peerless-AV DS-S555-3X3 User manual

12014-07-30 #:009-9089-5 (2018-03-12)
ENG
DS-S555-3X3
46" - 55"
(117 - 140 cm)
900 lb
(409 kg)
MAX

22014-07-30 #:009-9089-5 (2018-03-12)
This page intentionally left blank.

32014-07-30 #:009-9089-5 (2018-03-12)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
Display center.
ENG
3/8"
(10mm)
3/8"
(10mm)
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product must be installed onto at, hard, level surface to prevent tipping. Use with heavier
displays may result in instability causing tip over resulting in death or serious injury. Displays must be removed
before moving cart. Not recommended for use in areas with heavy trafc. This product is intended for indoor use
only. Use of this product outdoors could lead to product failure or personal injury. Screws must be tightly secured.
Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load
Capacity. Be careful not to pinch ngers when operating the mount. Death or serious injury may occur when
children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may
encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child. Relocating
audio and/or video equipment to furniture not specically designed to support audio and/or video equipment may
result in death or serious injury due to the furnishing collapsing or over turning onto a child. For support please
call customer care at 1-800-865-2112.
WARNING

42014-07-30 #:009-9089-5 (2018-03-12)
Parts (Before beginning, make sure you have all parts shown below).
Parts List
Part # Description Qty
Apedestal 2 146-T1132
Bcolumn 2 146-T1131
Cextension 2 145-T1778
Dcover 2 145-T1809
Eside support bracket 4 145-T1807
Fvertical support bracket 6 145-T1806
Gleft adaptor bracket 9 146-1609
Hright adaptor bracket 9 146-1608
Icomputer cover 1 145-T1930
Jcomputer shelf 1 145-T1931
Kdual cross support 3 146-T1905
Lextension adaptor 2 145-T1935
Mcord bracket 4 145-T1321
Nknurled knob 4 560-1160
Ocross support 3 146-T1904
Pplate connections 6 145-T1821
QM8 x 16mm socket button screw 112 520-9527
RM8 square nut 50 530-1066
Scover clip 8 590-0317
TM5 x 10mm type-F, socket pin screw 20 520-1164
Ubar nut 4 146-1319
V1/4" power bit 1 560-0263
W5mm allen wrench 1 560-9640
Xnylon shoulder washer 36 590-2233
YM6 x 12mm socket pin screw 36 520-1050
Z4mm allen wrench 1 560-9646
AA M6 x 35mm screw 8 520-0717
BB rawl bolt #6913 8 5M9-381-H03
CC M8 x 20mm screw 6 520-1754
D (2)
cover
B (2)
column
F (6)
vertical support
bracket
E (4)
side support
bracket
C (2)
extension
A (2)
pedestal H (9)
right adaptor
bracket
G (9)
left adaptor
bracket

52014-07-30 #:009-9089-5 (2018-03-12)
O (3)
cross support
Z (1)
4mm allen
wrench
I (1)
computer cover
Q (112)
M8 x 16mm
R (50)
M8 square
nut
S (8)
cover clip T (20) M5 x 10mm
V (1)
1/4" power
bit
W (1)
5mm allen
wrench
X (36)
nylon shoulder
washer
Y (36)
M6 x 12mm
P (6)
plate
connections
L (2)
extension
adaptor
J (1)
computer shelf
rawl bolt
BB (8)
M6 x 35mm
AA (8)
K (3)
dual cross
support
M (4)
cord
bracket
N (4)
knurled
knob
bar nut
U (4)
CC (6)
M8 x 20mm

62014-07-30 #:009-9089-5 (2018-03-12)
1
2
x2
x2
AA (4)
A
B
TOP VIEW
L
Q (4)
U (2)
Do not fully tighten hardware
W

72014-07-30 #:009-9089-5 (2018-03-12)
3
x2
TIGHTEN
CONNECTING
HARDWARE
C
B
W

82014-07-30 #:009-9089-5 (2018-03-12)
1/8"
(3mm) 1/8"
(3mm)
TIGHTEN
CONNECTING
HARDWARE
DISPLAY HEIGHT
DISPLAY HEIGHT
Q (6)
R (4)
F
4
5
x6
x2
W
W
F (3)

92014-07-30 #:009-9089-5 (2018-03-12)
TIGHTEN
CONNECTING
HARDWARE
MN
S (4)
Dx2
6-2
M (2)
N (2)
6-1
x2

10 2014-07-30 #:009-9089-5 (2018-03-12)
7
ENG - When installing Peerless mounts on a concrete oor, the oor must be at least 8" thick with a minimum
compressive strength of 2000 psi. Never attach concrete expansion anchors to concrete covered with plaster,
drywall, or other nishing material.
WARNING
FRN - Lors de l’installation de supports de plafond Peerless sur un plafond en béton, celui-ci doit avoir au moins
8 po (20 cm) d'épaisseur et une résistance à la compression d'au moins 2 000 psi. Ne xez jamais des chevilles
à expansion pour béton à du béton recouvert d’une couche de plâtre, d’une cloison sèche ou de tout autre
matériau de nition.
ADVERTISSEMENT
ESP - Cuando vaya a instalar soportes de techo de Peerless en techos de concreto, los techos tienen que
tener, por lo menos, 8" de grosor con una resistencia a la compresión de 2000 psi como mínimo. Nunca je los
anclajes de expansión para concreto a supercies de concreto recubiertas con yeso, yeso-cartón u otro material
de acabado.
ADVERTENCIA
DEU - Werden Peerless-Deckenhalter an einer Betondecke angebracht, so muss deren Dicke mindestens 203
mm (8 Zoll) und ihre Druckfestigkeit mindestens 13,8 N/mm2 (2000 psi) betragen. Betonspreizdübel dürfen
auf keinen Fall an Beton befestigt werden, der mit Verputz, Trockenwand- oder anderem Deckschichtmaterial
bedeckt ist.
ACHTUNG
WAARSCHUWING
NEL - Als de Peerless-plafondbevestiging op een betonnen plafond wordt geïnstalleerd, moet dit plafond een
dikte van ten minste 20 cm hebben en een druksterkte van ten minste 2000 psi. Gebruik nooit expansie-ankers
voor beton bij installatie op een betonnen plafond bedekt met gips, gipsplaat of ander afwerkingsmateriaal.
ITL - In sede d’installazione dei sostegni Peerless su un softto in calcestruzzo solido, il softto deve avere
uno spessore minimo di 20 cm, con una resistenza alla compressione di almeno 2000 psi (140 kg/cm2). Non
attaccare mai ancoranti a espansione per calcestruzzo su calcestruzzo ricoperto con intonaco, cartongesso o
altro materiale di nitura.
AVVERTENZA
ČEŠ - Při instalaci stropních držáků Peerless na betonový strop musí být tento trop hrubý minimálně 20 cm s
minimální pevností v tlaku 2000 psi. Expanzní kotvy do betonu nikdy nepřipojujte do betonu pokrytého omítkou,
sádrokartonem nebo jiným dokončovacím materiálem.
VÝSTRAHA
TÜR - Peerless tavan kaidelerini beton duvara monte ettiğinizde, tavan en azından 2000 psi asgari basınç
dayanımına sahip olmalı ve kalınlığı da en azından 8" olmalıdır. Beton dübelleri hiç bir zaman alçı, alçıpan veya
başka bir bitirme materyali ile kaplı betona takmayınız.
UYARI
AVISO
POR - Ao instalar os suportes para o teto Peerless em tetos de betão, o teto deve ter, no mínimo, 203 mm de
espessura e uma força de compressão mínima de 2000 psi. Nunca instale âncoras de expansão para betão em
superfícies cobertas com estuque, gesso ou outros materiais de acabamento.
SLK - Pri montáži stropných držiakov Peerless na betónový strop musí mať tento strop hrúbku minimálne 20 cm
s minimálnou tlakovou pevnosťou 2000 psi. Expanzné kotvy do betónu nikdy nenasadzujte do betónu pokrytého
omietkou, sadrokartónom či iným nalizačným materiálom.
VÝSTRAHA

11 2014-07-30 #:009-9089-5 (2018-03-12)
BB (8)
Tighten.
ENG
4
3"
(76mm)
3/8"
(10mm)
7-1
Align base. Mark mounting holes.
ENG
7-2
Drill mounting holes into
supporting surface
(3" (76mm) minimum
depth required).
ENG
3/8"
(10mm)
7-3
Align base. Install using concrete anchors
provided.
ENG
3/8"
(10mm)
55.00"
(1397mm)
55.00"
(1397mm)
ENG Maximum 35 ft • lb (47 N.M.).

12 2014-07-30 #:009-9089-5 (2018-03-12)
8-1
8-2
8-3
K
O
Q (4)
Q (4)
R (4)
R (2)
CC (2)
P (2)
x3
x3
x3
W
W
W

13 2014-07-30 #:009-9089-5 (2018-03-12)
9-1
TIGHTEN
CONNECTING
HARDWARE (X4)
Cross supports must center on columns.
W
Tighten.
ENG Tighten. ENG

14 2014-07-30 #:009-9089-5 (2018-03-12)
9-2
TIGHTEN
CONNECTING
HARDWARE (X4)
Cross supports must center on colmuns.
W
Tighten.
ENG Tighten. ENG

15 2014-07-30 #:009-9089-5 (2018-03-12)
TIGHTEN
CONNECTING
HARDWARE (X4)
Cross supports must center on columns.
9-3 W
Tighten.
ENG Tighten. ENG

16 2014-07-30 #:009-9089-5 (2018-03-12)
Side support brackets must center on cross supports.
10
E
E (4)
Q (2)
Q (8)
R (2)
R (8)
W

17 2014-07-30 #:009-9089-5 (2018-03-12)
X
X
11-1
H
G
11-2
Center adaptor brackets
vertically on back of screen.
ENG
H
G
x3
X Y Q
OR
Z
x9
x9 W

18 2014-07-30 #:009-9089-5 (2018-03-12)
12-1
12-2
Must hang displays on bottom row rst. Secure pin
in "locked" position.
Must hang displays on middle row second. Secure
pin in "locked" position.
"LOCKED"
POSITION
"LOCKED"
POSITION

19 2014-07-30 #:009-9089-5 (2018-03-12)
12-3
Must hang displays on top row last. Secure pin
in "locked" position.
"LOCKED"
POSITION
12-4
Optional: Insert M5 x 10mm type-F socket pin screws
(T) to lock latches.
T
"LOCKED"
POSITION
Z
x18

20 2014-07-30 #:009-9089-5 (2018-03-12)
13
Display adjustment
IN
TILT BACKWARD
OUT
TILT RIGHT
TILT FORWARD
TILT LEFT
SIDE
SIDE
SIDE
TOP
SIDE
TOP
UP DOWN
ROTATE LEFT ROTATE RIGHT