Pentair Intellitouch ScreenLogic User manual

IntelliTouch ScreenLogic PDA Quick Start Guide
ScreenLogic
PDA
IntelliTouch ScreenLogic PDA Quick Start Guide
P/N 520602 Rev B
Quick Start Guide
pool/spa control system

IntelliTouch ScreenLogic PDA Quick Start Guide
Technical Support
Contact Technical Support at:
Sanford, North Carolina (8 A.M. to 5 P.M.)
Phone: [phone]
Fax: [phone]
Moorpark, California (8 A.M. to 5 P.M.)
Phone: [phone]
Fax: [phone]
Web site: visit www.pentairpool.com
Related IntelliTouch Manuals
IntelliTouch ScreenLogic User’s Guide (P/N 520493)
© 2005 Pentair Water Pool and Spa, Incorporated.
1620 Hawkins Ave., Sanford, NC 27330 • [phone]
10951 West Los Angeles Ave., Moorpark, CA 93021 • [phone]
All rights reserved. Information in this document is subject to change without notice.
Trademarks and Disclaimers. The trademark IntelliTouch, is a trademark of Pentair Water
Pool and Spa Inc. Other trademarks and trade names may be used in this document to refer
to either the entities claiming the marks and names or their products. Pentair Water Pool and
Spa Inc. disclaims proprietary interest in marks and names of others.
P/N 520602 Rev B - 01/06/05
IntelliTouch ScreenLogic PDA Quick Start Guide

ScreenLogic PDA Quick Start Guide
PDA First Time Setup Instructions
Thank you for purchasing the IntelliTouch ScreenLogic PDA
interface. Before you can use your PDA to operate your
ScreenLogic system, you need to setup the ScreenLogic PDA
program. The PDA must be in its cradle with power connected.
Charging the PDA
You need to charge the main battery and internal backup battery
from empty to full. This takes about 8 hours the first time and 4
hours thereafter, whether the device is on or off.
IMPORTANT: When you are not using your ScreenLogic PDA,
please return it to the cradle to replenish the battery. The PDA can
still be operated wirelessly in the cradle. The battery is good for
about a week without operation, and 2 to 3 hours of continuous
use.
Setting up the PDA for the first time
Before setting up the ScreenLogic PDA program, connect the AC
adapter to the cradle and to an electrical outlet, and insert the PDA
into the cradle.
Note: The following setup procedure assumes that you have
already connected the ScreenLogic wireless router and
Protocol adapter to a working IntelliTouch system.
To setup the ScreenLogic PDA program:
1. Press the power button on the front of the PDA. The Dell
opening screen is displayed.
2. Using the stylus, tap on the screen to setup your pocket PC.
3. Tap in the center of the 5 cross-hairs as they move across the
screen to align the touch screen.
4. Tap Next on the following screen.
1
ScreenLogic PDA Quick Start Guide
4
Notes

ScreenLogic PDA Quick Start Guide
5. Cut & Paste: Hold the stylus in the rectangle shaped box (9 to 10
o’clock) until you see the drop down menu display ‘Cut.”
6. Tap and hold 11:00 AM to paste then tap Next.
7. Select your time zone from the list, then tap Next.
8. Setup is complete. Tap the screen to begin using your device.
9. On the wireless screen, press the Wireless On/Off button as
indicated on the screen then tap the screen to continue.
10. Select the network “Pentair(x) where x is your network number.
Select the “Internet” button and tap “Connect”.
11. Your ScreenLogic network key is required. Your WEP
Encryption Key (10 digit number) is located on the bottom of
your ScreenLogic wireless router.
12. Place the cursor in the key field to open the virtual keyboard.
Enter the 10 digit WEP Encryption key (i.e. 1111111111).
13. Tap OK.
2
ScreenLogic PDA Quick Start Guide
3
14. The device will search and connect to the ScreenLogic wireless
router.
15. Tap the Start button and select Programs > File Explorer >
My Documents > My device > Built in storage.
16. Tap the “ScreenLogic” program file.
17. Tap OK to install ScreenLogic program. Wait for about 15
seconds for the installation process to begin.
18. Tap OK on the next dialog message box. Disregard this dialog.
19. The ScreenLogic program is now installed. Tap the Xin the top
right corner of the screen, two times to exit and return to the
Main screen.
20. Tap the Start button and select Programs then tap
ScreenLogic to load ScreenLogic.
21. After the installation ScreenLogic can be run from the Program
Group or from the shortcut icon on the Start menu
Note: The above installation steps will have to be repeated if
the battery is ever allowed to fully discharge. Please always
return the PDA to its cradle when you are done using it.