F
V (4)
V (4)
D
V (4)
x3 AA

82015-06-24 #:009-9118-6 (2019-09-04)
3
TIGHTEN
CONNECTING
HARDWARE
Flush edges
ENG
Casters must be ush to end of horizontal leg support.
ENG
4
Y (2)
G
U (4)
SIDE VIEW
Do not fully tighten hardware
x14
x3
AA
AA
ENG
D

92015-06-24 #:009-9118-6 (2019-09-04)
x2
5-2
H
TIGHTEN
CONNECTING
HARDWARE
5-1
H
TIGHTEN
CONNECTING
HARDWARE
AA
AA

10 2015-06-24 #:009-9118-6 (2019-09-04)
6-1
6-2
U (4)
Y (2)
Q
I (3)
Q (3)
TIGHTEN
CONNECTING
HARDWARE
x3 Do not fully tighten hardware
AA
AA
ENG
TOP VIEW