peerless-AV DS-LEDM Series User manual

12020-08-10 #:146-9051-1
ENG
DS-LEDM Series

22020-08-10 #:146-9051-1
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
#
Skip to step.
ENG
Wear anti-static gloves.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
ENG - This product is designed to be installed on plywood walls, solid concrete or cinder block walls. Hardware
is included for plywood installation. This product is designed to be installed on at, unobstructed, vertical walls.
Do not install on curved or angled walls. Before installing make sure the supporting surface will support the
combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or
damage can occur and product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or
mechanical lifting equipment to safely lift and position equipment. This product is intended for indoor use only.
Use of this product outdoors could lead to product failure or personal injury. Be careful not to pinch ngers when
operating the mount. For support please call customer care at 1-800-865-2112.
WARNING
x3
Screws must get at
least three full turns
and t snug.
ENG

32020-08-10 #:146-9051-1
Tools Needed for Assembly.
ENG
5/32"
(4mm)
5/16"
(8mm)
3/8"
(10mm)

42020-08-10 #:146-9051-1
Parts (Before beginning, make sure you have all parts shown below).
ENG
Parts List
Description Qty
Awall plate 1
Bbobbin 4
C#14-10 x 1.75" wood screw 4
Dbobbin screw 4
EM5 x 8mm philips screw 4
Fcombination tool 1
A (1)
wall plate
B (4)
bobbin
C (4)
#14-10 x 1.75" wood screw
D (4)
bobbin screw
F (1)
combination tool
E (4)
M5 x 8mm

52020-08-10 #:146-9051-1
1-1
1-2
A
E (4)
Sold separately.
Vendidos por separado.
Vendu séparément.
Separat verkauft.
Apart verkocht.
Venduto a parte.
Prodává se samostatně.
Predáva sa samostatne.
Vendido em separado.
Ayrıca satılır.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR

62020-08-10 #:146-9051-1
1-3
1-4
Sold separately.
Vendidos por separado.
Vendu séparément.
Separat verkauft.
Apart verkocht.
Venduto a parte.
Prodává se samostatně.
Predáva sa samostatne.
Vendido em separado.
Ayrıca satılır.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
Sold separately.
Vendidos por separado.
Vendu séparément.
Separat verkauft.
Apart verkocht.
Venduto a parte.
Prodává se samostatně.
Predáva sa samostatne.
Vendido em separado.
Ayrıca satılır.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR

72020-08-10 #:146-9051-1
Plywood
ENG
3
3b
Concrete/Cinder block
ENG
3a
2
3 4-1

82020-08-10 #:146-9051-1
3a
3a-1
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
Level wall mount and mark mounting holes
on plywood (must be minimum Grade BC,
1/2" (13mm) thick).
ENG
3a-2
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)

92020-08-10 #:146-9051-1
3a-3
3a-4
C (2)
3/8"
(10mm)
1/4"
(6mm)

10 2020-08-10 #:146-9051-1
3a-5
Mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick).
ENG
3a-6
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)

11 2020-08-10 #:146-9051-1
3a-7
3a-8
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximaal 80 in. • lb (9 N.M.).
Massima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maksimum 80 in. • lb (9 N.M.).
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
3/8"
(10mm)
3/8"
(10mm)
Sold separately.
Vendidos por separado.
Vendu séparément.
Separat verkauft.
Apart verkocht.
Venduto a parte.
Prodává se samostatně.
Predáva sa samostatne.
Vendido em separado.
Ayrıca satılır.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
Remove.
quite.
retirez.
entfernen.
verwijderen.
rimuovere.
odstranit.
odstrániť.
remova.
çıkartın.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR

12 2020-08-10 #:146-9051-1
6a-1
3a-9
3/8"
(10mm)
C (4)
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximaal 80 in. • lb (9 N.M.).
Massima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maksimum 80 in. • lb (9 N.M.).
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
Optional: Add displays by following sequence
shown and referring to steps 3a-5 through 3a-7
to attach wall plate to supporting surface using
hardware specied. First refer back to step 1-1
through 1-2 to secure the additional wall plates
in order to mark then drill mounting holes into
supporting surface.
ENG
1
3
245

13 2020-08-10 #:146-9051-1
This page intentionally left blank.
ENG

14 2020-08-10 #:146-9051-1
3b
ENG - When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi. When installing Peerless wall mounts on a cinder block wall, the cinder blocks
must meet ASTM C-90 specications and have a minimum nominal width of 8". Do not drill into mortar joints! Be
sure to mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block. It is suggested
that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking
out the back of the hole when entering a void or cavity. Never attach concrete expansion anchors to concrete or
cinder block covered with plaster, drywall or other nishing material.
WARNING
3b-1
Level wallplate. Mark mounting holes.
ENG
3b-2
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
5/16"
(8mm)
2.5"
(64mm)
5/16"
(8mm)
Do not drill into mortar joints.
ENG

15 2020-08-10 #:146-9051-1
3b-3
Insert anchor ush to concrete.
Inserte el anclaje a ras con el concreto.
Insérez la cheville d’ancrage au ras du béton.
Setzen Sie den Dübel bündig mit dem Beton
abschließend ein.
Breng anker aan gelijk met beton.
Inserire il fermo a paro col calcestruzzo.
Přestrčte ukotvenia priamo do betónu.
Prestrčte ukotvenia priamo do betónu.
Introduza a bucha encastrada no betão.
Tespit demirini betona takın.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
3b-4
C (2)
3/8"
(10mm)
1/4"
(6mm)
Sold separately; ACC234.
Vendidos por separado; ACC234.
Vendu séparément; ACC234.
Separat verkauft; ACC234.
Apart verkocht; ACC234.
Venduto a parte; ACC234.
Prodává se samostatně; ACC234.
Predáva sa samostatne; ACC234.
Vendido em separado; ACC234.
Ayrıca satılır; ACC234.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR

16 2020-08-10 #:146-9051-1
3b-5
3b-6
Mark mounting holes.
ENG

17 2020-08-10 #:146-9051-1
3b-7
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
5/16"
(8mm)
2.5"
(64mm)
5/16"
(8mm)
Do not drill into mortar joints.
ENG
3b-8
Insert anchor ush to concrete.
Inserte el anclaje a ras con el concreto.
Insérez la cheville d’ancrage au ras du béton.
Setzen Sie den Dübel bündig mit dem Beton
abschließend ein.
Breng anker aan gelijk met beton.
Inserire il fermo a paro col calcestruzzo.
Přestrčte ukotvenia priamo do betónu.
Prestrčte ukotvenia priamo do betónu.
Introduza a bucha encastrada no betão.
Tespit demirini betona takın.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
Sold separately; ACC234.
Vendidos por separado; ACC234.
Vendu séparément; ACC234.
Separat verkauft; ACC234.
Apart verkocht; ACC234.
Venduto a parte; ACC234.
Prodává se samostatně; ACC234.
Predáva sa samostatne; ACC234.
Vendido em separado; ACC234.
Ayrıca satılır; ACC234.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR

18 2020-08-10 #:146-9051-1
3b-9
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximaal 80 in. • lb (9 N.M.).
Massima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maksimum 80 in. • lb (9 N.M.).
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
3/8"
(10mm)
Sold separately.
Vendidos por separado.
Vendu séparément.
Separat verkauft.
Apart verkocht.
Venduto a parte.
Prodává se samostatně.
Predáva sa samostatne.
Vendido em separado.
Ayrıca satılır.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
3b-10
3/8"
(10mm)
Remove.
quite.
retirez.
entfernen.
verwijderen.
rimuovere.
odstranit.
odstrániť.
remova.
çıkartın.
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR

19 2020-08-10 #:146-9051-1
3b-11
3/8"
(10mm)
6a-1
C (4)
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximaal 80 in. • lb (9 N.M.).
Massima 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Maximum 80 in. • lb (9 N.M.).
Máxima 80 in. • lb (9 N.M.).
Maksimum 80 in. • lb (9 N.M.).
ENG
ESP
FRN
DEU
NEL
ITL
ČEŠ
SLK
POR
TÜR
ENG
1
3
245
Optional: Add displays by following sequence
shown and referring to steps 3b-6 through 3b-9
to attach wall plate to supporting surface using
hardware specied. First refer back to step 1-1
through 1-2 to secure the additional wall plates
in order to mark then drill mounting holes into
supporting surface.

20 2020-08-10 #:146-9051-1
This page intentionally left blank.
ENG