peerless-AV DS-LEDFLAAF-3X3 User manual

12019-11-15 #:146-9040-4 (2020-02-18)
ENG
DS-LEDFLAAF-3X3

22019-11-15 #:146-9040-4 (2020-02-18)
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.
Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
#
Skip to step.
ENG
Wear anti-static gloves.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3

32019-11-15 #:146-9040-4 (2020-02-18)
Parts (Before beginning, make sure you have all parts shown below).
ENG
Parts List
Part #Description Qty
Aconnector plate 19 096-1714
Bhorizontal spacer 2 096-1718
Cvertical spacer 3 096-1715
Dside trim 2 096-1716
Eharness holder 4 096-1731
Fupper left wall plate assembly 1 096-1719
Gupper right wall plate assembly 1 096-1720
Hlower left wall plate assembly 1 096-1721
Ilower right wall plate assembly 1 096-1722
Jvertical column double 2 096-1772
Kvertical column single 2 096-1771
LM5 x 8mm 38 520-1144
MM5 x 6mm 4 520-9504
Nwood screw 18 521-1688
OM4 x 75mm 36 521-1060
P4mm allen wrench 1 560-9646
Q3mm t-handle allen wrench 1 560-0435
N (18)
wood screw O (36) M4 x 75mm
E (4)
harness holder
A (19)
connector plate
G (1)
I (1)
upper right wall plate assembly
lower right wall plate assembly
F (1)
upper left wall plate assembly
H (1)
lower left wall plate assembly
L (38)
M5 x 8mm M (4) M5 x 6mm
P (1)
4mm allen wrench
Q (1)
3mm allen wrench
two-tip T-handle

42019-11-15 #:146-9040-4 (2020-02-18)
J (2)
vertical column
double
D (2)
side trim
C (3)
vertical spacer
B (2)
horizontal spacer K (2)
vertical column
single

52019-11-15 #:146-9040-4 (2020-02-18)
34.11"
(866mm)
33.80"
(858mm)
58.44"
(1484mm)
60.00"
(1524mm)
103.67"
(2633mm)
114.61"
(2911mm)
.21"
(5mm)
LED Trim
(not included)
3.04"
(77mm)
1
K
Dimensions are for reference only. Use spacers
provided.
ENG

62019-11-15 #:146-9040-4 (2020-02-18)
2-1
Use extrusion connectors to connect top horizontal
wall plate assemblies.
ENG
A (4)
F
G
L (8)
2-2
Use extrusion connectors to connect bottom wall
plate assemblies.
ENG
L (6)
A (3)
H
I
Q
Q

72019-11-15 #:146-9040-4 (2020-02-18)
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
3
3-1
Use a laser level to keep mounting holes
level.
ENG

82019-11-15 #:146-9040-4 (2020-02-18)
3-2
Level wall plates and mark mounting holes
on plywood (must be minimum Grade BC,
1/2" (13mm) thick.)
ENG
F
G

92019-11-15 #:146-9040-4 (2020-02-18)
N (6)
3-4 Level wall plates. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
ENG
3-3
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
ENG
5/32"
(4mm)
2.5"
(64mm)
5/32"
(4mm)

10 2019-11-15 #:146-9040-4 (2020-02-18)

ENG
3-5

horizontal extrusion.
ENG
3/8"
(10mm)
F
N
C (2)
N (4)