peerless-AV DS-C560-1X3 User manual

12015-06-30 #:009-9119-3 (2016-05-16)
ENG
DS-C560-1X3
46" - 60"
(117 - 152 cm) 500 lb (227 kg)
MAX

22015-06-30 #:009-9119-3 (2016-05-16)
This page intentionally left blank.

32015-06-30 #:009-9119-3 (2016-05-16)
Heavy
(13mm)
Do not begin to install product until you have read and understood the instructions and warnings contained in
this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
This product must be installed onto flat, hard, level surface to prevent tipping. The cart or stand is not affixed or
secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. Displays must
be removed before moving cart. Not recommended for use in areas with heavy traffic. This product is intended
for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Screws must
be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the
Maximum Load Capacity. Be careful not to pinch fingers when operating the mount. For support please call
customer care at 1-800-865-2112.
WARNING
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
Display center.
ENG
x3
Screws must get at
least three full turns
and fit snug.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG

42015-06-30 #:009-9119-3 (2016-05-16)
Parts List
Part #Description Qty
Acaster, 5" swivel 4 600-0026
Bcaster support 4 145-T1799
Ccover 6 145-T1809
Dbase support tube 2 145-T1812
Ebase support 8 560-T1261
Fleft adaptor bracket 3 146-1609
Gright adaptor bracket 3 146-1608
Hbase leg 2 145-T1767
Ihorizontal leg support 1 146-T1340
Jvertical leg support 2 145-T1777
Kextension 2 145-T1778
Lvertical support bracket 6 145-T1806
Mcross support 3 145-T1816
Ncomputer cover 1 145-T1930
Ocomputer shelf 1 145-T1931
Pextension adaptor 2 145-T1935
Qcord bracket 4 146-T1321
Rknurled knob 4 560-1160
SM8 x 16mm socket button screw 120 520-9527
TM8 square nut 40 530-1066
Ucover clip 24 590-0317
VM5 x 10mm type-f, socket pin screw 8 520-1164
Wbar nut 20 146-1319
Xnylon shoulder washer 12 590-2233
YM6 x 12mm socket pin screw 12 520-1050
Z1/4" power bit 1 560-0263
AA 5mm allen wrench 1 560-9640
BB 4mm allen wrench 1 560-9646
Parts (Before beginning, make sure you have all parts shown below).
H (2)
base leg
A (4)
caster B (4)
caster support C (6) cover D (2)
base support
tube
E (8)
base support
J (2)
vertical leg
support
L (6)
vertical support
bracket
K (2)
extension
I (1)
horizontal leg
support
G (3)
right adaptor
bracket
F (3)
left adaptor
bracket

52015-06-30 #:009-9119-3 (2016-05-16)
N (1)
computer cover
S (120)
M8 x 16mm T (40)
M8 square nut U (24)
cover clip
V (8)
M5 x 10mm Z (1)
1/4" power
bit
AA (1)
5mm allen
wrench
nylon shoulder
washer
X (12)M6 x 12mm Y (12)
4mm allen
wrench
BB (1)
O (1)
computer shelf
Q (4)
cord
bracket
R (4)
knurled
knob
bar nut
W (20)
P (2)
extension
adaptor
M (3)
cross support

62015-06-30 #:009-9119-3 (2016-05-16)
1-1
S (4)
A
B
S (2)
T (2)
Do not fully tighten hardware
SIDE VIEW
(5mm)
AA
x4
x4
1-2

72015-06-30 #:009-9119-3 (2016-05-16)
2
S (4)
S (4)
D
D
T (2)
T (2)
H
T (2)
T (2)
(5mm)
AA
x2

82015-06-30 #:009-9119-3 (2016-05-16)
3
TIGHTEN
CONNECTING
HARDWARE
FLUSH
EDGES
ENG
Casters must be flush to end of horizontal leg support.
ENG
4
W (2)
E
S (4)
SIDE VIEW
Do not fully tighten hardware
x8
x3

92015-06-30 #:009-9119-3 (2016-05-16)
5
J
TIGHTEN
CONNECTING
HARDWARE
6-1
S (4)
W (2)
P
x2 Do not fully tighten hardware
x2

10 2015-06-30 #:009-9119-3 (2016-05-16)
7TIGHTEN
CONNECTING
HARDWARE
H
6-2
K (2)
P (2)
TIGHTEN
CONNECTING
HARDWARE
LOCK WHEELS