PEERLESS LC SERIES Instruction manual

LC/LCE
Gas/Off Boilers -Steam
Installation,
Operation
Maintenance
Manual
PEERLESS °
CAST IRON BOILERS

22 Sizes 4-24 Sections 4.75 to 32.5 GPH Input Up to 83.7% Combustion Efficiency
Forced Draft Venting
•Only Requires a Three Foot Vent Above the Roof
High Efficiency Power Burners
•Choice ofBeckett, Carlin, Gordon-Piatt, Power Flame or Webster
Integral Cast Iron Flue Collector
•Adds Durability and Reduces Operating Noise
Rear Flue Outlet on LC, Top Flue Outlet on LCE
• Provides Optimum Flue Gas Travel for Increased Efficiency
•Includes Locking Damper
Wet Base Section Design with Tubular Heat Exchanger
•Provides Additional Heating Surface for Optimum Heat Transfer
Safety Controls
•Probe or Float Type Low Water Cut OffAvailable
Tankless Coils
• For Domestic Hot Water Production on Hot Water Boilers
Unique Flex-Seal Flow Port Gaskets
• Injection Molded for Superior Performance and Flexibility
•Assures a Water Tight Seal Between Sections
Individual Draw Rods
•For Ease of Assembly
Insulated Enameled Steel Jacket
•Reduces Bo_er Heat Loss
• Honeywell Operating Controls
•Manual Reset High Limit Control
• LWCO on Packaged Boilers
• Tankless Coils
• Various Burner Opliol_s and Voltages
•FM and IRI Control Syslems
Peerless Boilers is pleased to qlTer one of the most comptz,h_,nsive wantruly programs irl the indttstl y. All Peerless commercial
cast i1oll boil_'rs irlclude a filll, one year it_atTatlty. A limitt_¢t, tell year tt!Cllwa_ll[j Oil lilt; ¢'(ISl ir_)tl ._('cIioIIs is provided.lbr (111 col_l
lTlul'ci¢l{ ]tol It!¢ll_'l CJlICI sleanl boilers. Fivt_ (lll(_ lell year ¢'.k'I¢'llc'l¢!¢l it;(lrl(ltl{i¢'s Oil 11(111.% (llld !¢llx)l ¢1r€" iiott_ available,. /)l¢'(lst' ¢'¢._tt
still Pt'erlt,ss [Joilera.lot complete tv(trratlly it{lbrmaliotl,
Peerless Boilers •610-367-2153 * www.peerless-heater.com
FA6 LC R3 i3031MI
Pr_n_o_Jirl U S A

pr=-r=-RLESS o
CAST IRON BOILERS
Series LC/LCE
Large Commercial Boilers
• Packaged, Assembled Block or
Individual Sections
oForced Draft Venting
Power Burners
•Oil, Gas, Gas/Oil
QSteam or Hot Water Boilers
Optional Tankless Coils
Series LC
Series LCE
Net I=B=R Ratings 4 Efficiency 5Water Content
Oil Gas
.... I I m
Model Output Boiler Oil Input Gas Input l Steam Steam3 Water 2Comb. Therm. Comb. Therm.
Number MBH H,P. GPH 1MBH Sq. Ft. MBH MBH % % % % Steam Water
LC-O4 547 16.3 4.75 686 1,708 410 476 83.7 82.2 81.2 79.8 40.57 50,65 mm
,0.05,_,9 19.4 5.60 80_ 2.029,7 56, _.7 62.561.290._47.29 69.0,m
LC-05 707 21.1 6.10 881 2,208 530 615 83.7 82.8 81.2 803 47.29 59.05 II
LC-06 866 25.9 7.59 1,077 2,713 651 755 83.7 83,1 81,1 80.8 54.01 67.45 I
LC-07 1029 30.7 8.80 1,273 3,217 772 895 83.6 83.3 61.1 806 60.79 75.55 I
LC-08 1189 35.5 10.20 1,469 3,717 892 1,034 83.6 835 61.1 81.0 67.46 84.25 I
LC-09 1350 40.3 11.60 1,864 4,250 1,020 1,174 83,6 83.6 811 81.1 74.17 91.65 I
LC-10 1511 45.1 12.80 1,860 4,804 1,153 1,314 83.6 83.7 81.1 81.2 80.88 101,05 I
LC-11 1872 48.9 14.26 2,056 5,367 1,288 1,454 63.6 83.8 811 81.3 87,61 109,45 I
LC-12 1832 54,7 15.60 2,252 5,917 1,420 1,593 83.6 83.9 811 814 94.33 117,65 I
LCE-13 1966 58.7 17,00 2,464 6,358 1,526 1,710 83,5 822 61.0 79,8 101.05 126,25 I
LCE-14 2128 83.5 18.40 2,657 6,875 1,650 1,848 83.5 625 810 80.0 107.77 134,65 •
LCE-15 2284 66,2 19.80 2,850 7,388 1,773 1,986 83.5 826 510 80.2 114.49 143,05 I
LCE-16 2444 73,0 21.00 3,043 7,908 1,896 2,125 83.5 82.8 610 80.3 121.21 151.45 I
LCE-17 2603 77.8 22.50 3,236 8,421 2,021 2,283 83.5 629 81.0 80.4 t 27.93 15985 I
LCE-18 2763 82.5 24.00 3,429 6,938 2,145 2,403 83.5 83.1 810 80.6 134.65 168.25 I
LCE-19 2922 87.3 2500 3,622 9,454 2,289 2,541 83,5 83.2 81.0 80.7 141.37 176.65 I
LCE-80 3082 92.1 2650 3,815 9,971 2,393 2,680 83.5 833 810 806 148,09 18505 I
LCE-21 3256 97.3 2800 4,027 10,533 2,528 2,831 83.6 63 3 81 1 809 15481 19345 I
LCE-22 3430 102.5 29.80 4,239 11,096 2,663 2,983 83.6 834 8t 1 808 161.53 20185 •
LCE-23 3604 107.7 31.00 4,451 11,658 2,798 3,134 83.7 835 812 81.0 168.25 210.25 •
LCE-24 3777 1128 32,50 4,663 12,217 2,932 3,284 83.7 835 812 81.0 174.97 218.65 I
1 Burner input based on No. 2 fuel oit with a beating value of 140,000 Btu per garlon
2 Net I_B-R water ratings based on allowance of 1.15.
3 Net I=B-R steam ratings based on an allowance for LC-04 to LC-05 1.333, LC-09 1.323, LC-10-1.310, LC-11=1.298, LC-12 1.290, LCE-13 to LCE-24=1.288.
4 Consult factory before selecting a boiler for installation having unusual piping and pickup requirements, such as intermitlent system operation, extensive piping systems, etc
5 Combustion and thermal efficiency determined in accordance with The Hydronics Institute's Testing and Rating Standard for Heating Boilers

SERIES LC SPECIFICATIONS
F_[o]llll=l_ I_]]_r_l_J_.-][o_[,."]F_1Lqi]If.'1_ ][e[_ _[,,.'!1
Boiler
Model
Number
LC-04
LC-05R
LC-05
LC-06
LC-07
LC-08
LC-09
LC-10
LC-11
LC-12
Width
"A"
37"
37"
37"
37"
37"
37"
37"
37"
37"
37"
Jacket
Length
"B"
25_%#'
31"
31"
36¼s"
41W'
46%6"
513/."
56%#'
61½"
66%s"
Top to Floor
63"
63"
63"
63"
63"
63"
63"
63"
63"
63"
Left of Floor to
C/L of
Flue
"E"
54W'
54W'
54W'
541/8 `'
54W'
54W'
541/8 ''
54W'
54W'
54W'
Flue
Size
"F"
9"
9"
9"
10"
10"
10"
12"
12"
12"
12"
Distance Between Tappings*
Jacket to
C/L of
Flue
18W'
181/4 "
18V4"
18_ ,,
18V4"
18V4"
181/4"
18V4"
18W'
18_A,,
liG_l
16_/_"
21_A#'
219/_6"
265/8"
31"/_e"
36_3/_#'
417/_"
46_5/_e"
52"
57W'
"GI"
15_¾6"
20_%6"
20_¾8"
26"
26"
Apply Prefix "O" for oil--"G" for gas--"GO" for gas-oil *Dimensions are approximate
The manufacturer should be consulted before selecting a boiler for installations having unusual piping and pickup requirements, such as intermittent system operation,
extensive piping, etc. For forced hot water heating systems where the boiler and all the piping are within the area to be heated, the boiler may be selected on the
basis of its Gross Output.

SERIES LC/LCE SPECIFICATIONS
STEAM PIPING
Pipe the return line to a Hartford Loop, with the return nipple located from 2 to 4 inches below the normal water line.
Model
Number
LC-04
LC-O5R
LC-05
LC-06
LC-07
LC-08
LC-09
LC-IO
LC-11
LC-12
Riser
14"
2--3"
2--3"
24"
24"
24"
24"
24"
24"
1--3"
2_"
Minimum
Header
Size Equalizer
4" 2"
5" 2"
5" 2"
5" 2"
5" 21/2"
6" 21/2"
6" 21/2'
6" 21/2"
6" 3"
6. 3.
14"
Model
Number
LCE-13
LCE-14
LCE-15
LCE-16
LCE-17
LCE-18
LCE-19
LCE-20
LCE-21
LCE-22
LCE-23
Riser
2_4", 1_3"
2_", 2--3"
2_4", 2--3"
2---4", 2--3"
24", _"
2_", 3_3"
24", 3--3"
24", 4_3"
24", 4---3"
2_4", 4---3"
24", 4--3"
Minimum
Header
Size
6"
8"
8"
8"
8"
8"
6"
8"
8"
8"
6"
6"
Equalizer
3"
3"
3'=
3"
4"
4"
4"
4"
4"
4"
4"
4"
WATER PIPING
Size the supply and return headers to meet the system flow requirement.
Model
Number
LC-64, 85R, 65
LC-06 and LC-07
LC-68 and LC-09
LCqO thru LCE-16
LCE-17 thru LCE*20
LCE-21 thru LCE*24
Supply Return
1--2W' 1--2Vz"
1--3" 1--3"
2--3" 2--3"
2--4" 2--3"
2_" 2--3"
24" 3-3"
Minimum
Header
Size
21/2,,
3"
3"
4"
6"
5"

SERIES LC/LCE SPECIFICATIONS
613/4"
-- --_ 345,46,,
Large, Integral
Cast Iron Flue Collector
Unique Flex-Seal Gaskets
-- Tubular Heat Exchanger
-- Large Combustion Chamber
Individual Draw Rods
HEATER
LOCATION
#1
FRONT
HEATER
LOCATION
#2
I
_ Series LCE Includes
E _i Cast lron Rear Cover Plate
_:m - _ LOCATION
Heater No.
X-1020
Boiler Location**
Model mTw
Number GPM Stea ater
LC-04 5.5 1 2
LC-O5R 5.62 t 2
LC-05 5.75 1 2
LC-06 6.25 1 2
LC-07 6.5 1 2
LC-08 7.0 1 2
LC-09 7.25 1 2
LC-10 7.5 1 2
LC-11 8.0 1 2
LC-12
LCE-13
LCE-14
LCE-15
LCE-16
LCE-17
LCE-18
LCE-19
LCE-20
LCE-21
LCE-22
LCE-23
LCE-24
Heater No. Heater No. Two Heaters Two Heaters
X-1021 X-1022 No. Xo1020 No. X-1021
Location** Location** Location** Location**
GPM SteamlWater GPM Steam Water GPM Steam Water GPM ,Steam Water
8.0 -- 1&2
Two Heaters
No. X-1022
Location**
GPM Steam Wate!
13.00 1 2 20.0 1 2 1 & 2
" Water heater rahngs are based on intermittent deman_O ° P to 140° F Rise with 200 ° Fboiler water
** Water beater locations may be found on the drawing above.
When two (2) tankless water heaters are used in asteam boiler, a special rear section is furnished at no extra charg_when ordered with boiler,
Caution: Water mixing valve should always be installed in the hot water supply to prevent injury.
6.5 129.0 -- 1 & 2 9,5 -- 1&2
7.0 1 2 10.0 -- 1&2 10.5 -- 1&2
7.75 1 2 12.0 -- 1&2 13.0 -- 1&2
8.5 1 2 13.0 1 2 13.0 -- 1&2 15.5 -- 1&2 15.5 -- 1&2
9.25 1 2 13.75 1 2 14.0 -- 1 & 2 17.5 -- 1 & 2 18.0 -- 1 & 2
10.0 1 2 14.5 1 2 14.5 1&3 1&2 20.0 -- 1&2 20.0 -- 1&2
10.75 1 2 15.5 1 2 15,9 1&3 1&2 21.5 1&3 1&2 22.5 -- 1&2
11.56 1 2 16.5 1 2 16.0 1&3 1&2 23.5 1&3 1&2 24.5 -- 1&2
12.25 1 2 17.5 1 2 ..... 24.5 1&3 1&2 27.0 -- 1&2
13,00 1 2 18.0 1 2 26,0 1&3 1&2 29.0 -- 1&2
13.00 1 2 18.75 12 ..... 26.0 1&3 1&2 31.5 -- 1&2
13.00 1 2 19.5 1 2 ..... 26.0 1&3 1&2 33.5 1&3 1&2
13.00 1 2 20.0 1 2 26.0 1&3 1&2 35.5 1&3 1&2
13.00 1 2 20.0 1 2 - IZI I __I-- 26.0 1&3 1&2 37.5 1&3 1&2
13.00 1 2 20,0 1 2 26.0 1&3 1&2 39.8 1&3 1&2
13.00 1 2 20.0 1 2 ..... 26.0 1&3 1&2 40.0 1&3 1&2
13.00 1 2 20.0 1 2 ..... 26.0 1&3 1&2 40.0 1&3 1&2
13.00 1 2 20.0 1 2 ..... 26.0 1&3 1&2 40.0 1&3 1&2
13.00 1 2 20.0 1 2 26.0 11&3 1&2 40.0 1&3 1&2
i
13.00 1 2 20.0 I2 -- 26.0 11&3 1&2 40:0 1&3 1&2
, -- ' -- 26.0 I 1&3 40.0 1&3 1&2

SERIES LCE SPECIFICATIONS
\Rear Flue
Cover
R
E
A
R
Cast Iron Block Assembly-Top Flue Outlet Butterfly Flue Damper (Series LCE)
Mounted Horizontally or Vertically
TOp
_l_ <D I
4_/,_" • .* G_ 4,_,_¢ 16'_1(_ 4"SupplyTappings
]- : _ (_) 3"RearReturnTapping
• I=.=._o _) 3"Side Returns
c"Re"r°b e 'ati°nF "
63" T_3"IntermediateSupply
"ii __, 4_/£ Tappings
37" @ lye Line M_ximum POWERFLAMEC=36"
Burner G CRDON &RATr R = _7 _
FRONT RIGHT SSDE REAR Lengths: WEBSTER J=31"
Note: Series LCE steam boiler pictured, Series LCE water boiler has, at most, two tapped intermediate sections.
Boiler
Model
Number
LCE-13
LCE-t4
LCE-15
LCE-16
LCE-17
LCE-18
LCE-19
LCE-20
LCE-21
LCE-22
LCE-23
LCE-24
Width
"A"
37"
37"
37"
37"
37"
37"
37"
3T'
37"
37"
37"
37"
Jacket Left of Front of
Jacket to Jacket to
Top to C/L of C/L of Flue
Length Floor Flue Flue Size
"B .... C.... D.... E.... F"
715/4" 63" 16" 20%" 14"
76_5/16" 63" 16" 20V2" 14"
81%" 63" 16" 20%" 14"
86_%6" 63" 16" 201/2" 14"
92Vs" 63" 16" 20V2" 14"
97_A6" 63" 16" 20V2" 16"
102W' 63" 16" 20'/2" 16"
1077/_s'' 63" 16" 20'/2" 16"
112W' 63" 16" 20%" 16"
1179/,6" 63" 16" 20%" 16"
122%" 63" 16" 20W' 16"
127_/_ " 63" 16" 201/2" 16"
Distance Between Tappings*
Water Steam
"G .... G1 .... G2 .... G1.... G2 .... G3 .... G4"
625/16" 363/16" -- 365/16" -- -- --
67V4" 41%" -- 201-%6" 20%6" -- --
72%6" 46%" -- 26" 20%6" -- --
777/_6' 517/_6" -- 26" 255/_6" -- --
82W' 41%" -- 2015/'16" 20_/_e" 151/'4" --
875/16" 41V4" -- 20_%6" 205/_e" 205/_6" --
92%" 41 _/4" -- 20_16" 205/16 " 257/16 " --
973/'4" 41%" -- 2015/;6" 205/16" 15Y_" 15%"
102_3/_" 41VZ' 35%6" 2015/16" 205/16" 205/16" 15%"
107%" 41V." 40%" 2O_/_e" 20%s" 20%6" 205/_6"
1121%_" 46%" 40%" 26" 20_A_" 20%6" 20"%_"
1t81/_" 46%" 45_/_6" 26" 205/_6" 205/_#' 26
Apply Prefix "O" for oil--"G" for gas "GO" for gas-oil. " Dimensions are approximate.
The manufacturer should be consulted before selecting a boiler for installations having unusual piping and pickup requirements, such as intermittent system operation,
extensive piping, etc For forced hot water heating systems where the boiler and all the piping are within the area to be heated, the boiler may be selected on the
basis of its Gross Output.

SERIES LC/LCE BOILER SPECS
• Cast Iron Sections- Factory
Tested
• Flex-Seal Gaskets
• Wet Base Desi_.. 50 PSI W.P.
• Insulated Enameled Steel Jacket
• Forced Draft Burner
(WU, SU Models)
• Combustion Chamber Cover
Plate, Insulated w/Observation
Port
• Ceramic Fiber Base Liner
• High Temperature Rope Seal
• Observation Port, Rear Section
• Front Cleanout Plate
• Cast Iron Rear Outlet with
Integral Damper (Series LC)
• Cast Iron Top Outlet with Flue
Collar (Series LCE)
• Lock Type Butterfly
Damper (Series LCE)
• Cast Iron Rear Cover Plate (Series LCE)
• Steel Channels for Field Assembly
• Integral Cast Iron Flue Collector
• One Low Water
Cut-Off (Packaged Boilers)
Water
•High Limit,Manual Reset
•OperatingControl
•Combination
Temperature-Pressure
Gage
•30 psi Safety Relief Valve
Steam
•High Limit,Manual Reset,
Pressuretrol
•Operating Pressuretrol
•Steam Pressure Gauge
• Gauge Glass w/Fittings
• 15 psi Safety Relief Valve
Model
Number
LC-04
LC-05R
LC-05
LC-O6
LC-07
LC-08
LC-09
LC-10
LC-11
LC-12
LCE-13
LCE-14
LCE-15
LCE-16
LCE-17
LCE-18
LCE-19
LCE-20
LCE-2r
LCE-22
LCE-23
Boiler
Model
Number
LC_4
LC-05R
LC-05
LC-06
LC-07
LC-08
LC-O9
LC-10
LC-11
LC-12
LCE-13
LCE-14
LCE-15
LCE-16
LCE-17
LCE-18
LCE-19
LCE-20
LCE-21
LCE-22
LCE-23
LCE-24
Length
78"
83"
83"
88"
93"
102"
107"
112"
117"
122"
127"
132"
137"
142"
151"
156"
161"
166"
171"
177"
182"
187"
Width
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
58"
Height
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
75"
Approx.
Shipping
Wt. (Ibs.)
2,645
3,075
3,075
3,505
3,940
4,370
4,805
5,235
5,665
6,100
6,495
6,970
7,405
7,840
8,280
8,720
9,165
9,605
10,050
I0,490
10,930
GAS GAS, OIL, GAS/OIL
Beckett Carlin Power Flame Power Flame Gordon Piatt Webster
Model
CFS00
CF800
CF1400
CF1400
CF1400
CF2300A
CF2300A
CF2300A
CF2300A
CF2300A
CF2300A
CF2300A
CF2300A
CF2506
CF2500
CF3500A
CF3500A
CF3500A
CF3500A
CF3500A
N/A
Model
JR15A
JR30A
JR30A
JR30A
JR30A
JR50A
JR50A
JRSOA
JR50A
C2-G
C2
C2
C2
C3
C3
C3
C3
C3
C3
C3
C3
Example:
Model
301HPA
301HPA
702CRD
702CBD
702CBD
702CRD
601CRD
801CRD
801CRD
501CRD
801CRD
801CRD
1050FFD
1050FFD
1150FFD
1150FFD
1150FFD
1150FFD
1150FFD
1150FFD
1150FFD
O - LC -06 - WU - STD -30PSI
/Sects. STD, IRI, FM
Series
Specify LC or LCE 15 PSI Steam (Std.)
30 PSI Water (Std.)
Blank = No Burner 50 PSi
O = Oil Water Steam 80 PSI
G = Gas W S = Less Burner
GO- Gas/Oil WL SL -Less Burner & Controls
WU SU = w/Burner& Controls
WUP SUP - Pkg. w/Burner & Controls
WP SP = Pkg. Less Burner
WLP SLP = Pkg Less Burner & Controls
Model
C1
C1
C1
C1
C1
C2
C2
C2
C2
C2
C2
C2
C2
C3
C3
C3
C3
C3
C3
C3
C3
C3
Model
$4.2
$4.2
R6.2
R6.3
R8.1
R8.1
R8.2
R8.2
R8.2
R8,3
R10.9
R10
R10
R10
R10
R10
R10.1
R10.1
R10.1
R10.1
R10.2
R10.2
i
Model
JB1C
JB1C
JBIC
JB1C
JB1C
JB1C
JB1C
JB1C
JB1C
JB1C
JB2
JB2
JB2
JB2
JB2
JB2
JB2
Ja2
JB2
JB2
JB2
JB2
m
PEERLESSHEATER CO.
231 North Walnut Street
Boyertown, PA 19512-1021
Phone: [phone] • FAX: [phone]
www.peerless-heater.com
ASME HI Division member • _1
of gama ganla
CUT-LC R7 (12/02.5M) Printed in US A @2002 peerPess Heater Compan

1,
USING THIS MANUAL
A. INSTRUCTION MANUALS .............. 1
B. SPECIAL ATTENTION BOXES ........... 1
PREINSTALLATION
A. ACCESSIBILITY CLEARANCES .......... 2
B. CLEARANCE FROM COMBUSTIBLE
CONSTRUCTION ..................... 3
C. COMBUSTION AND VENTILATION AIR .... 3
D. CHIMNEY OR VENT ................... 3
E. BOILER SETTING ..................... 4
E INSTALLATION SURVEY ............... 5
G. PLANNING THE LAYOUT ............... 5
H. VERIFY COMPONENTS ................ 5
A. PACKAGED BOILER .................. 12
B. ASSEMBLED BLOCK BOILER ........... 12
C. KNOCKDOWN BOILER - PLACING
THE SECTIONS ..................... 12
D. INSTALL COILS OR PLATES ............ 17
E. HYDROSTATIC TEST THE BOILER ....... 17
E APPLY CLEANOUT COVER PLATES ...... 19
G. INSTALL FLUE COLLAR ............... 19
H. INSTALL FLUE BAFFLES .............. 20
I. INSTALL CHAMBER LINER ............ 20
5, VENTING 27
.INSTALL THE BURNER
A. BURNER APPLICATION ............... 27
B. INSTALL BURNER MOUNTING PLATE .... 27
C. MOUNT THE BURNER ................ 27
7. CONNECT FUELPIPING
A. GENERAL .......................... 29
B. INSTALL FUEL OIL PiPiNG ............. 29
C. INSTALL GAS SUPPLY PIPING .......... 29
D. TEST GAS SUPPLY PIPING ............ 29
8, ;It
A. INSTALL SAFETY VALVES ............. 31
B. INSTALL BLOWDOWN VALVE .......... 31
C. INSTALL LOW WATER CUTOFF(S) ....... 31
D. INSTALL PRESSURE CONTROLS ........ 31
E. PIPETANKLESS HEATER(S) ........... 31
E CONNECT SUPPLY WIRING ............ 31
G. INSTALL CONTROL WIRING ........... 32
A. CHECK THE PIPING .................. 39
B. FILL THE BOILER .................... 39
C. RUN BURNER CHECK-OUT ............ 39
D. CHECK BOILER CONTROLS ............ 39
E. CLEAN THE BOILER .................. 39
A. PREPARATION ...................... 21
B. SUPPLY PIPING ..................... 21
C. RETURN PIPING ..................... 21
D. MULTIPLE BOILER INSTALLATIONS ..... 22
A. PREPARE THE PARTS ................ 25
B. APPLY JACKET SIDES AND CORNERS ...25
C. APPLY JACKET FRONT PANELS ........ 25
D. APPLY JACKET REAR PANEL .......... 25
E. APPLY JACKET TOP PANELS ........... 25
E APPLY PLATES AND LABELS .......... 25
A. PLACING BOILER IN OPERATION ....... 41
B. TO SHUT DOWN THE BOILER .......... 41
C. MAINTENANCE - ANNUAL ............ 41
D, MONTHLY MAINTENANCE ............ 42
E. DAILY MAINTENANCE ................ 42
A. SERIES LC BOILER ASSEMBLY ......... 46
B. SERIES LCE BOILER ASSEMBLY ........ 49

r*_l IL_['-'_I/:tII_/[e]L_I LvJ¥±_L_Ir-'_
The Series LC/LCE Installation, Operation &
Maintenance Manual is divided into four basic sections:
I. Preinstallation (Section I)
2. Installation (Sections 2 through 8)
3. Start-Up (Section 9)
4. Maintenance (Section 10)
:H _.'_'.,I:[_P_I! F-_III:IL_Ii[O]L_I ;{*):4:[,
Throughout this manual you will see special attention
boxes intended to supplement the instrudions and make
special notice of potential hazards. These categories
mean, in the judgment of the Peerless Heater Company:
Indicates a condition or hazard which may cause
severe personal injury, death or major property
damage.
Indicates special attention is needed, but not directly
related to potential personal injury or property
damage.

Theequipmentmustbeinstalledinaccordancewithinstallationrequirementsoftheauthorityhaving
jurisdictionor,intheabsenceofsuchrequirements,tothecurrenteditionoftheNational Fuel Gas Code, ANSI
Z223.1/NFPA 54.
Where required by the authority having jurisdiction, the installation must conform to American Society of
Mechanical Engineers Safety Code for Controls and Safety Devices for Automatically Fired Boilers, ASME CSD-I.
Carefully read these instructions and the Ignition System and Conbols Manual before beginning work. Understand all aspects of
the installation. Contact your Peerless Heater Company sales representative or customer service for help in answering questions.
This boiler must be installed by a qualified contractor. The boiler warranty can be voided if the boiler is not installed correctly.
Right Side View Rear View
Figure 1: Clearance Requirements
r,_l!
1. Clearances for service and from combustible surfaces
are the same for the LCE as for the LC. The
following recommendations allow for reasonable
access to the boiler. Follow local codes and
requirements when setting actual layout. See
Figure 1.
a) For installing, removing and servicing the burner:
provide 48" between the front of the boiler and
any adjacent wall or other appliance.
b) For access to the top of the boiler for cleaning
flueways: provide 24" above top of jacket.
c) For accessing and servicing of level controls and
inspection tappings (if used): provide 24"
minimum from the right side of the boiler to any
wall or obskuction.
d) For installation of jacket: provide at least 12"
from the left side of the boiler to any wall or
obstruction. More clearance may be needed for
longer boilers unless the jacket is pre-assembled
before placing the boiler.
e) For installation and removal of tankless heaters:
provide 45" between the end of the boiler and
any adjacent wall of obstruction. [This provides
for all available tankless coils. The spacing can
be closer for Heater Number X-1020 (allow 30")
or Heater Number X4021 (allow 35")].

h
oN [*.]-'liLVJlk_l:i'4[a):]LvJq_l
Provide the following minimum clearances to
combustible construction• See Figure i.
.,i [I,{.]_VJl:{l_"_l/[e]_._lf±lL'_llp]ivJ::lL_b/llV___l/[O]l._lV'_II;
2,
3.
4,
I Sides: 6"
2. Rear of Jacket: 6"
3. Front of Jacket: 24**
4. Top of Jacket: 24"
5. Steam and Hot Water Pipes: 6"
6. Vent or Chimney Connector: 18"
The installation must provide adequate air for
combustion and ventilation.
Unless the boiler room construction and natural air
infiltration are sure to provide all the air needed,
provide an opening or duct to the outside with a free
cross sectional area of at least I square inch per
4000 Btuh input for all installed appliances. At high
altitude, increase this requirement 4% for each i000
feet above sea level.
The boiler room must never be under negative
pressure. If exhaust fans or other equipment can
cause a negative pressure in the boiler room, the air
openings and equipment design must be engineered
to assure a neutral or slightly positive pressure in the
boiler room at all times of operation. If the
equipment design and air openings cannot assure
this, then the boiler must be located in an isolated
rOOM.
Using combustion air dampers:
a) If motorized dampers are used on the
combustion and ventilation air openings, wire
them such that they must open when the boiler
tries to operate• They must include a switch
which prevents the boiler from operating if they
do not open. See Figure 2.
I.
2
3.
4.
5.
6.
7.
Inspect the existing chimney or vent system Make
sure it is in good condition• Inspect chimney liner
and repair or replace if necessary•
The vent system and installation must be in
accordance with the current edition of the American
National Standard ANSI/NFPA 21 i, "Chimneys,
Fireplaces, Vents, and Solid Fuel Burning
Appliances", or applicable provisions of the local
building codes. The venting requirements for the
LCE are the same as for the LC. Figure 3 shows the
top flue outlet required on LCE boilers
Chimney/Vent Operation: The vent system must be
sized and installed to remove all combustion
products. If the vent system is not sized properly, the
burner may not operate properly. This can cause
poor combustion or sooting to occur.
If the vent terminates in an area where wind-
generated downdrafts are likely, install a suitable vent
cap which can control wind effects.
This boiler is designed to fire only with a pressurized
fire box. The breeching and vent may be sized for
negative, neutral or positive pressure (no more than
0.I inches water column at the boiler outlet) as
desired. But negative pressure overfire can cause
lifting of the flame and poor combustion or
overheating of the boiler crown sheet•
Forced draft breechings and vents must be sealed
and of heavy gauge steel construction and must
comply with all applicable codes of construction.
The vent diameter and minimum height for stub
vents are listed in the Ratings and Dimensions
Section of this manual. Always extend vent
terminations at least 3 feet above the roof line. See
Figure 3.
Failure to provide adequate venting can result in
severe property damage, personal injury or death.
IBurner Wired to Open Damper
i_ on Call for Heat
EdSdw/_cV-htC-phrovesDamper Open
Then Allows Burner to Start
Motorized Combustion
Air Damper, Typical
Burner
Figure 2: Motorized Vent Dumper Interlock Figure 3: Vent Termination, Typical

Figure 4:
FOUNDATION LENGTH
JACKET LENGTH
SECTION LENGTH
Steel Channels, Supplied in Baffle Carton
Leg Locations
I
Foundation Layout
8. Exterior Vents:
a) Insulate sufficiently to ensure adequate draft and
to prevent vent damage due to condensation.
I=lli :{0] II =1;__-'1:11/ I_f{
9. Vent Connection to Boiler:
a) Support the weight of the vent system
independently of the boiler flue connection.
b) Provide support of the vent connector
(breeching) at maximum 12 foot intervals to
prevent sagging and to provide a minimum
upward slope of i/4" per foot.
10, Do not vent natural draft appliances in a combined
vent which operates under positive pressure.
11. Draft Regulator: Install a barometric draft regulator
where using high chimney or any high draft vent.
This is needed to prevent causing negative draft in
the boiler Excess draft will cause flame lifting and
possible impingement.
12. The Draft Damper for the LCE boiler is a separate
piece, shipped in the Top Flue Outlet Carton.
a) Install the Draft Damper as close as possible to
the boiler flue outlet. It can be installed vertically
or horizontally provided that the connecting vent
piping and fittings are designed and installed for
pressurized service.
b) Secure the damper to the vent with screws and
seal the joints with a bead of high temperature
silicone, sealant (found in Section Assembly Kits).
c) The vent must be installed so it can be
disconnected and the Top Flue Outlet removed
for proper cleaning of the flueways.
1.
2.
If the boiler room floor is not level or if additional
structural support is needed, provide a good, level
foundation for the boiler with the minimum
dimensions given in Table 1. The flooring and
structural support system must be suitable for the
operating weight of the boiler and any connected
piping. Place the Steel Channels on the foundation
as shown in Figure 4.
Do not operate the boiler until the foundation, if new
concrete, has thoroughly cured. The concrete might
be damaged if heated too quickly due to the
entrained moisture remaining.
Do not install this boiler on carpeting or any
combustible flooring. A significant fire hazard could
result, with potential for property damage, personal
injury or death.
3. Ifthe boiler is installed in a penthouse or if wiring of
any sort is run underneath the boiler foundation,
construct the foundation with provision for air flow
underneath between the main floor and the top of
the boiler foundation.
a) An acceptable foundation would be concrete
blocks laid with the openings lined up.
4

Table 1: Foundation Lengths :Pl gA=1."tI_i_[o] L'_I:,[o1L_I=1L_iiI_
b}
Model Foundation Length, Inches
LC-04 37"/_,
LC 05 42:_,_
LC 06 47V_,
LC-07 521/z
kC-08 57%
LC-09 62%
LC 10 67:_/4
LC 11 72%
kC-12 77%
LCE 13 83'/2
LCE-14 889/16
LCE-15 935A_
LCE-16 98nA6
LCE 17 1033/4
LCE-18 108Wl_
LCE-19 1137/8
LCE 20 118_5/,6
LCE-21 124
LCE-22 129'/16
LCE-23 134'/8
LCE 24 139_/1_
If the foundation must be a concrete slab, use an
air cell high temperature insulating board, at least
I/2" thick, with aluminum backing, aluminum
side up. A I/2" thick high temperature millboard
with aluminum backing is acceptable as well.
Place the insulating board on the slab between
the steel channels.
I_1 IIL_k'tl If;1! IL*_III[o] L_l.'t I J:{vJa '
For new and existing installations, a Steam Installation
Survey is available from Peerless Heater Company. The
survey will provide information on how a steam boiler
works with your specific system and will provide an
overview of steam system operation in general.
You can also use this survey to locate system problems
which will have to be corrected. To obtain copies of the
Steam Installation Survey, contact your Peerless
representative.
I.
2.
3,
Packaged: All components should be inside crate. In
some cases the burner may be shipped separately,
Optional equipment, such asbarometric draft
dampers, may also be shipped separately.
Knockdown: All components shipped for field
assembly, See Table 2 for standard components. See
Tables 3 through 8 for optional components.
a) Channel Rails
b) Sections
c) Assembly Kit Carton(s): Includes flow port
gaskets, tie rods with hardware, high temperature
rope, and deanout cover plates.
d) Flue Box Carton: Includes flue box, rear flue
cover plate (LCE only), rear observation
assembly and port cover plates.
e) Baffle Carton
i) LC: Includes baffles, combustion chamber
liner, rating label and ASME plate
ii) LCE-21 through LCE-24: Baffles
f) Jacket Cartons
g) Draft Damper (LCE only)
h) Label Carton (LCE only)
i) Burner Mounting Plate
j) Trim Carton: Includes safety valve and pressure
gage
k) Control Carton: Limit controls
I) Tankless Heater(s}
m) Additional controls and fittings
Assembled Block: Same as knockdown except
channel rails, sections and assembly kit cartons are
assembled into a block as a single shipping level
component.
[_ I:JIF_'I_I_IIL_[€: ii:l_ ilr;\Y.lll
Prepare sketches and notes of the layout to minimize the
possibility of interferences with new or existing
equipment, piping, venting and wiring.
5

(3) Table 2A: Series LC Shipping List
Standard Sections (_e Table 3for Optionsl
Boiler Channel 1" Carton Contents Contents Front/Rear
Model Rail Plain LWCO 3" Tap. (_ Table4 S¢¢Below SeeBelow _nels
Number Bundle Front Back lnterm, lnterm. Interm. forOpfions) Item1 Item2 Hardware
] PartNo. LC.I00I LC.1007 LC.1000 LC.,000 1LC-I023 LC 1022 LC-5004 LC 6016
Label LC-04 A A
Stock Code 90160 8613(30 86022 86004 86005 85004 86050 8_5040 86030
LC-05R Quantity 1 ' l 2 I 1 I ] '
Part No LC 1001 LC 1007 LC ,0O0 LC ,0(10 1 LC 1023 LC 1022 1 LC 5004 LC 6016
Label LC-05 B A
Stock Code 90161 86000 86022 86004 860(35 85105 86051 86040 86030
LC-05 Quantity 1 1 i : 2 ' ' 1 1 1
Far{No ' LC-1001 LCI007 :LClO00 LC1000I LC,023, LC10221 LC5004 LC6016
Label LC-05 B A
[S_ockCode 90161 86000 _ 86022 86004 86005 85005 ; 86051 86040 86030
LC-06 Quantily 1 1 1 ! 3 I I I 1 1
Part No LC-1001 : LC-1007 LC-1000 LC 1000-1 LC-1023-2 LC-1022-2 LC 5004 ]LC-6016
Label i LC-06 C B
Stock Code 90162 860(X] 86022 85004 86005 85006 86052 8604, 86030
LC-07 Q_anti_ ,1]4 1 1]1 ]
Part No LC '00' LC i007 LC i000 LC 1000 l LC 1023 3 LC 1022 3 LC 5004 l LC 6016
Labe[ LC-07 D B
Stock Code 90163 86000 86022 86004 86005 8,5007 86053 86041 86030
LC-08 QuanlJ_ 1 1151 11111
Part No LC 1001 LC 1007 LC 1000 I C I000 1 I.C 1023 4 1C 1022 I C-1022 1 ! C 5004 i i C-t_016
Labe] LC 08 A B B
Stock Code 90164 86000 86022 86004 86005 85008 86050 86051 86041 8(_030
LC 09 Quantity l i i 6 i l 2 l i
Part No LC-1001 LC-1007 LCd000 LC-10_0.1 LC-I023-5 LCd022-1 LC-5004-2 LC-6016
Label LC-09 BC
s,o_,Codo 9o1_ _ooo _ _022 _®€ s600s _9 _o51 860,_2 _o3o
LC-IO Quantity 111 7] 1' 11'
Part No LC-1001 LC-1007 LC-1000 LC I000 1 LC 1023 6 LC 1022 I LC-I022-2 LC 50(]4-2 [C 6016
Labor LC '0 BC C
StockCode 90166 86000 86622 86004 _1_005 85010 8605, 86052 _W)42 86030
Part No LC 1001 LC-1007 LC i000 LC 1000 1 LC 1003 LC 1023 7LC 1022-2 LC 5004 2 LC 601(3
Labor LC-II CC
Stcck Code 90167 86000 86022 86004 86005 86008 85011 86052 86042 86030
LC-12 Quantity 1 1 1 8 1 1 I 1 1I i
Part NO LC 1001 LC ]007 LC I000 lC I000 1 IC 1003 lC I023 8 LC I022 2 LC-1022 3 LC 5004 2 LC-6016
Label [ C 12 C D C
!
Stock Code 90168 8_O0 86022 86004 86005 8Z)008 _'k_012 86052 86053 _042
Baffle Assembly Kit Ctns. Flue C_. Jacket Cartons (TblSOpttom}
86030
Top'Side
Panels
Hardware
Chamber Liner
l
LC 6017
A
86031
1
LC 6017 1
B
86032
1
LC 6017 1
B
86032
1
LC 6017-2
C
86033
1
LC 6017 3
D
86034
1
{C 6017 IC6017 I
A B
86031 86032
2
LC-6017 1
B
86032
1 1
LC 6017 I LC 6017-2
B C
86032 860.%
2
LC 6017 2
C
86033
1 1
[.C 6017 2 LC 60] 7 3
C D
86033 86034
i Assembly Kit Cartons Contents: Flow Port Gaskets, Silicone Sealant, Tie Rods, Washers, Tie Rod Nuts, Section Seal Rope, Rope Adhesive, Cleanout Plates, Mounting Hardware
2 Flue Box Carton Contents: Hue Box, Seal Rope, Observation As3,embly, Coil Cover Plates, Cover Plate Gaskets, Moun8ng Hardware

"-q
Table 2B: Series LCE Shipping List
][Standard Sections (See Table 3 for Optionsl Barge Assemb]_ Kit Cartons Flue Ctn. Jacket Cartons (s_ Table 5 Io_ Omionsl LbL Ctn.
ITop Std.
Boiler Channel :Top 1" Carton FIo_ P_rt Gas]_ets Silicone Sea_nt, ¢onlents Fmn_Rear Panels
Model J Rail !Flue LWCO 3" Tap, Plain is_*T_bJ.4 T,eRodsWashersTi_RMNu_ S_ckio_S_alRop__ Draft
Numbel" Bundle I FTont I Intern1. ; [nterm. Internl. Interm. iBack for Optmns! R°P_ Adhesive Cleanout Plates, Mounting Hardware I Se e Below Panels H_rdwar_ Ratira_
;Irem lHardware Chamber LLner Damper Label*
LCE-13 i i
LCE-14
C E
86052 i 86054
1 I
D E
_,6()53 86054
LCE 15 1 1 ]
A R E
_6_]5(/ 86051 86054
LCE-16 2 1
Quantitv :1 1 3 1 :1 6 l
Part No LC-103I LCE1056 LC 10C_ 1 LC 1003 i LC 1090 LC 10_37
!
Label I ! i
C_a,_tiW_I 2 [ 1 • 3 ;z6 .:1
ParENo LC.1001 i LCE 1056 LC 1000-I LC 1003 LC 1LY_ LC 1£X)7
Label
Stock Code 90162 86003 86100 86035 86008 86(104 860'22
Quanti_ 2 l 3 1 2 7 1
PaaNo LC-lC_I LCE 1056 LC 100¢ 1 LC 1C¢3 LC I_,F0 LC 1007
i
Labor
Sio,ck Code 90163 _ i 86100 86005 86008 86004 ; 86022
Quanfil,j 2 l ;3 l 2 8 l
F_rt _o LC 1C_I LCE 1056 LC i00_ i LC 1003 kC lOgO LC 1007
Label 4[ ' ,_+
Sto_kCod; l 90163 : 86_0 :86100 '86005 : 86008 ' 86004 [ 86022
I3 1 3 _ i 1
LC-I _)l LCE 1056 LC IO00 l LC 1003 LC 100¢ LC 1007
[ 8600_ 86100 86O35 86008 86O04 86022
3139I
LC.IOD1 LCE.I056 LC I(X_A] I LC 10_33 IC If_O LC 1_07
B E
8_051 8(,,054
1 1LCE-I? Quanlily i 2
Part NO
Label
Sleek Code 90164
LCE 18 Qua_tlt_ 2
Parl No
Label
Stock Code 9016_
LCE 19 Quanmv 2
1
E
86O54
B c
86(151 8_052
2I
c E
86100 86005 8N'_38 86004 86[322 86052 86054
1
LC 5011
DA
86043 86030 F_5_I1
I l 2
LC 5011 LCE 6016 LCE.6017 1
D B
8(_O43 : 86030 86032
I 1 i ]
LC5011 LCE6016 LCE60171 ICE60172
D B C
86043 86030 86032 660_
1 1 2
LC 5011 LCE 6016 LCE 6017 2
D C
86030 85033
i I l 2
LC.5011 LCE.6016 LCE b_17 LCE 6017 1
D A B
86043 86030 86031 86032
1 1 3
LC 5012 LCE 6016 LCE 6017 1
E B
86044 86030 86032
1 1 1 l 1 l
LCE6016 i LCE6OI7 LCE6017 I LCE6023 $50_73 LCES028
B E A
B6032 860q4 q0523 85013
1i1
LCE N)23 S 5007 3 LCE 81328 1
E A
8N194 9052_ 85014
l:l
ICE 6023 6 ,t_17 3 LCE _U2'3 :
E A
86094 90523 85015
II1
LCE 6O23 S fl(x_7 3 LCE _(],_8 3
E A
86094 9(_52:] 8._16
1 E l
LCE 6023 S 5007 3LCE t_02S 4
E A
8_194 90523 _:5017
1 1 1
1CE ()023 % F,O(_74 I CE _)2_ 5
E [l
8609,1 9(_524 _5(_1_.
1 3 1 3 10 1 1 ] / l 1 2 1 [
Part No LC.1001 LCE 1056 I.C 1000 I [ C 1003 [C 1000 LC 1007 LC r_12 LCE 6016 LCE 6017 I [ CE [)(117 2I CK 602_
Label C D E E B C K
Stuck Code 90165 86030 86107 86N/5 86008 825004 86022 86052 86053 86054 86044 8€1130 86032 86ql3 86094
i
LCE-20 Q_a_iW z i ;! 1 4I0 I z I 1 I 2z
i i
P_rlNo LCI00I LCEI056 LCI0_I LCI003 LCIOGO LCI007 LC.5012 LCE6016 I.CENII7 lCEbOlTl LCE6023
1
e _ :Lal_l I , _I 'o_,_ '[/ D E E A B E
otc_k _c&, 9(1165 86000 100 _ 8N)08 _ 86022 86053 86054 86044 86o:m 86o31 86o32 _6c,'94
LCE-21 Quantil_ 2 . l J 3,1 .q[ II L } l l 1 ] ,1 l _1 1 1 3 ]
PartNo LC.I(_I i LCE1056 LC-1000-1 LCl003 LC-10C_ l LCI0_7 LCEI074 LC5012 LCE6OI6 LCE6017 LCE6OITI LCE_323
La_, _ ' _. __ : t l:A B D E E A B E
S_o_kCo& I9O166 _ 8610_ I _5 ! 86o¢8 86oo4 86o22 _ _113 P,6_35o 86_51 86o53 86O54 8,5O44 86O30 86O31 86032 86094
I
LCE-22 Quantity [ 2 1 314, 12 1 1 21 1 11 I 4I
i]LCE1o56+LC :c_]:; ! LCI0_3 [ LCI000 "LCI007 LCE1074 LC5012 LCE6OI6 'LCE6OI71 LCE6023
Part No LC 1(1131
Label _ B D E E B [2
Stc<k Code 90166 NNI00 _ 86100 86005 86908 86004 i 86022 86113 86051 8605,3 86054 86044 86030 86032 86094
LCE 23 Quantity 2131 4 13 l 1 1 1 1 1 1 1 1 3 1 1
i
ParlN° iLC'IC_)I LCE1056 I LC-I0001 LCI(X)3 LC.10,P_ iLC-1007 [CE-1074 I.C5012 LCE6016 ICE6OlT] 1CE60172 I.CE6021
iD E E B C E
Slake _ 86100 86035 l 86038 86004 ! 86022 8,5113 86051 86052 860,_,3 g,5_54 8,5044 86030 861132 86033 b_5094
i
Qu_n_W I2] ; 3]!4 14 l :2l:]l2z i
LCE-24 PartNo. I l Lci001 ]LCEI056 :LC10_)I I LC-1003 LC-IO00' LC-1007 LEE-1074 i [
l [ :, _] i-- DIE _ i LC 5012 LCE 6016 LCE 0017 i "CE 6017 2 LCE 6023
L_: I,c i E B C E
1 Flue Box Cm'lon C_ntent_: Top Flue Plate, P,enr Hue Cover, Seal Rope, Observalion Assemblp, Coil Couer Plates, Cover Plate, Gaskets, Mounting Hardware
] ]
_, 51_J7 4 tCE ,_028 r
B
,Blf124 NS[llq
]
6,(HJ7 4 LCE _()2g ]
B
9q524 g5o20
I I
S 5007 4 LCE 8028
B
q0524 85021
1 1
S 5(,_}7 4 [CE MI]2_ (
B
_]524 g5022
;[
-, _,1_7 4 LCESOZB ](
R
9O524 85O23
]!
S o0_17 4 LCE<_02_ 1 ]
B
9t_24 K5024
*See Table 4 for Options

Table 3: Standard and Optional Sections for Knockdown Boilers
Sections
15 psig Steam MAWP
Standard
Part #Stock Code
Front LC-1001 86000
Intermediate LC 1000 86004
LWCO Intermediate LC-IO00-1 86008
Top Flue Intermediate LCE-1056 86100
3" Tapped Intermediate LC-1003 86008
Closed Back LC 1007 86022
Coil Back LC- 1002 86036
wflnspectionTappings
Pad #ITPStock Code
LC 1013 86010
LC-IO14 86014
LC 1014 286092
LCE-1064 86110
LC-1015 86016
LC-1016 86018
LC 1017 86026
Table 4: Standard and Optional LC Baffle
Cartons and LCE Label Cartons
Standard 15 psig steam
Model 15 psig steam MAWP
MAWP Canada
USA
LC-04 85004 85204
LC05R 85105 85505
LC-05 85005 85405
LC-06 85006 85206
LC-07 85007 85207
LC-08 85008 85208
LC 09 85009 85209
LC-10 85010 85210
LC-I1 85011 85211
LC-12 85012 85212
LCE 13 85013 85213
LCE 14 85014 85214
LCE 15 85015 85215
LCE-16 85016 85216
LCE 17 85017 85217
LCE-18 85018 85218
LCE-19 85019 85219
LCE 20 85020 85220
LCE-21 85021 85221
LCE-22 85022 85222
LCE-23 85023 85223
LCE-24 85024 85224
Table 5: Standard and Optional Jacket Cartons,
Top/Side Panels
Standard
Jacket Label (No Inspection With Inspection
Tappings) Tappings
A 86031 86101
B 86032 86102
C 86033 86103
D 86034 86104
E 86094 86097
Note: Boilem with inspection tappings in front and back sections only use
s_ndard ca_ons.
Table 6A: Burner Mounting Plates
Boiler Model
Model
LC-04 LC-05R LC-05 LC-06 LC-07 LC-08 LC-09 LC-10 LC-11 LC-12
86070*
Beckett 86069* 86069* 86069* 86074" 86074" 86674* i 86074* 86074*
! i
C_li. 86o69* _69. i ;i
(Jordon
Piatt
86070*
86070* 86070*
86070* 86070*
CF-800
CF-1400
CF-2300
301CRD
702CRD
801CRD
$4.2
R6,2
R6.3
R8.1
R8.2
R8,3
CI
C2
JI5A
J30A
J50A
JBI
T
i
i 86079
86069* 86069*
86078 86078
86071 86071
86072 86072
86079
86071
86072
86071
[
I
86079 [86079 86079 86079
86076 86076
86071 86071
Power 86076 86076 86076
Flame 86072 86072
86077 86077 86077 86077
Webster 86071 86071 86071 86071 86075 86075 86075 86075 86075
* Standard Burner Mounting Plate
{3

Table 6B: Burner Mounting Plates
Boiler Model
Model
LCE-13 LCE-14 LCE-15 LCE-16 LCE-17 LCE-18 LCE-19 LCE-20 LCE-21 LCE-22 LCE-23 LCE-2
CF2300AKG 86074*
CF2300AKB 86083* 86083* Not
Beckeit CF2500 86074* 86074* Available
CF35(K)ARM 86083* 86083* 86083*
CF3500PJKL 86080* 86080*
80ICRD 86073 86073
Carlin 1050FFD . 86086 86086 N/A
I150FFD 86087 86087 86087 86087 86087 86087 86087
R10.9 86088
Gordon R10 86088 86088 86088 86088 86088
Plait R10.1 86088 86088 86088 86088
R102 86088 86088
Power C2 86076 86076 86076
Flame C3 86080 86080 86080 86080 86080 86080 86080 86080 86080
Webster JB2 86081 86081 86081 86081 86081 86081 86081 86081 86081 86081 86081 86081
*Standard Burner Mounting Plate
Table 7: Trim Cartons
Model Stock
Code Label
LC-04
LC-05R
LC-05
LC 06
LC-07
LC-08
LC 09
LC-10
LC-11
LC-12
LCE-13
LCE-14
87000 A
87000 A
87000 A
87O00 A
87000 A
87000 A
87001 B
87001 B
87001 B
87001 B
87002 C
87002 C
LCE-15 87002 C
LCE-16 87002 C
LCE-17 87003 D
LCE-18 _ 87003 D
LCE-19 87003 D
LCE-20 87003 D
LCE-21 _ 87003 D
LCEo22 87003 D
LCE-23 87004 E
LCE-24 87004 E
1 Safety Valve selection based on capacity
determined by boiler output (Gross I=B=R Output).
Applies to most locations in United States and Canada.
Table 8: Control Cartons
!
Model Stock Code Label
LC-04
Through 88511 Steam
LCE-24
9

Rear Flue Box
F
R
0
N
T
R
E
A
R
Figure 5: Series LC Boiler Assembly - Right Side View
10

=3'
€Flue Rear Flue
Cover
®
(4
r-
i11
m
o_,
,,R
>
f_
O"
I
FR
_: R E
< o A
N R
T