PEERLESS CL-ENCL68 User manual

12015-02-05 #:220-9004-2 (2017-01-03)
SMALL FORM FACTOR
ELECTRONICS ENCLOSURE
MODEL:
CL-ENCL68
CL-ENCL68-EUK
User Manual
www.peerless-av.com

22015-02-05 #:220-9004-2 (2017-01-03)
General Safety Precautions ...................................................................................................................3
Relevant Information .............................................................................................................5
System Installation And Electrical Requirements ..................................................................................6
Electrical Code...............................................................................................................................6
Power Source ................................................................................................................................6
Set Up Instructions.................................................................................................................................7
What's In The Box..........................................................................................................................7
Cable Entry/Exit..............................................................................................................................8
Installation Of Electronics...............................................................................................................9
Closing the Electronics Enclosure................................................................................................10
Mounting the Media Player Enclosure (Optional).........................................................................11
Powering Up ................................................................................................................................12
General Care Instructions ............................................................................................................12
Product Specifications .........................................................................................................................13
Warranty ..............................................................................................................................................14
CONTENTS

32015-02-05 #:220-9004-2 (2017-01-03)
Read before operating equipment
Thank you for purchasing our product. Before using it, please read this user manual carefully
and follow the instructions correctly for safe operation. Please keep this manual handy for future
reference. Also, please be sure to always include this user manual in the packaging when transferring
or transporting this product to a different location.
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of
electric shock, do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
6. Protect the electrical cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
7. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as electrical-supply cord or plug is damaged, does not operate
normally, or has been dropped.
8. Only use attachments/accessories specified by the manufacturer.
9. In case of emergency such as fire or electric shock caused by the product, immediately contact
911 or proper emergency police/fire service agencies in your country.
10. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
11. Use properly rated electrical voltage. Use of non-rated voltage may cause fire, electric shock and
severe damages to the product.
12. Do NOT, under any circumstances, modify or disassemble this product as it may cause fire,
electric shock, or severe damages to the product. Also any unauthorized modifications made to
the product automatically void product warranty.
13. Never touch antenna lines or wires, electrical cables or plugs when lightning or thunder is present
as it may cause electric shock.
14. Any severe physical impact on the product may cause certain components to fall out of place
within and break, which may cause fire or electric shock. In such event, do not operate the
product. Contact the manufacturer for support.
15. Periodically clean dust off the electrical plug, to keep it clean and dry, ensuring proper and safe
operation of the product.
16. Do NOT destroy, process, or place close to any heat source; do NOT bend or twist electrical
cords, electrical plugs, cables, or wires with excessive force; do NOT place any heavy object on
the display as all of the above may cause damage resulting in fire or electric shock.
17. Do NOT touch electircal plugs with wet hands.
18. Always make sure to plug in the electrical plug firmly and completely. Incompletely placed
electrical plugs may cause fire or electric shock due to built up heat emission.
19. Do NOT use any non-rated electrical sockets or power strips with many other devices jointly
plugged in. The wire of non-designated capacity may cause fire due to built up heat emission.
Try to use a single, directly dedicated and rated GFCI electrical outlet for the product for safe
operation.
GENERAL SAFETY PRECAUTIONS

42015-02-05 #:220-9004-2 (2017-01-03)
20. In case of product malfunction or unusual events such as electrical burning smell, smoke, due to
internal overheating, immediately turn off and unplug the power and contact the manufacturer.
21. Do NOT install the product at such unstable locations as moving objects, constantly vibrating
props, or uneven surfaces. Improper installation may cause products to fall off. Follow mounting
instructions properly for safe operation of the product.
22. Do NOT install the product near any poisonous gas or chemically unstable atmosphere as it may
cause fire.
23. Do NOT install the product near any strong magnetic or electrical current field. It may cause fire,
electric shock, or severe damages to the product.
24. Do NOT leave any fire source, such as candles, close to or on the product as it may be a cause
for fire or damages to the product.
25. Do NOT move or transport the product with any cables (power cables, content connectivity
cables) plugged in to the source devices. Damages may occur to the cables, plugs, or jointing
connectors of the cables due to forcible bending and stress, which may cause damages to the
waterproof seal of the product, making it subject to fire, electric shock, or shorted circuit.
26. When unplugging, always grab the plugs of power cords or cables. Improper pulling of the cords
or cables may cause damages to the waterproof seal of the product, making it subject to fire,
electric shock, or shorted circuit.
27. Do NOT use any other power cords or connection cables than what is provided with the product
or from the manufacturer directly. Use of untested, unauthorized, or substituted power cords or
connection cables may be a cause for malfunction, fire, electric shock, or severe damages to the
product. Also such use of improper or undesignated power cords or connection cables will void
product warranty.
28. Always leave the Power Off when plugging or unplugging the power cords or connection cables to
avoid electric shock or damages to the product.
29. Do NOT use any chemical such as paint thinner or benzene to clean the product’s exterior. It may
cause scratches on the surface, erasing proper indications, identification labels, or instructions on
the exterior, which may be a cause for misuse and improper operation of the product.

52015-02-05 #:220-9004-2 (2017-01-03)
Relevant Information
Once the Electronics Enclosure is installed, there is limited access to the electrical device inside. For
future reference please record the device's serial number below.
Electronics Serial Number ____________________________________

62015-02-05 #:220-9004-2 (2017-01-03)
Electrical Code
Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of
the National Electric Code that provides guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding system of the facility. Outlet shall be
installed near the equipment and shall be easily accessible.
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150
to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.
Power Source
The product must be connected to a main socket outlet with a protective earthing connection.
The main plug is used as the disconnect device and shall remain readily accessible.
This product operates on 100-240 volts 50/60 Hz, AC current. Insert the power cord into a 120 volts
60 Hz outlet. Never connect the product to direct current or anything other than the specified voltage.
To prevent electric shock from the product, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
CAUTION: Double pole/neutral fusing (ISO 3869. No 5036)
Antenna discharge unit
(NEC Section 810-20)
NEC National Electric Code
Ground clamp
Electric service
equipment
Ground clamps Power service grounding
electrode system
(NEC Art 250 Part H)
Grounding conductors
(NEC Section 810-21)
Antenna lead-in wire

72015-02-05 #:220-9004-2 (2017-01-03)
Important:
1. When routing cables through the cable entry make sure that the cables are formed in such a way
as to remove any stress on the connectors.
2. Electrical installation shall be in accordance with the applicable parts of Chapter 8 of
ANSI/NFPA70.
What's In The Box
SET UP INSTRUCTIONS
Parts List
Part # Description Qty
Aelectronics enclosure 1 CL-ENCL68
BM4 x 18mm socket screw 4 SCR-0055
Cdual lock 1 x 1.5" 4 600-1009
Ddual lock strips 3M 4 600-1393
E4mm allen wrench 1 560-0072
F3/32" allen wrench 1 560-1034
M4 x 18mm
electronics enclosure
B (4)
A (1)
C (4) D (4)
dual lock 1 x 1.5" dual lock strips 3M
E (1) F (1)
4mm allen
wrench 3/32" allen wrench

82015-02-05 #:220-9004-2 (2017-01-03)
1. From the bottom of the unit, unscrew the 4
screws at each corner of the aluminum base
plate and remove the plate.
2. Route the cable(s) for the electronic device
through the cable entry points on the
Electronics Enclosure as shown.
Note: It is suggested to only use one of the cable
entry points.
Note: Do not run the electronic devices power
cord through either of the entry points at this
time. The power cord will be installed later.
Cable Entry/Exit
3. Realign the metal base plate on the
Electronics Enclosure. Reinstall the 4 screws
into the metal base plate while making sure
the cables are fully sealed (Cables should be
completely surrounded by the compressible
foam gaskets and gasket block).
Note: Ensure that the base plate is reinstalled in
the proper orientation.
Before starting the installation of any electronic
devices, ensure that the Electronics Enclosure
electrical cord is not plugged into electricity.
Failure to do so may result in injury or death.
For reference, the Electronics Enclosure is
equipped with a plastic top and aluminum base.
BOTTOM
BOTTOM

92015-02-05 #:220-9004-2 (2017-01-03)
1. From the top of the Electronics Encloser,
unscrew the 4 screws around the perimeter
and remove the plastic top.
5. Note: Electronic devices should be kept at
least 1/2" from the internal fans for proper
air flow. Apply velcro pieces (D) to lid as
shown. Once the Velcro has been applied
to the bottom of the electronic device and
the bottom of the enclosure lid, remove the
exposed release liner and carefully place
the electronic device inside the Electronics
Enclosure allowing for equal clearance on
all sides and clearance for cables. Once
positioned, press down firmly for a few
seconds to set the adhesive.
Installation Of Electronic Device
2. Plug the electronic device electrical cord or
power supply into the electrical outlet located
inside the Electronic Enclosure.
3. Connect all other cables to the electronic
device.
4. Remove the release liner from one side of
the adhesive on the 4 Velcro pieces provided
(C). Attach the 4 Velcro pieces to the bottom
corners of the electronic device (sold
separately).
Electronic device
(sold separately)
C (4)
D (4)
TOP

10 2015-02-05 #:220-9004-2 (2017-01-03)
Closing the Electronic Enclosure
Note: If mounting the Electronics Enclosure using an Outdoor Display (TV) Wall Mount, completely
close the Electronics Enclosure prior to mounting.
1. Connect all electronics to confirm power and connections are correct and functioning properly
prior to final closing and mounting of the Electronics Enclosure.
2. Ensure the electronic device power switch is set to "On" (if applicable) and the electronic device
settings are set to power the unit "On" when electricity is applied (plugged in).
Note: Once the Electronics Enclosure is closed, there will be no access to the electronic device itself
without reopening.
3. Test the functionality of the Electronics Enclosure's heating and cooling system by plugging in the
electrical cord to a 100-240VAC 50/60Hz GFCI electrical outlet (ensure the aluminum base plate
is installed prior to this step, if not, install now). Once electricity is applied, the unit can be tested
by pressing the three (3) buttons, one at a time, on the top of the internal mesh cage.
• Button A - All 4 fans will run for 30 seconds
• Button B - The surface of the enclosure between the two internal fans will warm slightly for 30
seconds (this can be felt by touch or by IR heat meter)
• Button C - The surface of the enclosure between the two internal fans will cool slightly for 30
seconds (this can be felt by touch or by IR heat meter)
If all functions are working properly, proceed to step 2, if not contact your Peerless-AV Customer
Service Representative.
Note: The test above can be done at any time to verify the unit is working properly.
4. To close the unit, realign the plastic top on the Electronics Enclosure and reinstall the (4) M6 x
18mm screws securing the plastic top to the Electronics Enclosure. Then, install (4) M4 x 18mm
screws (B).
Note: Do not overtighten screws
Note: Ensure that the aluminum base plate and
plastic top are reinstalled in the proper orientation.
B (4)
TOP