PENCO TA50 User manual

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
Fasteners & Tools Needed
The following items are in the hardware kit
shipped with the locker:
8615–Number plate
8671–Aluminum Rivet
8621- Steel rivet
8709-Screw
8696- Coat Hook,
8717 Coat Rod Hook
6CR___-Coat Rod
You will need these tools to assemble the TA50
locker.
Rivet gun.
Drill with #3 Philips bit
Flat blade and Phillips head screwdrivers.
Stepladder
STEP 1- Check Parts
Unpack the component pieces for the basic locker.
You should have two sides, a back, a top, shelf, coat
rod hooks, coat rod, coat hooks, and bottom, for the
locker body. You should also have a left hand and a
right hand door.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
Note- Assemble locker upside down to
allow screw insertion into underside of
locker bottom. Images shown may differ
from your locker, as there are different
configuration options.Some parts show with
transparency in these instructions to add
clarity to assembly.
STEP 2 – Assemble the locker body
2A- Lay locker top on flat surface on the ground.
Insert the two sides onto the cast corner pieces of the
top assembly.
2B-1 Insert locker back into slot of the top.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2B-2 With the back inserted install one 8709 screw
on each side of the back about half way up. Note
holes are to align to make sure back is in proper
position.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2C-1 Insert cast corner pieces of locker bottom into
the side channels.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2C-2 Install one screw into each corner of the locker
bottom as shown.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2D- Next install one screw into the locker top in each
corner as shown.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2E- Now rotate locker body so the bottom is on the
ground.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2F-Install screws to locker back at U cut locations (6
inch intervals) on each side.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2G-1 Install mounting rails for shelf using one 8607
screw in the front upright and back upright.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2G-2 Insert shelf and attach shelf to rails using one
rivet in each corner.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2H-Now install 8696, 8717 coat hooks, and coat rod
using two rivets per hook.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
2I-Install doors using 8621 rivets at each hole
location on hinge.

Fully Framed TA50 LOCKER – KD
Assembly Instructions
www.pencoproducts.com
PENCO PRODUCTS, INC |1820 Stonehenge Drive, Greenville, NC 27858
800-562-1000 |Fax: [phone] |[e-mail]
Assembly is now complete. Lockers to be floor
and wall anchored before use.