Pelican WF6 User manual

Owner’s Manual
Pelican WF6/WF10 Iron/Manganese
Filter & Salt Free Softener

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060Performance Circle, Suite 2, DeLand, FL 32724
Page 2
www.pelicanwater.com
[phone]
© Copyright 2019 Enviro Water Solutions Inc. All rights reserved.
All information contained herein is the property of Pelican Water Systems. Pelican Water Systems makes
no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Pelican Water Systems shall not be liable for technical
or editorial errors or omissions contained herein or for incidental or consequential damages in connection
with the furnishing, performance, or use of this material. The information is provided “as is” without
warranty of any kind and is subject to change without notice. This document contains proprietary
information which is protected by copyright. No part of this document may be photocopied, reproduced, or
translated into another language without the prior written consent of Pelican Water Systems. Pelican Water
Systems is anEnviro Water Solutions, Inc. company.
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060Performance Circle, Suite 2, DeLand, FL 32724
Page 3
www.pelicanwater.com
[phone]
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Operation and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Water Conditions for Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Complete Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Bypass Valve Installation. . . . .. . . . .. . . . .. . . . .. . . . .. . . ... . . ... . . ... . . ... . . 8
Carbon Soak . . . .. ... . .............. ........... .... . ......... ......10
Carbon Flush . . . . . . . . ... .. ... . .... .. ... . . ... ..... . .... . .... ..... .11
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Sediment Filter Assembly . . . ... . . ... . . ... . . ... . . . .. . . ... . .... . .... . .... .12
Sediment Filter Installation . ... . . . .. . . ... . . ... . . ... . .... . .... . . ... . .... .12
Chemical Injector Pump and Solution Tank Installation . . . . . . . . . . . . . . . . . . . . . . . . . 13
Chemical Injector Pump Installation . . . ... . . .. . . . . . .. . . . .. . . . .. . . . .. . . . . .14
Solution Tank Installation .. .. . . . .. . . . . . . . . .. . . . .. . . . .. . . . .. . . . . . . . . ..14
Iron and Manganese Tank Installation . . . . .. . . .. . . . . . .. . . . .. . . . . . . . . .. . . . ..15
Whole House Water Filter Tank Installation . . . . . . . .. . . . .. . . . ... . . . . . .. .. . . . ..17
Whole House Salt Free Water Softener/Conditioner Tank Installation .. . . .. . . . .. . . . ..19
NaturSoft - Media Soak . ... . . . .. . . ... . . ... . .... .. ..... . .... . .... . .... .20
NaturSoft - Media Flush . . . . . . . . . . . . . . . . . . . . . . . . . ... . . . .... . .... . .... .20
Complete the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Programming the Electronic Head .. . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . ... . . . .22
Step 1: Setting the Date & Time . . . . . . . .. . . . .. . . . .. . . . ... . . . . . .. .. . . . ..22
Step 2: Performing Manual Regeneration .. . . ... .. ... . .... . . ... . .... . .... .22
Testing Chlorine Levels in Water . . ... . . ... . . ... . . . .. ..... . .... ..... . .... .23
Flush your Hot Water Heater . . . . . . . .. . .. . . . .. . . . ... . . . . . .. .. . . . .. . . . ..24
What to Expect with your New Salt Free Water Softener/Conditioner .. . . . . . . .. . . . .. 24
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Replacing the Sediment Filter .. . . ... .. . .. . . ... . . ... ..... . .... . .... . .... . 26
Chemical Injector Pump . . . ... . . ... . . ... . . ... . . . .. ..... . .... . . ... . .... .26
Solution Tank Refill —Chlorine . . . ... . . . .. . . ... . . ... . . ... . .... . .... . .... .26
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Warranty Registration Form . ... . . ... . . . .. . . ... . . ... . .... . .... . .... . .... .29
Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installation Overview Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 4
www.pelicanwater.com
[phone]
Product Operation and Specifications
Important Information
Read these instructions carefully and determine the location of all system components before
beginning installation.
Check all applicable plumbing, building, and electrical codes for installation compliance.
Install the system on the main water supply.
Systems that contain electronic components cannot be installed outside in uncovered areas.
Water Conditions for Operation
The water should be free of hydrogen sulfide, a dissolved gas with a characteristic smell of rotten
eggs. If present, it can coat the catalytic surface of the media and interfere with the process. The gas
should be removed through adequate pre-treatment.
The water should be free of hydrocarbons, oils, and lubricants. If present, they can coat the catalytic
surface of the media and interfere with the process. Remove through adequate pre-treatment.
The water should contain less than 1 mg/l of phosphates. Phosphates sequester dissolved hardness
molecules preventing them from forming crystals and may coat the catalytic media surface and
interfere with the process.
The copper level in the water supply should be below the MCL of 1.3mg/L. If copper is present above
this level, it can attach to the surface of the catalytic media and interfere with the process.
WARNING:
If this or any other system is installed in a metal (conductive) plumbing system, i.e. copper or
galvanized metal, the plastic components of the system will interrupt the continuity of the
plumbing system. As a result any errant electricity from improperly grounded appliances
downstream or potential galvanic activity in the plumbing system can no longer ground
through contiguous metal plumbing. Some homes may have been built in accordance with
building codes, which actually encouraged the grounding of electrical appliances through the
plumbing system. Consequently, the installation of a bypass consisting of the same material
as the existing plumbing, or a grounded "jumper wire" bridging the equipment and re-
establishing the contiguous conductive nature of the plumbing system must be installed prior
to your systems use.
CAUTION:
When adding a filtration/softening system to homes/buildings supplied by well water, the system should be
installed following the pressure tank. DO NOT USE this system for pneumatic or hydro pneumatic
applications. If you are using a booster pump, then install this system following the booster
pump. If you have questions, please call customer service.
Specification Description WF6 WF10
Max Flow Rate 10 GPM 15 GPM
Minimum Working Pressure 25 PSI
Maximum Working Pressure 80 PSI
Maximum Vacuum 5 inch/127 mm Hg
Operating Temperatures 36°F – 100°F
pH Range 7 - 11
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 5
www.pelicanwater.com
[phone]
Complete Parts List
Note: Pelican supplies the parts below to accommodate a variety of water supply lines.
Table 1: Parts List
Part Description Qty. Part Description Qty.
1" Plastic Male NPT
Assembly:
V3007-04 WS1 Fitting 1"
Plastic Male NPT Assembly
(2): O-Rings (2), Split Rings
(2), and Connectors (2)
2Bypass Valve:
In/Out Bypass Valve with Red
Arrow Handles
2
1" PVC Tail Adaptor for
Electronic Head Bypass 2Hose Bib Assembly 1
Sediment Filter System:
Big Blue Filter Housing,
Mounting Bracket, Phillips
Head Screws (4), Bolt Head
Screws (4), and Washers (4)
1Bypass Valve for
Electronic Head 1
Sediment Filter:
5 Micron Poly-Spun
Sediment Filter
1Sediment Filter Wrench 1
Electronic Head 1Solution Tank 1
PVC Tubing Drain Line
(50 ft.) 1Chemical Injector Pump Tubing 1
Chlorine Test Strips 1Chemical Injector Pump 1
Non-Abrasive Auto Wax 1
M
EN
U
T
SE
(2) 1" Bushings Included
Bypass Allen Wrench Included
Rinse-Aid 1
90 degree 1" PVC Tail Adaptors
also included
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 6
www.pelicanwater.com
[phone]
Note: Drawings are not to scale.
Additional fittings will be needed to adapt to your plumbing.
Pelican Whole House
Water Filter 1 Pelican Whole House Iron & Manganese Filter 1
Pelican Salt Free Water
Softener/Conditioner 1
Part Description Qty. Part Description Qty.
Rev T

Page 7
Installation Overview Diagram
PPelican
Water Systems
  
 
  

5

DO NOT SCALE DRAWING



 
CONNECTION SIZE: 1"
MAX PRESSURE OPERATING: 80 PSI MAX TEMPERATURE: 120°
INSTALLATION OVERVIEW
WF 6/10
**BACKWASH LINE TO BE PLUMBED TO A DRAIN
SHUT OFF VALVES
INJECTION PUMP **
0
0
0
0
SEDIMENT FILTER
IRON
MANGANESE
FILTER
WATER
FILTER
BYPASS
SOLUTION
TANK
MENU
SET
HOSE SPIGOTS
NATURSOFT
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 8
www.pelicanwater.com
[phone]
Installation Overview
Figure 1
Pre-Installation
Bypass Valve Installation
Salt Free Water
Softener/Conditioner
Whole House
Water Filter
Outgoing
Water to
House
Whole House
Iron & Manganese Filter
IN
OUT
Sediment Filter
Incoming
Water
Supply
Wall Wall
Solution Tank
Electronic
Head
Chemical Injector
Pump Spigot
INLET
OUTLET
INLET
OUTLET
Figure 2
Whole House Water Filter & Salt Free Water Softener/Conditioner - The Bypass Valve comes pre-
assembled and ready to install with the O-Rings, Split Rings, and Quick Connect Nuts. Push the Bypass
Valve into the head of the Pelican Whole House Water Filter orSalt FreeWater Softener/Conditioner with
the unthreaded ends orientated towards the tank and hand-tighten the Quick Connect Nuts.
Whole House Iron & Manganese Filter - If the Red Clips are in the slots (female opening of Electronic
Head) remove them. Push the male O-Ring side of the Bypass Valve into the female opening of the
Electronic Head. Push the Red Clips back into the slots to tighten.
Quick
Connect Nut
Red Arrow
Water Filter
Head
Whole House
Iron & Manganese Filter
Electronic
Head
Bypass
Valve
INLET
OUTLET
Red
Clip
Front View
Whole House Water Filter &
Salt Free Water Softener/Conditioner
Drain Line
Barb
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page
www.pelicanwater.com
[phone]
Notice:
Figure A
Figure B
In Service
In Bypass
Bypass Operation
SERVICE BYPASS
Bypass Allen Wrench
The Bypass Valve on the Electronic Head can be set to Bypass or Service by turning the knobs on the
top of the valve. The valves can be difficult to turn by hand until the seals become saturated. Use the
supplied Bypass Allen Wrench to turn the knobs if necessary.
Note: The Red Arrows on the Whole House Carbon Filter Bypass may be pointing in a different direction
then shown. If this is the case, remove the Red Arrows by pulling them straight up. Turn them around
and reposition correctly onto the Bypass Valve so they are positioned as shown in the service posistion
below.
The Bypass Valve on the Whole House Water Filter can be set to Bypass or Service by turning the Red
Arrows on the top of the valve.
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 10
www.pelicanwater.com
[phone]
Water Filter - Carbon Soak
!IMPORTANT!
Your system will not be ready for use for a minimum of 48 hours while the Carbon Soak process takes
place. Please plan your installation accordingly.
Notice:
Water will flow out of the outlet side of the Bypass Valve during this process. Be sure you perform this
series of steps in a location suitable for water flow.
Figure 3
1. Attach a garden hose to the Hose Bib Assembly.
2. Connect the Hose Bib Assembly to theinlet side of the Bypass Valve and hand tighten.
3. Fill the Whole House Water Filter until water comes out of outlet side of the Bypass Valve.
4. Turn the water off.
5. Remove thegarden hose fromtheHose Bib Assembly. Do not remove the fitting.
6. Allow the carbon to soak for a minimum of 48 hours prior to installation.
Garden
Hose
Hose Bib
Assembly
INLET
Water
Bypass Valve
Whole House Water Filter
OUTLET
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 11
www.pelicanwater.com
[phone]
Water Filter - Carbon Flush
!IMPORTANT!
Do not perform the Carbon Flush until the CarbonSoak process is complete.
Notice:
Water will flow out of the outlet side of the Bypass Valve during this process. Be sure you perform this
series of steps in a location suitable for water flow.
Figure 4-1
1. Reattach thegarden hose to the Hose Bib Assembly.
2. Slowly turn on the water less than a1/4 turn on the hose spigot.
3. Run water through the inlet side of the Bypass Valve for 30 minutes to expel the carbon fines.
4. Turn off the water.
5. Remove the Hose Bib Assembly from the inlet side and attach it to the outlet side of the Bypass Valve.
6. Slowly, fully open the hose spigot.
7. Run the water through the outlet side for 3minutesto reset the carbon.
8. Turn off the water.
9. Remove the Hose Bib Assembly from the Bypass Valve and disconnect the garden hose.
Note: Please save the Hose Bib Assembly as this will be used in the future for the carbon replacement.
INLET
Water
Bypass Valve
Whole House Water Filter
Garden
Hose
Hose Bib
Assembly
OUTLET
INLET
Water
Bypass Valve
Whole House Water Filter
Garden
Hose
Hose Bib
Assembly
OUTLET
Figure 4-2
Carbon Flush
Carbon Reset
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 12
www.pelicanwater.com
[phone]
Installation
Sediment Filter Assembly
Figure 5
Sediment Filter Installation
Figure 6
Notice:
The Sediment Filter Housing comes with a 1” threaded female inlet/outlet and will require additional
fittings to adapt to your plumbing. A shut-off valve is recommended prior to the Sediment Filter System.
Sediment Filter Cover
Sediment Filter
O-Ring
Stand Pipe
Blue Filter Housing
1. Unscrew the cover from the Blue Filter Housing.
2. Remove the plastic covering from the Sediment Filter.
3. Place the Sediment Filter onto the Stand Pipe in the Blue Filter Housing and set aside.
Top View
Blue Filter Housing
Inlet Water
Supply
Mounting
Bracket
1. Shut off the water.
2. Attach the Filter Cover to the Mounting Bracket using the supplied Bolt Head Screws and
Washers. Make sure to properly orientate the IN and OUT to match your flow pattern.
3. Attach the Mounting Bracket to the wall using the supplied Phillips Head Screws.
4. Hand tighten the Blue Filter Housing and then using the supplied Filter Wrench lightly snug
the housing making sure not to over-tighten. (counter clockwise).
5. Determine the size of your inlet water supply line. Reducers may be needed to fit the 1”
Sediment Filter System.
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 13
www.pelicanwater.com
[phone]
Chemical Injector Pump Overview
Figure 7
Pressure Release Button - Allows you to relieve the air pressure after install and maintenance.
Flow Direction Arrow - Indicates the proper flow pattern depending on how the unit is install.
Dosage Adjustment - Allows you to increase or decrease the amount of solution injected per gallon of flow.
Dosage Lock Nut - Locks and unlocks the Dosage Adjustment for increasing and decreasing solution.
Suction Hose Nut - Compression nut the secures the injector tubing to the injector.
Chemical Injector Pump and Solution Tank Installation
Figure 8
Dosage Adjustment
Dosage Lock Nut Suction Hose Nut
Pressure Release Button
Flow Direction Arrow
Incoming
Water
Supply
Outgoing Water
to House
35 Gallon
Solution Tank
Chemical Injector
Pump Tubing
Chemical Injector Pump
Sediment Filter
Pump Foot Valve
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 14
www.pelicanwater.com
[phone]
Chemical Injector Pump Installation
!IMPORTANT!
Install the Chemical Injector Pump into the water supplyafter the Sediment Filter and before any other
filtration or softening system.
1. Determine the size and material of your incoming watersupply line from the Sediment Filter System.
2. Mount the ChemicalInjector Pump to the wall using the provided bracket. Line up the inflow and
outflow connections with the current water line.
3. Remove the two red thread protectors from inlets and discard. Injector Pump has 3/4" connections,
two 1" bushings are included.
4. Plumb the Injector Pump into your water line. The arrow on the body of the Injector Pump shows
the correct water flow direction. The water should enter and exit the pump following the direction of
the arrow.
Solution Tank Installation
1. Remove the black cap from the opening on the Solution Tank.
2. Drill one 1/2”hole intothe top of the Solution Tank.
3. Insert the end of the Chemical Injector Pump Tubing withthe pump foot valve connected, into the
hole which was covered by the black cap on the top of the Solution Tank.
4. Feed and pull the other end of the tubing through the drilled opening on the top of the Solution
Tank.
5. Determine the length of Chemical Injector Pump Tubing required for the foot valve to reach4" from
the bottom of the Solution Tank and cut tubing.
6. Connect the ChemicalInjector Pump Tubing to the suction valve on the Chemical Injector Pump by
removing the suction hose nut, place nut over tubing, push tubing onto suction valve and tighten
nut.
7. Fill the Solution Tank with 17 gallons of bottled water and proper cups of bleach. (see chart below)
!IMPORTANT! Ensure the Chemical Injector Pump Tubing is free of kinks and the Solution Tank is not
sitting directly on concrete. The cold temperatures held by concrete floors can separate your solution.
Concentration of Bleach
(% Sodium Hypochlorite) Number of Cups Gallons of Water
3.00% 12 17
5.25% 7 17
6.00% 6 17
8.25% 4.5 17
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 15
www.pelicanwater.com
[phone]
Iron and Manganese Tank Installation
Figure 9
1. Level the Whole House Iron & Manganese Filter.
Notice:
If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands
vertical. The bottom of the tank is round and the boot allows the tank to stand upright.
2. Determine the size and material of your incoming water supply line from the In-Line Injection Port
and choose the appropriate fittings required to connect it to the Bypass Valve.
CAUTION:
Do not over-tighten any of the fittings during installation.
Table 2: Bypass Valve Fittings
3. Remove the gray cap from the top of the Whole House Iron & Manganese tank.
4. Screw the Electronic Head onto the tank hand-tight.
5. Install the fittings onto the inlet and outlet, following the arrows on the Bypass Valve and head.
Part Description Qty.
1" PVC Tail Adaptor for
Electronic Head Bypass 2
Salt Free Water
Softener/Conditioner
Whole House
Water Filter
Outgoing
Water to
House
IN
OUT
Sediment Filter
Incoming
Water
Supply
Wall Wall
Solution Tank
Electronic
Head
Chemical Injector
Pump
Spigot
INLET
OUTLET
OUTLET
INLET
Whole House
Iron & Manganese Filter
6. Connect the incoming water supply to the fitting on the inlet side of the Bypass Valve.
7. Connect the outgoing water supply to the outlet side of the Bypass Valve.
8. Firmly press one end of the discharge Tubing Drain Line onto the barbed nose, and secure the
other end of the line to a drain.
Drain Line
Barb
Electronic Head
Bypass Valve
Tail Adaptors
Red Clips
Rev T

© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724 www.pelicanwater.com
[phone]
Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener Page 16
IMPORTANT!
•Ensure the PVC Tubing Backwash Drain
Line is not submerged and is free of kinks.
•Maximum vertical rise of the backwash line
is 6 feet.
•If incorporating two or more backwashing
systems make sure to keep the drain lines
separate.
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 17
www.pelicanwater.com
[phone]
Whole House Water Filter Installation
1. Level the Whole House Water Filter.
Notice:
If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands
vertical. The bottom of the tank is round and the boot allows the tank to stand upright.
Figure 10
2. Determine the size and material of your incoming water supply line from the Whole House Iron &
Manganese Filter and choose the appropriate plumbing required to adapt to the 1” Male NPT
Assembly.
CAUTION:
Do not over-tighten any of the fittings during installation.
Table 3: Bypass Valve Fittings
Note: The fitting below is designed with a ¼"give to allow for proper pipe alignment. It will not leak and
is intended to have some flexibility.
Part Description Qty.
1" Plastic Male NPT Assembly:
V3007-04 WS1 Fitting 1" Plastic Male NPT
Assembly (2): O-Rings (2), Split Rings
(2), and Connectors (2)
1
bag
Salt Free Water
Softener/Conditioner
Whole House
Water Filter
Outgoing
Water to
House
IN
OUT
Sediment Filter
Incoming
Water
Supply
Wall Wall
Solution Tank
Electronic
Head
Chemical Injector
Pump Spigot
O-Ring
Split Ring
Quick Connect Nut
INLET
OUTLET
OUTLET
INLET
Whole House
Iron & Manganese Filter
Drain Line
Barb
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 18
www.pelicanwater.com
[phone]
3. Install the fitting onto the inlet and outlet sides of the Bypass Valve. Follow the diagram supplied
with the fitting.
4. Connect the incoming water supply from the outlet of the Whole House Iron & Manganese
Tank to the inlet side of the Pelican Whole House Water Filter.
5. Connect the outgoing water supply to the outlet side of the Bypass Valve.
CAUTION:
Avoid high flow rates such as bathtub, utility sinks, hose bibs, multi-headed showers, body sprayers, or
anything that is considered high flow for the first 72 hours to avoid flow restrictions caused by carbon
blockage of the top basket inside the carbon tank.
Carbon dust may be released into the water lines of the house/building during the first few days of water
use after carbon tank installation. The carbon dust is harmless, but may give the water a gray
appearance that should diminish within a week or 10 days depending on water use.
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 19
www.pelicanwater.com
[phone]
Whole House Salt Free Water Softener/Conditioner Tank Installation
1. Level the NaturSoft Salt Free Water Softener/Conditioner.
Notice:
If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands
vertical. The bottom of the tank is round and the boot allows the tank to stand upright.
Figure 11
2. Determine the sizeand material of your incoming water supply line from the Whole House Water
Filter and choose the appropriate fittings required to connect it to the Bypass Valve.
CAUTION:
Do not over-tighten any of the fittings during installation.
Table 4: Bypass Valve Fittings
Note: The fitting below is designed with a ¼"give to allow for proper pipe alignment. It will not leak and
is intended to have some flexibility.
3. Install the fitting onto the inlet and outlet sides of the Bypass Valve. Follow the diagrams
supplied with the fitting.
4. Connect the incoming water supply from the outlet of the Pelican Whole House Water Filter to
the inlet side of the Pelican Salt-free Water Softener/Conditioner.
5. Connect the outgoing water supply to the outlet side of the Bypass Valve.
Part Description Qty.
1" Plastic Male NPT Assembly:
V3007-04 WS1 Fitting 1" Plastic Male
NPT Assembly (2): O-Rings (2), Split
Rings (2), and Connectors (2)
1
bag
Split Ring
O-Ring
Quick Connect Nut
Salt Free Water
Softener/Conditioner
Whole House
Water Filter
Outgoing
Water to
House
Whole House
Iron & Manganese Filter
IN
OUT
Sediment Filter
Incoming
Water
Supply
Wall Wall
Solution Tank
Electronic
Head
Chemical Injector
Pump Spigot
INLET
OUTLET
INLET
OUTLET
Drain Line
Barb
Rev T

Pelican WF6/WF10 Iron/Manganese Filter and Salt Free Softener
© 2019 Enviro Water Solutions, Inc.
3060 Performance Circle, Suite 2, DeLand, FL 32724
Page 20
www.pelicanwater.com
[phone]
NaturSoft - Media Soak
Figure 12
CAUTION:
The Whole House Water Filter MUST be in the bypass position during this process (see Figure above).
1. Open acold water faucet or spigot downstream of the Water Softener.
2. Slowly turn the water back on at the main shut-off valve allowing the system tofill with water.
The air being displaced will escape through the open fixture downstream.
3. Turn the arrows on the Bypass Valve into the Bypass Mode position to bypass the tank. This will
allow you to isolate the tank and restore water supply to the home/building during the NaturSoft
media soak.
4. Allow the tank to soak for at least 60 minutes.
NaturSoft - Media Flush
CAUTION:
The Pelican Whole House Water Filter MUST be in the bypass position during this process (see Figure).
1. After the tank has soaked for 60 minutes, turn the main water supply back on or turn the arrows
on the Bypass Valve back into their original position.
2. Flush the system by running water for 5 minutes at a high flow rate of 5 GPM (this can be
achieved by using a bath tub or more than 3 faucets).
Note: The flush water may have a milky look to it. This is normal as calcium carbonate fines are
flushed from the system.
3. Rinse the system by reducing the flow rate to ½ GPM and run water for 60 minutes (this can be
achieved by turning one faucet ¼ of the way on).
4. Turn the Whole House Water Filter Bypass Valve back into service position. (out of Bypass).
Salt Free Water
Softener/Conditioner
Whole House
Water Filter
Outgoing
Water to
House
Whole House
Iron & Manganese Filter
IN
OUT
Sediment Filter
Incoming
Water
Supply
Wall Wall
Solution Tank
Electronic
Head
Chemical Injector
Pump Spigot
INLET
OUTLET
INLET
OUTLET
Drain Line
Barb
Rev T