Pentair Pentek uvs-110 User manual

PENTEK®MODELS UVS110, UV110, UV120, UVBB120

UV Water SYSteMS InStrUctIon ManUal

www.pentairaqua.com

MODELS

Model

Part #

(120v/60Hz)

Part #

(220v/50Hz)

UVS-110 163003 163004

UV-110 163005 163006

UV-120 163007 163008

UVBB-120 163009 163010

APPLICATION

Ultraviolet Water Disinfection

SPECIFICATIONS

Models: UVS-110 UV-110 UV-120 UVBB-120

Maximum Operating

Pressure

65 psi 65 psi 65 psi 65 psi

Temperature

Range

40-100˚F

(4.4-37.8˚C)

40-100˚F

(4.4-37.8˚C)

40-100˚F

(4.4-37.8˚C)

40-100˚F

(4.4-37.8˚C)

Flow Rate @ 60 psi

(4.1 bar)

1 gpm

(3.8 Lpm)

2 gpm

(7.6 Lpm)

8 gpm

(30 Lpm)

15 gpm

(56 Lpm)

Voltage (Domestic)

120v/60Hz 120v/60Hz 120v/60Hz 120v/60Hz

Voltage (Int’l)

220v/50Hz 220v/50Hz 220v/50Hz 220v/50Hz

CBU Cartridge

The UVS-110 and the UV-110 are supplied with a carbon block filter

cartridge which reduces sediment, bad taste and odor.

GENERAL PRECAUTIONS

Always disconnect the UV from the power

source. Follow the procedures provided in

this manual. Improper handling can result in

death or serious injury.

Do not look directly at the UV lamp. This can

cause retina/eye damage.

Do not touch the UV bulb. Any fingerprints or

dirt will reduce the efficiency of the bulb and

may cause it to explode.

Observe caution when inserting quartz sleeve

to prevent breakage and cracking, which may

result in injury and damage to unit.

NOTE: When handling the UV bulb hold only the plastic-

covered ends of the bulb. If the bulb has been touched,

remove bulb and clean with alcohol before reinserting.

If water pressure exceeds 65 psi, a pressure

regulator, set at less than 65 psi, must be installed

before the Ultraviolet system.

Install on cold water lines only.

Do not install where system is exposed to

direct sunlight.

Do not use wicking or sealing agents for fitting

connections. Plumbers tape is recommended.

This system must be protected from

freezing which can cause cracking of the

filter housing and water leakage.

Because of the product’s limited service life,

and to prevent costly repairs or possible water

damage, we strongly recommend that the bottom

of all opaque housings be replaced every ten

years. If the bottom of your housing has been

in use for more than this period, it should be

replaced immediately. Date the bottom of any

new or replacement housing to indicate the next

recommended replacement date.

NOTE: Filter cartridge life varies depending on filter type,

usage and water conditions

For the UVS-110 and UV-110

Allow a minimum of 12 inches clearance under the filter for

changing the cartridge, and above the system to allow the UV

bulb to be changed.

For the UV-120 and UVBB-120

Allow a minimum of 20 inches clearance under the filter for

changing the cartridge, and above the system to allow the UV

bulb to be changed.

CARTRIDGE REPLACEMENT

(for UVS-110 and UV-110 only)

Your cartridge should be replaced when there is a noticeable

drop in water flow at the faucet or tap, and/or when unpleasant

odors return (approximately every 6-9 months).

1. Turn off water supply to the system.

2. Open faucet to relieve water pressure to the housing.

3. Unscrew housing from cap. If housing sticks or is difficult to

open use an Pentek spanner wrench.

4. Remove used cartridge from housing, remove plastic sleeve

and discard cartridge.

5. Remove O-ring from groove below the threads of the

housing and wipe groove and O-ring clean. Lubricate O-ring

with silicone grease. Place O-ring back into the groove.

With two fingers wipe or press O-ring down into the groove.

Note: This step is important to ensure a proper filter seal.

Make sure that the O-ring is seated level in the groove.

6. Insert a new cartridge into the sump making sure that it

slips down over the sump standpipe.

7. Remove gasket from cartridge end and slide plastic

sleeve into center of cartridge then replace gasket on top

of cartridge.

8. Screw the sump onto the cap and hand-tighten. Do not over-

tighten. Make sure that the cap slips over the cap standpipe

9. Turn on the water supply to allow the unit to slowly fill

with water.

10. Check for leaks before leaving installation.

11. Each time that you use water from your unit for drinking or

cooking purposes, it is recommended that you run (flush)

the tap for at least 10 seconds prior to using water. This is

particularly important if the water tap is not used daily.

UV LAMP REPLACEMENT

1. Turn off all electrical power to the system by unplugging or

throwing the circuit.

2. Unscrew the UV control module from the mounting bracket (4

screws) for Models UV-110, UV-120 and UVBB-120. For Model UVS-

100, slide mounting bracket retainer to allow access to the UV bulb.

3. Slide the old bulb out and unplug from the control module.

Note: Hold the UV lamp only by the plastic covered ends of

the bulb.

4. Carefully discard the old UV lamp.

5. Holding the new UV lamp only by the plastic covered ends of the

bulb, plug the new UV lamp into the control module or power cord.

Slide the new bulb into the cartridge housing and reattach UV

control module or secure mounting bracket retainer (depending

on model).

6. Restore electrical power to unit.

7. Check for leaks.

2 • PENTEK®UV Water Systems Instruction Manual

PENTEK® UV Water Systems Instruction Manual • 3

4 • PENTEK®UV Water Systems Instruction Manual

UVS-110

REPLACEMENT PARTS

Part Desciption Part #

1. 10" Slim Line™ Housing 153017

2. O-ring 143026

3. CBU-10 155271-03

4. Plastic Sleeve 163518

5. Quartz Sleeve 163504

6. O-rings for Quartz Sleeve 163538

7. 1/2" Black Cap w/o pr SPECIAL ORDER

8. Spacer Bushing 163517

9. Mounting Bracket SPECIAL ORDER

10. UV Lamp 163503

11. Control Module (120v/60Hz)

Control Module (120v/60Hz)

163501 - for use with

UVS-110-1

163502 - for use with

UVS-110-2

12. SW-1 Wrench 150539

UV-110

REPLACEMENT PARTS

Part Desciption Part #

1. 10" Housing 153001

2. O-ring 143011

3. CBU-10 155271-03

4. Plastic Sleeve 163518

5. Quartz Sleeve 163509

6. O-rings for Quartz Sleeve 163516

7. Plunger Rod w/Retainer 163519

8. 1/2" Black Cap w/o pr SPECIAL ORDER

9. Spacer Bushing 163517

10. Mounting Bracket SPECIAL ORDER

11. UV Lamp 163508

12. Control Module (120v/60Hz)

Control Module (120v/60Hz)

163506 - for use with

UVS-110-1

163507 - for use with

UVS-110-2

13. SW-1 Wrench 150295

120 V/60 Hz

420 Amp

Control Module

SW-1

PENTEK® UV Water Systems Instruction Manual • 5

UV-120

REPLACEMENT PARTS

Part Desciption Part #

1. 20" Housing 153013

2. O-ring 143011

3. Gasket for Insert Sleeve 163515

4. Stainless Steel Insert Sleeve 163514

5. Quartz Sleeve 163513

6. O-rings for Quartz Sleeve 163516

7. Plunger Rod w/Retainer 163519

8. 3/4" Black Cap w/o pr SPECIAL ORDER

9. Spacer Bushing 163517

10. Mounting Bracket SPECIAL ORDER

11. UV Lamp 163512

12. Control Module (120v/60Hz)

Control Module (220v/50Hz)

163510 - for use with

UV-120-1

163511 - for use with

UV-120-2

13. SW-2 Wrench 150295

UVBB-120

REPLACEMENT PARTS

Part Desciption Part #

1. 20" BB Housing w/SS sleeve SPECIAL ORDER

2. O-ring 143273

3. Quartz Sleeve 163548

4. Plastic Holder w/O-rings 163543

5. Plastic Tube 163545

6. 11⁄2" Black Cap w/o pr 153541

7. Mounting Bracket SPECIAL ORDER

8. UV Lamp 163512

9. Control Module (120v/60Hz)

Control Module (220v/50Hz)

163542 - for use with

UVBB-120-1

163547 - for use with

UVBB-120-2

10. SW-3 Wrench 150296

MAINTENANCE

The quartz sleeve should be cleaned with warm soap and water

every three months.

UV bulb should be replaced every 9-12 months. The bulb does

not normally burn out, however the efficiency of the bulb

decreases after one year.

Contact your local water treatment professional for replacement

cartridge and bulb pricing or call 1-800-645-0267 for a dealer

near you.

Leaks

At inlet/outlet connections:

• Use Plumber tape.

Between cap and housing:

• Make sure that the O-ring is clean, lubricated and

properly seated.

• Hand-tighten the housing.

• Check cartridge length. If cartridge is too long, replace

with proper length cartridge.

At UV quartz sleeve:

• Turn off all electrical power to the unit by unplugging or

throwing the circuit.

• Remove UV lamp and unscrew housing (See UV lamp

replacement).

• Check quartz sleeve for cracks, leaks and loose fittings.

• Check that O-rings between quartz sleeve and cap are

secure and have not been cut or damaged.

• If the sleeve is broken replace with a new quartz sleeve

and new O-rings.

6 • PENTEK®UV Water Systems Instruction Manual

PENTEK® UV Water Systems Instruction Manual • 7

FILTRATION & PROCESSING SOLUTIONS

5730 NORTH GLEN PARK ROAD, MILWAUKEE, WI 53209

P: 262.238.4400 |WWW.PENTAIRAQUA.COM |CUSTOMER CARE: 800.279.9404 |tech-supportpentair.com

All Pentair trademarks and logos are owned by Pentair, Inc. or its affiliates. All other registered and unregistered trademarks and logos are the property of their

respective owners. Because we are continuously improving our products and services. Pentair reserves the right to change specifications without prior notice.

Pentair is an equal opportunity employer.