peerless-AV GC-X360S-W Instruction manual

1date:01/22/13 #:125-9401
GC-X360S-W
GC-X360S-B
Game Console Security
Cover for Xbox 360S

2date:01/22/13 #:125-9401
ENG - This product was designed to be installed on wood stud, solid concrete or cinder block walls. Before in-
stalling make sure the supporting surface will support the combined load of the equipment and hardware. Screws
must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed
the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product is intended for indoor use only. Use of this product outdoors could lead to product failure
or personal injury. For support please call customer care at 1-800-865-2112.
WARNING
Symbols
WARNING
#
Skip to step.
Display
center.
x3
Screws must get at
least three full turns
and t snug.
Do not over tighten screws
1
2
To properly tighten screws: Tighten until screw head
makes contact, then tighten another 1/2 turn. Do not
overtighten screws.
+1/2
4
3

3date:01/22/13 #:125-9401
Tools Needed for Assembly.
3/8"
(10mm)
5/16",
5/32", 1/2"

4date:01/22/13 #:125-9401
A
Parts List
Part Description Quantity Part Number (-B) Part Number (-W)
Acover plate 1 125-P1455 125-2455
B1/4-20 x 1.75" carriage bolt 4 520-1017 520-1017
C#14 2 2.5" hex head wood screw 2 500-1005 500-1005
D1/4-20 x 1.5" socket pin screw 4 520-1256 520-1256
Econcrete anchor 2 590-0320 590-0320
F1/4 x 20 slope nut 3 530-0035 530-0035
Gplastic screw cap 4 590-1294 590-1294
H4 mm allen wrench 1 560-9646 560-9646
I1/4-20 plastic toggler 4 560-9708 560-9708
J1/4-20 nylock nut 2 530-9413 530-9413
Before beginning, make sure you have all parts shown below
BC
F
DE
H
G
I
J

5date:01/22/13 #:125-9401
1
1b
Wood stud wall.
Drywall. Desktop
Concrete/Cinder block.
1a
1c 1d

6date:01/22/13 #:125-9401
1a-2
1a-1
Use stud nder to locate and mark stud
center lines.
Level cover plate. Mark mounting holes
on stud center lines.
When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that the
woods studs are a minimum of 2”X4” nominal size. When installing to more than one stud, insure the spacing
between studs is at least 16” but does not exceed 24”. Do not install over gypsum board thicker than 5/8”.
WARNING
1a

7date:01/22/13 #:125-9401
1a-3
1a-4
Level cover plate. Install using wood screws provided.
5/32"
(4mm)
3/8"
(10mm)
Drill mounting holes into supporting surface
(2.5" (64 mm) minimum depth required).
2
Mounting hole must center on stud.
2.5"
(64mm)
5/32"
(4mm)
Maximum 80 in. • lb (9 N.M.).
C

8date:01/22/13 #:125-9401
ENG • When installing Peerless wall mounts on a concrete wall, the wall must be at least 8” thick with a minimum
compressive strength of 2000 psi.
• When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90
specications and have a minimum nominal width of 8”. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1” (25 mm) minimum from the side of the block. It is suggested that a standard electric
drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole
when entering a void or cavity.
• Never attach expansion anchors to concrete or cinder block covered with plaster, drywall or other nishing
material.
WARNING
1b
1b-1
Level cover plate. Mark mounting holes.
1b-2
5/16"
(8mm)
Do not drill into mortar joints.
Drill mounting holes into supporting surface
(2.5" (64 mm) minimum depth required).
2.5"
(64mm)
5/16"
(8mm)

9date:01/22/13 #:125-9401
1b-31b-3
1b-41b-4
Level wallplate. Install using concrete
anchors and wood screws provided.
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
Insert anchor ush to concrete.
C
E
E

10 date:01/22/13 #:125-9401
Rotate toggler (I) clockwise to wedge it against
inside walls.
Push into hole.
Pivot end of toggler (I).
Slide plastic cap forward while pulling back
rmly on ring.
Break off excess.
I
g. 1.3
drill
1/2"
hole
I
I
I
I
1
2
3
4
5
• Drywall must be 1/2" or thicker.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
WARNING
1c-1
1c-2
Level cover plate and mark the center of the four mounting holes. Drill four 1/2" holes through drywall.
NOTE: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes.
D
2.5"
(64mm)
1/2"
(12mm)