Pepperl+Fuchs HiD2844 User manual

Switch Amplifier
HiD2844
<4-channel isolated barrier
<24 V DC supply (bus powered)
<Dry contact or NAMUR inputs
<4 passive transistor outputs
<Line fault detection (LFD)
<Up to SIL 2 acc. to IEC/EN 61508
Function
This isolated barrier is used for intrinsic safety applications. It transfers digital signals (NAMUR sensors/mechanical contacts) from a hazardous
area to a safe area.
The proximity sensor or switch controls a passive transistor for the safe area load. The module output changes state when the input signal
changes state. The normal output state can be reversed with the selector switches on the side of the unit.
Line fault detection (LFD) can be selected or disabled via a selector switch.
During an error condition, the transistor reverts to its de-energized state and the LEDs indicate the fault. A separate fault output bus is available.
The fault conditions can be monitored via a Fault Indication Board.
This module mounts on a HiD Termination Board.
Connection
Zone 0, 1, 2
Div. 1, 2
HiD2844
I
II
SL2 SL1
11
14
+
-
8a
7a
17
18
8b
7b
12
15
10a
9a
13
16
9b
10b
1
4
5a
5b
+
-
2
5
1a
1b
I
II
10 kΩ
1.5 kΩ
10 kΩ
1.5 kΩ
III
IV
+
-
3
6
3a
3b
+
-
7
8
7a
7b
III
IV
10 kΩ
1.5 kΩ
10 kΩ
1.5 kΩ
+
-
+
-
+
-
+
-
+
-24 V DC
FAULT
1a, 1b
2a, 2b
6b
Termination Board
Technical Data
General specifications
Signal type Digital Input
Functional safety related parameters
Safety Integrity Level (SIL) SIL 2
Supply
Connection SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage Ur20.4 ... 30 V DC bus powered via Termination Board
Rated current Ir15 mA at 24 V (per channel)
Power dissipation 0.35 W at 24 V (per channel)
1
Release date: 2022-01-- 05 Date of
Release date: 2022-01-05 Date of issue: 2022-01-05 Filename: 121457_eng.pdf
Germany: [phone]Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: [phone] Singapore: [phone]
www.pepperl-fuchs.com pa-inf[email protected] [email protected]
[email protected].com

Technical Data
Input
Connection side field side
Connection SL2: 5a(+), 5b(-); 1a(+), 1b(-); 3a(+), 3b(-); 7a(+), 7b(-)
Rated values acc. to EN 60947-5-6 (NAMUR)
Connectable sensor types potential free contact or proximity sensor
Switching point contact open 0.2 ... 1.2 mA, contact closed 2.1 ... 6.5 mA
Line fault detection breakage 0 ... 0.2 mA, short-circuit 6.5 mA ... maximum value
Output
Connection side control side
Connection SL1: 8a(+), 7a(-); 8b(+), 7b(-); 10a(+), 9a(-); 9b(+), 10b(-)
Rated voltage Ur30 V
Rated current Ir50 mA
Output one optocoupled transistor per channel
Signal level 1-signal: (external voltage) -1 V
0-signal: blocked output (off-state current max. 50 µA, typical 5 µA)
Fault indication output
Connection SL1: 6b
Output type open collector transistor (internal fault bus)
Transfer characteristics
Switching frequency < 2 kHz
Galvanic isolation
Output/power supply functional insulation acc. to DIN EN 50178, rated insulation voltage 50 Veff
Output/Output functional insulation acc. to DIN EN 50178, rated insulation voltage 50 Veff
Indicators/settings
Display elements LEDs
Control elements DIP switch
Configuration via DIP switches
Labeling space for labeling at the front
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Conformity
Galvanic isolation EN 50178
Electromagnetic compatibility NE 21:2006
For further information see system description.
Degree of protection IEC 60529
Ambient conditions
Ambient temperature -20 ... 60 °C (-4 ... 140 °F)
Relative humidity 5 ... 90 %, non-condensing up to 35 °C (95 °F)
Mechanical specifications
Degree of protection IP20
Mass approx. 140 g
Dimensions 18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D)
Mounting on Termination Board
Coding pin 1 and 2 trimmed
For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate CESI 02 ATEX 086
Marking 1 II (1)G [Ex ia Ga] IIC , 1 II (1)D [Ex ia Da] IIIC
Input Ex ia, Ex iaD
Voltage Uo13.2 V
Current Io20 mA
Power Po66 mW
Supply
Switch Amplifier HiD2844
Release date: 2022-01-05 Date of issue: 2022-01-05 Filename: 121457_eng.pdf
2
Germany: [phone]Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: [phone] Singapore: [phone]
www.pepperl-fuchs.com pa-inf[email protected] [email protected]
[email protected].com

Technical Data
Maximum safe voltage Um250 V AC (Attention! Um is no rated voltage.)
Certificate PF 11 CERT 2109 X
Marking 1 II 3G Ex nA IIC T4 Gc [device in zone 2]
Galvanic isolation
Input/input safe electrical isolation acc. to EN 60079-11:2007, voltage peak value 60 V
Input/Output safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V
Input/power supply safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V
Directive conformity
Directive 2014/34/EU EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
CSA approval
Control drawing 366-005CS-12B (cCSAus)
IECEx approval
IECEx certificate IECEx TUN 04.0012
IECEx marking [Ex ia] IIC
General information
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals
where applicable. For information see www.pepperl-fuchs.com.
Assembly
HiD
2844
4 ch
Switch
Amplifier
PWR
STATUSFAULT
CH 1
CH 2
CH 4
CH 3
Front view
LED green:
Power supply
LEDs yellow:
Status output
channel 1 ... 4
Switch 1 ... 8
LEDs red:
Line fault
channel 1 ... 4
Place for
labeling
Switch Amplifier HiD2844
Release date: 2022-01-05 Date of issue: 2022-01-05 Filename: 121457_eng.pdf
3
Germany: [phone]Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: [phone] Singapore: [phone]
www.pepperl-fuchs.com pa-inf[email protected] [email protected]
[email protected].com

Release date: 2022-01-05 Date of issue: 2022-01-05 Filename: 121457_eng.pdf
HiD2844
4
Germany: [phone]Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: [phone] Singapore: [phone]
www.pepperl-fuchs.com pa-inf[email protected] [email protected].com
[email protected].com
Switch Amplifier
Configure the device in the following way:
• Push the red Quick Lok Bars on each side of the device in the upper position.
• Remove the device from Termination Board.
• Set the DIP switches according to the figure.
Configuration
Channel 3 and 4 (switch 5 ... 8) only for HiD2844.
Configuration
The pins for this device are trimmed to polarize it according to its safety parameter. Do not change!
For further information see system description.
Input CLOSE/Transistor OPEN
Input OPEN/Transistor CLOSE
Lead fault detection LFD enable
Input CLOSE/Transistor CLOSE
Input OPEN/Transistor OPEN
Lead fault detection LFD disable
Switch positions
Phase CH 1 LFD CH 1 Phase CH 2 LFD CH 2 Phase CH 3 LFD CH 3 Phase CH 4 LFD CH 4
SWITCH SETTINGS
INPUT/OUTPUT
OPERATION
1
CH1
3
CH2
5
CH3
7
CH4
OPEN-ENERGIZED
CLOSE-DE-ENERGIZED
ON ON ON ON
CLOSE-ENERGIZED
OPEN-DE-ENERGIZED
OFF OFF OFF OFF
INPUT FAULT
DETECTION
2
CH1
4
CH2
6
CH3
8
CH4
FAULT ENABLE ON ON ON ON
FAULT DI S A B L E OFF OFF OFF OFF
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
CAUTION
Refer to the instruction
manual to install and
operate the unit
SELECTION
1 2
CH 1
NOTE: CH 3 and CH 4 only for Mod. 2844
3 4
CH 2
5 6
CH 3
7 8
CH 4
ON
NOT IN USE
FOR THIS MODEL