peerless-AV KIP749-S User manual

12015-04-28 #:150-9054-3 (2017-07-12)
ENG

22015-04-28 #:150-9054-3 (2017-07-12)
Symbols
ENG
WARNING
ENG x3
Screws must get at least three
full turns and t snug.
ENG
Do not overtighten screws.
ENG
ENG - Do not begin to install product until you have read and understood the instructions and warnings contained
in this user guide. This product is designed to be installed on wood stud walls. Hardware is included for wood
stud installation. Before installing make sure the supporting surface will support the combined load of the
equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur
and product may fail. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product is intended for indoor use only. Use of this product outdoors could lead to product failure
or personal injury. To reduce the risk of electric shock or re, do not expose product to water or moisture. Be sure
power cord is routed so that it will not be tripped on, stepped on, or pinched by heavy items. Avoid overloading
electrical outlets or extension cords. Always disconnect the power cord from the power outlet when installing,
servicing, or not using the product for an extended period of time. Do not block ventilation slots or fan exhaust
on product. Blocking airow could damage product. Arrange product to allow air to ow freely around product.
Keep product away from direct sunlight or any source of heat. For support please call 800-4-SIGNAGE.
WARNING

32015-04-28 #:150-9054-3 (2017-07-12)
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
+1/2
4
3

42015-04-28 #:150-9054-3 (2017-07-12)
Parts List KIP740
KIP740-S
Part #
KIP742
KIP742-S
Part #
KIP743
KIP743-S
Part#
KIP746
KIP746-S
Part #
KIP747
KIP747-S
Part #Description Qty
Aback assembly 1150-T1693 150-T1694 150-T1694 150-T1690 150-T1691
BM5 x 12mm pan phl screw 4 520-1027 520-1027 520-1027 520-1027 520-1027
CM5 X 25mm pan phl screw 4 520-9543 520-9543 520-9543 520-9543 520-9543
DM6 x 12mm pan phl screw 4 520-1128 520-1128 520-1128 520-1128 520-1128
EM6 x 25mm pan phl screw 4 520-1208 520-1208 520-1208 520-1208 520-1208
FM8 x 12mm pan phl screw 4 520-9571 520-9571 520-9571 520-9571 520-9571
GM8 x 25mm pan phl screw 4 520-1031 520-1031 520-1031 520-1031 520-1031
HM5/M4/M6 multi washer 4 580-1398 580-1398 580-1398 580-1398 580-1398
I1/4"spacer 4 540-1059 540-1059 540-1059 540-1059 540-1059
JM5 x 20mm skt screw 2520-1065 520-1065 520-1065 520-1065 520-1065
K4mm allen wrench 1560-9646 560-9646 560-9646 560-9646 560-9646
Lfront cover BLK
front cover SLV
1150-P1596P
150-4596P
150-P1599P
150-4599P
151-P1610
151-4610
150-P1593P
150-4593P
150-P1594P
150-4594P
M#14 x 2.5" wood screw 4 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03
Nadaptor bracket 2150-T1689 150-T1689 150-T1689 150-T1689 150-T1689
Opower strip 1 600-0370 600-0370 600-0370 600-0370 600-0370
Pcable tie 6 560-1756 560-1756 560-1756 560-1756 560-1756
Qconcrete anchor (not used) 4 590-0320 590-0320 590-0320 590-0320 590-0320
Parts List KIP748
KIP748-S
Part #
KIP749
KIP749-S
Part #
KIP755
KIP755-S
Part#Description Qty
Aback assembly 1150-T1692 150-T1695 150-T1695
BM5 x 12mm pan phl screw 4 520-1027 520-1027 520-1027
CM5 X 25mm pan phl screw 4 520-9543 520-9543 520-9543
DM6 x 12mm pan phl screw 4 520-1128 520-1128 520-1128
EM6 x 25mm pan phl screw 4 520-1208 520-1208 520-1208
FM8 x 12mm pan phl screw 4 520-9571 520-9571 520-9571
GM8 x 25mm pan phl screw 4 520-1031 520-1031 520-1031
HM5/M4/M6 multi washer 4 580-1398 580-1398 580-1398
I1/4"spacer 4 540-1059 540-1059 540-1059
JM5 x 20mm skt screw 2520-1065 520-1065 520-1065
K4mm allen wrench 1560-9646 560-9646 560-9646
Lfront cover BLK
front cover SLV
1150-P1595P
150-4595P
151-P1818
151-4818
150-P1600P
150-4600P
M#14 x 2.5" wood screw 4 5S1-015-C03 5S1-015-C03 5S1-015-C03
Nadaptor bracket 2150-T1689 150-T1689 150-T1689
Opower strip 1 600-0370 600-0370 600-0370
Pcable tie 6 560-1756 560-1756 560-1756
Qconcrete anchor (not used) 4 590-0320 590-0320 590-0320
Parts (Before beginning, make sure you have all parts shown below).
ENG

52015-04-28 #:150-9054-3 (2017-07-12)
A (1)
L (1)
back assembly
front cover
B (4)
M5 x 12 mm
C (4)
M5 x 25 mm
D (4)
M6 x 12 mm
E (4)
M6 x 25 mm
M5/M4/M6 washer
H (4)
M8 x 12 mm
F (4)
M8 x 25 mm
G (4)
spacer
I (4)
K (1)
J (2)
allen
wrench
M5 x 20mm
M (4)
#14 x 2.5" wood screw
Q (4)
concrete anchor
N (2)
adaptor bracket
O (1)
power strip cable tie
P (6)

62015-04-28 #:150-9054-3 (2017-07-12)
xx"
yy"
1-2
KIP740, KIP742, KIP743
KIP746, KIP747, KIP748
KIP749, KIP755
XX = 27.25", YY = 43.5"
XX = 30.25", YY = 48.25"
XX = 33.75", YY = 55.75"
1
1-1
ENG - When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that
the wood studs are a minimum of 2" x 4" nominal size. Do not install over gypsum board thicker than 5/8".
WARNING
Use stud nder to locate and
mark stud center lines.
ENG

72015-04-28 #:150-9054-3 (2017-07-12)
1-5
A
1-4
1-3
5/32"
(4mm)
2.5"
(64mm)
5/32"
(4mm)
Drill mounting holes into supporting surface (2.5" (64mm) minumum depth required).
ENG
Level wallplate. Mark mounting holes on stud.
ENG
A

82015-04-28 #:150-9054-3 (2017-07-12)
1-6
Level wallplate. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG M (4)
A

92015-04-28 #:150-9054-3 (2017-07-12)
2
3
B (4)
I (4)
H (4)
C (4) D (4) H (4)
G (4)
I (4)
I (4)
H (4)
F (4)
X
X
ENG Use of spacers is optional.
x3
Center adapter brackets vertically on back of screen.
ENG
E (4)
H (4)
N (2)

10 2015-04-28 #:150-9054-3 (2017-07-12)
4
5
Note: Mounting arm swings out
to access adapter brackets and
behind display.
ENG