PEERLESS DS-VW650 Guide

ISSUED: 09-24-10 SHEET #: 125-9146-2 (6-25-13)
Visit the Peerless Web Site at www.peerlessmounts.com
1 of 5
Installation and Assembly:
Wall Mount
Model: DS-VW650
A B C
D E F
G
H I J
Description Qty. Part #
Awall plate 1 145-1199
Block bracket 1 145-1201
Cvertical bracket 2 145-1200
DM5 x 10 mm socket pin Type F screw 2 520-1164
E#14 x 2.5" hex head wood screw 6 5S1-015-C03
Fconcrete anchor 6 590-0320
G4 mm allen wrench 1 560-9646
Hnylon shoulder washer 4 590-2233
IM6 x 12 mm phillips screw 4 5201128
JM8 x 15 mm phillips screw 4 520-9257
Parts List

ISSUED: 09-24-10 SHEET #: 125-9146-2 (6-25-13)
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 5
Installation to Wall Stud
Use a stud nder to locate the edges of the stud. Use of an edge-to-edge stud nder is highly recommended.
Based on their edges, draw a vertical line down the stud center. Place wall plate (A) on wall as a template.
Level plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud
centerline. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate (A) is level,
secure it using six #14 x 2.5" wood screws (E) as shown below.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is rmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud nder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
1
E
A
Stud

ISSUED: 09-24-10 SHEET #: 125-9146-2 (6-25-13)
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 5
E
F
A
solid concrete
cinder block
Installation to Solid Concrete or Cinder Block
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
1
3
2
F
Drill holes and insert anchors (F).
Place plate (A) over anchors (E) and secure with screws (F).
Tighten all fasteners.
A
F
E
concrete
surface
• Tighten screws so that wall plate is rmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
nishing material. If mounting to concrete surfaces
covered with a nishing surface is unavoidable,
the nishing surface must be counter bored as
shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywall is thicker than 5/8" (16 mm), custom
fasteners must be supplied by installer
WARNING
Make sure that wall plate (A) is level, use it as a
template to mark six mounting holes. Drill six 5/16”
(8mm) dia. holes to a minimum depth of 2.5” (64
mm). Insert anchors (F) in holes ush with wall as
shown (right). Place wall plate (A) over anchors and
secure with six #14 x 2.5” screws (E) as shown.
Level, then tighten all fasteners.

ISSUED: 09-24-10 SHEET #: 125-9146-2 (6-25-13)
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 5
3Hook adapter brackets (C) to wall plate (A). Slide adapter brackets (C) to position.
Once display is located in desired position, secure with lock bracket (B) using two M5 x 10 mm socket pin Type F
screws (D) to lock in place as shown in gure 3.2.
Attaching Adapter Brackets to Wall Plate
BACK FOR WALL PLATE
SUPPORTING SURFACE
NOT SHOWN FOR CLARITY
Attach adapter brackets (C) to display using four M6 x 12 mm phillips screw (I) with nylon shoulder washers (H), or
using four M8 x 15 mm phillips screws (J).
2
© 2010 Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Figure. 3.1 Figure. 3.1
D
A
B
A
C
H
DISPLAY
I or J
DISPLAY
C

ISSUED: 09-24-10 SHEET #: 125-9146-2 (6-25-13)
Visit the Peerless Web Site at www.peerlessmounts.com
5 of 5
Optional for Multiple Displays: Installing Spacer Kit (Sold Separately)
Slide spacers into tab of mounted wall plate as shown. Keeping spacers ush against wall plate, fasten two
#10 x 3/4"wood screws as shown. There must be two spacers placed on the same side as the additional
wall plate. Align the tabs of the additional wall plate ush with the spacers. Follow main instruction for proper
installation of additional wall plates.
4
MOUNTED
WALL PLATE
NOTE: SUPPORTING SURFACE NOT SHOWN FOR CLARITY
NOTE: ADDITIONAL WALL PLATES SOLD SEPARATELY
ADDITIONAL
WALL PLATE
ADDITIONAL
WALL PLATE
DIAMOND CUT
VERTICAL
ORIENTATION
DIAMOND CUT
ROUND CUT
ROUND CUT
HORIZONTAL
ORIENTATION
MOUNTED
WALL PLATE
WALL PLATE ASSEMBLIES MAY BE DIFFERENT
THAN ILLUSTRATED