Perfect Aire 3PAMSH18-MZO2 User manual
2 3
TABLE OF CONTENTS
4
8
UNIT PARTS .................................................................................................................................................................................... 8
(A) WALL-MOUNTED TYPE .............................................................................................................................................................................................8
(B) DUCT / CEILING TYPE ................................................................................................................................................................................................8
(C) FLOOR AND STANDING TYPE (CONSOLE).........................................................................................................................................................9
(D) COMPACT FOUR-WAY CASSETTE TYPE ............................................................................................................................................................9
OPERATING TEMPERATURE ..................................................................................................................................................10
FEATURES .....................................................................................................................................................................................11
PROTECTION OF THE AIR CONDITIONER ............................................................................................................................................................. 11
ENERGY SAVING TIPS...............................................................................................................................................................
13
OPERATION MODE SELECTION ...........................................................................................................................................13
MAINTENANCE............................................................................................................................................................................13
OPTIMAL OPERATION ..............................................................................................................................................................13
WHEN THE AIR CONDITIONER IS TO BE USED AGAIN: ...............................................................................................13
14
COMMON ISSUES......................................................................................................................................................................
TROUBLESHOOTING ................................................................................................................................................................
17
18
INSTALLATION ORDER.............................................................................................................................................................18
BEST INSTALLATION PRACTICES........................................................................................................................................19
20
21
22
INSTALLATION INSTRUCTIONS – OUTDOOR UNIT.......................................................................................................
STEP 1: SELECT INSTALLATION LOCATION ......................................................................................................................................................... 22
STEP 2: INSTALL DRAIN JOINT .................................................................................................................................................................................. 23
STEP 3: ANCHOR OUTDOOR UNIT........................................................................................................................................................................... 23
25
CONNECTION INSTRUCTIONS – REFRIGERANT PIPING ............................................................................................
STEP 1: CUT PIPES ......................................................................................................................................................................................................... 25
STEP 2: REMOVE BURRS.............................................................................................................................................................................................. 25
STEP 3: FLARE PIPE ENDS........................................................................................................................................................................................... 25
STEP 4: CONNECT PIPES............................................................................................................................................................................................. 26
INSTALLATION MANUAL
OWNER’S MANUAL
TABLE OF CONTENTS (Continued)
28
OUTDOOR UNIT WIRING..........................................................................................................................................................
........................................................................................................................................
WIRING FIGURE ...........................................................................................................................................................................30
ONE-TWO MODELS:....................................................................................................................................................................................................... 30
ONE-THREE MODELS: ................................................................................................................................................................................................... 33
ONE-FOUR MODELS: ..................................................................................................................................................................................................... 34
ONE-FIVE MODELS: ....................................................................................................................................................................................................... 36
WIRING FIGURE ...........................................................................................................................................................................38
39
EVACUATION INSTRUCTIONS ...............................................................................................................................................39
NOTE ON ADDING REFRIGERANT........................................................................................................................................
ELECTRICAL SAFETY CHECK ................................................................................................................................................................................... 41
GAS LEAK CHECK........................................................................................................................................................................................................... 41
42
BEFORE TEST RUN ....................................................................................................................................................................
TEST RUN INSTRUCTIONS .....................................................................................................................................................
43
INSTALLATION MANUAL CONTINUED
IMPORTANT NOTE:
Read this manual and SAFETY MANUAL(if any) carefully before installing or operating your new air
conditioning unit. Make sure to save this manual for future reference.
the packaging of the indoor unit (model dependent)
4 5
SAFETY PRECAUTIONS
WARNING
This symbol indicates the possibility
of personnel injury or loss of life.
CAUTION
This symbol indicates the possibility of
property damage or serious consequences.
WARNING
This appliance can be used by children aged from
8 years and above and persons with reduced
of experience and knowledge if they have been
given supervision or instruction concerning use
of the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision
This appliance is not intended for use by persons
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
PRODUCT USE WARNINGS
• If an abnormal situation arises (like a burning
disconnect the power. Call your dealer
or injury.
• Do not
objects into the air inlet or outlet. This may
at high speeds.
• Do not
• Do not operate the air conditioner in places
near or around combustible gases. Emitted
gas may collect around the unit and cause
explosion.
• Do not operate your air conditioner in a wet
room such as a bathroom or laundry room. Too
much exposure to water can cause electrical
components to short circuit.
• Do not expose your body directly to cool air
for a prolonged period of time.
• Do not allow children to play with the air
conditioner. Children must be supervised
around the unit at all times.
• If the air conditioner is used together with
•
highly recommended.
Read Safety Precautions Before Operation and Installation
WARNING or CAUTION.
SAFETY PRECAUTIONS (Continued)
CAUTION
•
the power if you are not going to use it for a
long time.
•
• Make sure that water condensation can drain
unhindered from the unit.
• Do not operate the air conditioner with wet
hands. This may cause electric shock.
• Do not use device for any other purpose than
its intended use.
• Do not climb onto or place objects on top of
the outdoor unit.
• Do not allow the air conditioner to operate for
long periods of time with doors or windows
ELECTRICAL WARNINGS
•
• Keep power plug clean. Remove any dust or
grime that accumulates on or around the plug.
• pull power cord to unplug unit. Hold the
• modify the length of the power supply
cord or use an extension cord to power the
unit.
• share the electrical outlet with other
• The product must be properly grounded at
may occur.
•
and clamp them securely to prevent external
forces from damaging the terminal. Improper
electrical connections can overheat and cause
connections must be made according to the
Electrical Connection Diagram located on the
panels of the indoor and outdoor units.
• All wiring must be properly arranged to
ensure that the control board cover can close
properly. If the control board cover is not
cause the connection points on the terminal to
•
disconnection device which has at least 3mm
current device (RCD) having a rated residual
disconnection must be incorporated in the
CLEANING AND
MAINTENANCE WARNINGS
•
before cleaning. Failure to do so can cause
electrical shock.
• Do not clean the air conditioner with excessive
amounts of water.
• Do not clean the air conditioner with
combustible cleaning agents. Combustible
TAKE NOTE OF FUSE SPECIFICATIONS
The air conditioner’s circuit board (PCB) is designed
with a fuse to provide over current protection.
6 7
SAFETY PRECAUTIONS (Continued)
PRODUCT INSTALLATION WARNINGS
Installation must be performed by an
authorized dealer or specialist. Defective
Installation must be performed according
to the installation instructions. Improper
accordance with the requirement of NEC and
CEC by authorized personnel only.)
Contact an authorized service technician
for repair or maintenance of this unit. This
appliance shall be installed in accordance
with national wiring regulations.
to fail.
support the unit’s weight. If the chosen
unit may drop and cause serious injury and
damage.
Install drainage piping according to the
instructions in this manual. Improper drainage
may cause water damage to your home and
property.
install the unit within 1 meter (3 feet) of
any combustible materials
Do not install the unit in a location that may
be exposed to combustible gas leaks. If
combustible gas accumulates around the
NOTE ABOUT FLUORINATED GASSES
(NOT APPLICABLE TO THE UNIT USING R290 REFRIGERANT)
refer to the relevant label on the unit itself
the packaging of the outdoor unit. (European
Union products only).
technician.
Product uninstallation and recycling must be
recommended.
Do not turn on the power until all work has
been completed.
When moving or relocating the air
installation of the unit.
please read the information for details in
SAFETY PRECAUTIONS (Continued)
•
(EN Standard Requirements).
•
(UL Standard Requirements)
•
(IEC Standard Requirements)
•
AMOUNT OF
REFRIGERANT TO
INSTALLATION
MINIMUM ROOM
AMOUNT OF
REFRIGERANT TO
INSTALLATION
MINIMUM ROOM
1.0 0.6 /1.8 /2.2 9 /1 /1 1.95 0.6 /1.8 /2.2 33 /4 /2.5
1.05 0.6 /1.8 /2.2 9.5 /1.5 /1 2.0 0.6 /1.8 /2.2 34.5 /4 /3
1.1 0.6 /1.8 /2.2 10.5 /1.5 /1 2.05 0.6 /1.8 /2.2 36 /4 /3
1.15 0.6 /1.8 /2.2 11.5 /1.5 /1 2.1 0.6 /1.8 /2.2 38 /4.5 /3
1.2 0.6 /1.8 /2.2 12.5 /1.5 /1 2.15 0.6 /1.8 /2.2 40 /4.5 /3
1.25 0.6 /1.8 /2.2 13.5 /1.5 /1 2.2 0.6 /1.8 /2.2 41.5 /5 /3.5
1.3 0.6 /1.8 /2.2 14.5 /2 /1.5 2.25 0.6 /1.8 /2.2 43.5 /5 /3.5
1.35 0.6 /1.8 /2.2 16 /2 /1.5 2.3 0.6 /1.8 /2.2 45.5/5 /3.5
1.4 0.6 /1.8 /2.2 17/2 /1.5 2.35 0.6 /1.8 /2.2 47.5/5.5 /4
1.45 0.6 /1.8 /2.2 18 /2 /1.5 2.4 0.6 /1.8 /2.2 49.5 /5.5 /4
1.5 0.6 /1.8 /2.2 19.5 /2.5 /1.5 2.45 0.6 /1.8 /2.2 51.5 /6 /4
1.55 0.6 /1.8 /2.2 21 /2.5 /2 2.5 0.6 /1.8 /2.2 54 /6 /4
1.6 0.6 /1.8 /2.2 22 /2.5 /2 2.55 0.6 /1.8 /2.2 56 /6.5 /4.5
1.65 0.6 /1.8 /2.2 23.5 /3 /2 2.6 0.6 /1.8 /2.2 58 /6.5 /4.5
1.7 0.6 /1.8 /2.2 25 /3 /2 2.65 0.6 /1.8 /2.2 60.5/7 /4.5
1.75 0.6 /1.8 /2.2 26.5 /3 /2 2.7 0.6 /1.8 /2.2 63 /7 /5
1.8 0.6 /1.8 /2.2 28 /3.5 /2.5 2.75 0.6 /1.8 /2.2 65 /7.5 /5
1.85 0.6 /1.8 /2.2 29.5 /3.5 /2.5 2.8 0.6 /1.8 /2.2 67.5 /7.5 /5
1.9 0.6 /1.8 /2.2 31/3.5 /2.5 2.85 0.6 /1.8 /2.2 70 /8 /5.5
8 9
UNIT PARTS AND MAJOR FUNCTIONS
UNIT PARTS
Panel frame
Rear air
intake grille
Front panel
Horizontal louver
LCD display window
Vertical louver
Manual control button (behind)
Remote control holder
Connective cable
Stop valve
Fan hood
Air outlet
Air inlet
Electric control cabinet
Wire control
refrigerant connecting pipe
Connective cable
Stop valve
Fan hood
UNIT PARTS AND MAJOR FUNCTIONS (Continued)
(at air outlet)
Air inlet
Remote control
Installation part
Display panel
refrigerant connecting pipe
Connective cable
Stop valve
Fan hood
Drain pump
(drain water from
indoor unit)
Drain hose
Air outlet
Air inlet
Display panel
Remote control
Connective cable
Stop valve
Fan hood
10 11
OPERATING TEMPERATURE
features may activate and cause the unit to disable.
UNIT PARTS AND MAJOR FUNCTIONS (Continued)
COOL mode HEAT mode DRY mode
Room Temperature
Outdoor Temperature
(For models with
NOTE:
NOTE:
To further optimize the performance of your unit, do the following:
• Keep doors and windows closed.
• Limit energy usage by using TIMER ON and TIMER OFF functions.
• Do not block air inlets or outlets.
•
UNIT PARTS AND MAJOR FUNCTIONS (Continued)
FEATURES
PROTECTION OF THE AIR CONDITIONER
• The compressor cannot restart for 3 minutes
after it stops.
• The unit is designed not to blow cold air on
is in one of the following three situations and
the set temperature has not been reached.
A) When heating has just started.
B) During defrosting.
C) Low temperature heating.
• The indoor or outdoor fan stop running when
defrosting (Cooling and heating models only).
• Frost may be generated on the outdoor unit
during a heat cycle when outdoor temperature
is low and humidity is high resulting in lower
•
will stop heating operations and start
defrosting automatically.
• The time to defrost may vary from
temperature and the amount of frost buildup
on the outdoor unit.
on the remote control. If the system has an
the same settings.
12 13
ENERGY SAVING TIPS
• DO NOT set the unit to excessive temperature
levels.
•
direct sunlight.
• Doors and windows should be kept closed to
keep cool or warm air in the room.
• DO NOT place objects near the air inlet and
of the unit.
•
ECONOMY mode if applicable.
•
remove the batteries from the remote control.
•
•
UNIT PARTS AND MAJOR FUNCTIONS (Continued)
The air conditioner turns to FAN ONLY mode
from COOL or HEAT mode.
When the indoor temperature reaches the set
only mode. The compressor will start again when
the indoor temperature rises on COOL mode or
falls on HEAT mode to the set point.
Droplets of water may form on the surface of the
indoor unit when cooling occurs in relatively high
the horizontal louver to the maximum air outlet
position and select HIGH fan speed.
Heating mode
The air conditioner draws in heat from the outdoor
unit and releases it via the indoor unit during
heat drawn in by the air conditioner decreases
between indoor and outdoor temperature. If a
comfortable temperature cannot be achieved with
you use a supplementary heating device.
Lightning or a car wireless telephone operating
nearby may cause the unit to malfunction.
Disconnect the unit from its power source and
control to restart operations.
Closing curtains during heating
also helps keep the heat in
Doors and windows should be kept closed
MANUAL OPERATIONS AND MAINTENANCE
OPERATION MODE SELECTION
While two or more indoor units are simultaneously
precedence over all other modes. If the unit
units can operate in HEAT mode only. For example:
If the unit initially started operates under COOL (or
mode except HEAT. If one of the unit selects HEAT
only) or the auto and operation indication light will
defrost and alarm indication light (if applicable) will
MAINTENANCE
perform the following tasks:
Select FAN ONLY mode and let the indoor fan
run for a time to dry the inside of the unit.
Disconnect the power supply and remove the
battery from the remote control.
Check components of the outdoor unit
periodically. Contact a local dealer or a
customer service center if the unit
requires servicing.
CAUTION
power supply.
OPTIMAL OPERATION
following:
•
no blowing directly on people.
• Adjust the temperature to achieve the highest
possible level of comfort. Do not adjust the
unit to excessive temperature levels.
• Close doors and windows in COOL mode or
HEAT mode.
• Use the TIMER ON button on the remote
controller to select a time you want to start
your air conditioner.
• Do not place any object near the air inlet or air
may be reduced and the air conditioner may
stop running.
•
cooling or heating performance may be
reduced.
• Do not operate unit with horizontal louver in
closed position.
WHEN THE AIR CONDITIONER
IS TO BE USED AGAIN:
•
accumulated on the rear air intake grille in
order to avoid the dust being dispersed from
the indoor unit.
•
disconnected.
•
• Check if the air outlet or inlet is blocked after
the air conditioner has not been used for a
long time.
14 15
TROUBLESHOOTING
SAFETY PRECAUTIONS
• The power cord is damaged or abnormally warm
• You smell a burning odor
• The unit emits loud or abnormal sounds
• A power fuse blows or the circuit breaker frequently trips
• Water or other objects fall into or out of the unit
DO NOT ATTEMPT TO FIX THESE YOURSELF! CONTACT AN AUTHORIZED SERVICE
PROVIDER IMMEDIATELY!
COMMON ISSUES
The following problems are not a malfunction and in most situations will not require repairs.
Issue Possible Causes
Unit does not turn on
when pressing ON/OFF
button
The unit changes from
COOL/HEAT mode to
FAN mode
The unit may change its setting to prevent frost from forming on the unit.
selected mode again.
The indoor unit emits
white mist
the conditioned air can cause white mist.
Both the indoor and
outdoor units emit
white mist
emitted due to moisture generated from the defrosting process.
The indoor unit
makes noises
A squeaking sound is heard when the system is OFF or in COOL mode.
The noise is also heard when the drain pump (optional) is in operation.
A squeaking sound may occur after running the unit in HEAT mode due to
expansion and contraction of the unit’s plastic parts.
TROUBLESHOOTING (Continued)
Issue Possible Causes
Both the indoor unit
and outdoor unit
make noises
A low hissing sound may occur during operation. This is normal and is caused
running or is defrosting. This noise is normal and is caused by the refrigerant
gas stopping or changing direction.
The outdoor unit
makes noises
Dust is emitted from
either the indoor or
outdoor unit
be emitted when the unit is turned on. This can be mitigated by covering the
unit during long periods of inactivity.
The unit emits
a bad odor
The fan of the outdoor
unit does not operate
Problem Possible Causes Solution
Poor cooling
performance
Temperature setting may be higher
than ambient room temperature Lower the temperature setting
The heat exchanger on the indoor
or outdoor unit is dirty
according to instructions
The air inlet or outlet of either
unit is blocked
obstruction and turn it back on
Doors and windows are open
Make sure that all doors and windows
are closed while operating the unit
Excessive heat is generated
by sunlight
Close windows and curtains during
periods of high heat or bright sunshine
Low refrigerant due to leak or
TROUBLESHOOTING
16 17
TROUBLESHOOTING (Continued)
Problem Possible Causes Solution
The unit is
not working
Power failure Wait for the power to be restored
Turn on the power
The fuse is burned out Replace the fuse
Remote control batteries are dead Replace batteries
been activated
Wait three minutes after restarting
the unit
The unit starts
and stops
frequently
There’s too much or too little
refrigerant in the system
Check for leaks and recharge the
system with refrigerant.
There's air or incompressible gas or
moisture has entered the system.
Evacuate and recharge the system
with refrigerant
System circuit is blocked
Determine which circuit is blocked
and replace the malfunctioning
piece of equipment
The compressor is broken Replace the compressor
The voltage is too high or too low Install a manostat to regulate
the voltage
Poor heating
performance
The outdoor temperature is lower
Check for leaks and recharge the
system with refrigerant
Cold air is entering through doors
and windows
Make sure that all doors and
windows are closed during use
Low refrigerant due to leak or
ACCESSORIES
Name Shape Quantity (PC)
Connecting pipe
assembly
Liquid side
Parts you must purchase
separately. Consult the dealer
about the proper pipe size of
the unit you purchased.
Gas side
Name of
Accessories Q’ty (pc) Shape Name of
Accessories Q’ty (pc) Shape
Manual Drain joint
(some models) 1
Transfer
connector
NOTE:
Pipe size
appliance to
appliance. To meet
sometimes the
pipe connections
need a transfer
connector
installed on the
outdoor unit .
Optional part
one indoor
unit)
Seal ring
(some models) 1
Outdoor Unit
Anti-Vibration
Pads
Optional part
pieces for
depending on
models)
The air conditioning system comes with the following accessories. Use all of the installation parts and
be purchased separately.
There are two types of remote controls: wired and wireless. Select a remote control based on customer
preferences and requirements and install in an appropriate place.
Refer to catalogues and technical literature for guidance on selecting a suitable remote control.
18 19
INSTALLATION ORDER
INSTALLATION SUMMARY
MC MC
4
5
INSTALLATION SUMMARY (Continued)
BEST INSTALLATION PRACTICES
• A SURGE PROTECTOR IS HIGHLY RECOMMENDED TO PREVENT DAMAGE TO THE EQUIPMENT DUE
TO ELECTRICAL FAILURE
• VERIFY THE WALL IS PLUMB. AN UNPLUMB WALL WILL CAUSE BLOWER WHEEL TO BE
UNBALANCED
• NEVER USE WIRE NUTS ON THE COMMUNICATION CABLE. CRIMP
TYPE CONNECTORS ARE ALLOWED
• WIRING BETWEEN INDOOR AND OUTDOOR UNITS IS POLARITY SENSITIVE.(EXAMPLE: IF INDOOR
OUTDOOR UNIT)
•
•
A MINIMUM OF 10 FT. LINE SET IS REQUIRED
RECOMMENDED AMOUNT OF REFRIGERANT. SEE INSTALLATION AND OPERATION MANUAL
OF LINE SET)
• USE OIL OR NYLOG ON THE THREADS AND TORQUE NUTS TO THE PROPER SPECIFIED VALUE.
SEE INSTALLATION AND OPERATION MANUAL
20 21
INSTALLATION DIAGRAM
Installation
plate
Mounting screw
ST3.9 × 25-C-H
Refrigerant
pipe
Remote
controller
holder
Clip anchor
(2)
1
2
3
5
4
1
Installation plate
Mounting screw
ST3.9 × 25-C-H
Clip anchor
(1)
Remote
controller
holder
5 4 3
2
The maximum
amount of the
connection cables is 5.
This section is for
reference only.
Air-break Switch
Drainage
Pipe
Air-break
Switch
Outdoor Unit
Power Cable
More than
More than
SAFETY PRECAUTIONS
•
locate studs.
•
to minimize vibration & excessive noise.
•
must be free from obstructions at all times.
• This illustration is for demonstration purposes
only.
• The actual shape of your air conditioner may
• Copper lines must be independently insulated.
NOTE: The installation must be performed in
accordance with the requirement of local and
national standards. The installation may be
Number of units that can be used together Connected units
Stop time 3 min or more
Power source voltage
Voltage drop during start
Interval unbalance
1 DRIVE 2 1 DRIVE 3 1 DRIVE 4 1 DRIVE 5
Max. length for all rooms
Max. length for one indoor unit
SPECIFICATIONS
32.8ft(10m)
Indoor unit
Indoor unit
Indoor unit
Outdoor unit
49ft(15m)
49ft(15m)
Max.Height difference
pipe and the drop height between the indoor and outdoor units meet the requirements illustrated in the
following diagram:
22 23
OUTDOOR UNIT INSTALLATION
Install the unit by following local codes and
INSTALLATION INSTRUCTIONS –
OUTDOOR UNIT
STEP 1: SELECT INSTALLATION LOCATION
choose an appropriate location. The following are
standards that will help you choose an appropriate
location for the unit.
Proper installation locations meet the following
standards:
;Meets all spatial requirements shown in
Installation Space Requirements above.
;Good air circulation and ventilation
;Firm and solid—the location can support
the unit and will not vibrate
;Noise from the unit will not disturb others
;Protected from prolonged periods of direct
sunlight or rain
;
appropriate measures to prevent ice
buildup and coil damage.
If the unit is frequently exposed to heavy
rain or snow:
Build a shelter above the unit to protect
it from the rain or snow. Be careful not to
If the unit is frequently exposed to
salty air (seaside):
Use outdoor unit that is specially designed
to resist corrosion.
DO NOT install unit in the following locations:
;Near an obstacle that will block air inlets
and outlets
;
where noise from the unit will disturb others
;Near animals or plants that will be harmed
by hot air discharge
;Near any source of combustible gas
;In a location that is exposed to large amounts
of dust
;In a location exposed to a excessive amounts
of salty air
SPECIAL CONSIDERATIONS
FOR EXTREME WEATHER
If the unit is exposed to heavy wind:
a barrier in front of the unit to protect it from
extremely heavy winds.
See Figures below.
OUTDOOR UNIT INSTALLATION (Continued)
STEP 3: ANCHOR OUTDOOR UNIT
The outdoor unit can be anchored to the ground or
the installation base of the unit according to the
dimensions below.
UNIT MOUNTING DIMENSIONS
and the distance between their mounting feet.
Prepare the installation base of the unit according
to the dimensions below.
IN COLD CLIMATES
is as vertical as possible to ensure swift water
STEP 2: INSTALL DRAIN JOINT
install the drain joint at the bottom of the unit.
joints depending on the type of outdoor unit.
If the drain joint comes with a rubber seal
(see
Fit the rubber seal on the end of the drain
joint that will connect to the outdoor unit.
Insert the drain joint into the hole in the base
pan of the unit.
facing the front of the unit.
Connect a drain hose extension (not included)
to the drain joint to redirect water from the
unit during heating mode.
If the drain joint doesn’t come with a rubber seal
(see
Insert the drain joint into the hole in the base
pan of the unit. The drain joint will click in
place.
Connect a drain hose extension (not included)
to the drain joint to redirect water from the
unit during heating mode.
A
B
D
W
H
W
H
24 25
OUTDOOR UNIT INSTALLATION (Continued)
OUTDOOR UNIT
DIMENSIONS (in)
MOUNTING
DIMENSIONS (in)
W H D Distance A Distance B
29.9 23.2 11.2
(760 590 285mm)
20.85
(530mm)
11.4
(290mm)
31.9 22 12.2
(810 558 310mm)
21.6
(549mm)
12.8
(325mm)
33.27 27.5 12.6
(845 700 320mm)
22
(560mm)
13.2
(335mm)
35.4 33.85 12.4
(900 860 315mm)
23.2
(590mm)
13.1
(333mm)
37.2 31.9 15.55
(945 810 395mm)
25.2
(640mm)
15.95
(405mm)
38.98 38 13.58
(990 965 345mm)
24.58
(624mm)
14.4
(366mm)
36.93 53.9 15.43
(938 1369 392mm)
24.96
(634mm)
15.9
(404mm)
35.4 46 13.8
(900 1170 350mm)
23.2
(590mm)
14.88
(378mm)
31.5 21.8 13.1
(800 554 333mm)
20.24
(514mm)
13.39
(340mm)
33.27 27.6 14.3
(845 702 363mm)
21.26
(540mm)
13.8
(350mm)
37.24 31.9 16.53
(946 810 420mm)
26.5
(673mm)
15.87
(403mm)
37.24 31.9 16.14
(946 810 410mm)
26.5
(673mm)
15.87
(403mm)
37.5 52.5 16.14
(952 1333 410mm)
24.96
(634mm)
15.9
(404mm)
37.5 52.5 16.34
(952 1333 415mm)
24.96
(634mm)
15.9
(404mm)
35 26.5 13.46
(890 673 342mm)
26.1
(663mm)
13.94
(354mm)
L A
L ≤ H L ≤ H 9.8” / 25 cm or more
H < L ≤ H 11.8” / 30 cm or more
L > H Can not be installed
INDOOR UNIT CAPACITY
(BTU/H) LIQUID GAS
7K/9K/12K ¼
12K/18K ¼
24K
L
H
300 cm / 118” or more
A
60 cm / 23.6”
or more
150 cm / 59”
or more
25 cm / 9.8”
or more
25 cm / 9.8”
or more
You must drill a hole in the wall for the refrigerant
indoor and outdoor units.
Determine the location of the wall hole based
on the location of the outdoor unit.
drill a hole in the wall.
NOTE:
sensitive components.
protects the edges of the hole and helps seal
can be connected with A and B systems.
REFRIGERANT PIPING CONNECTION
CONNECTION INSTRUCTIONS –
REFRIGERANT PIPING
STEP 1: CUT PIPES
future maintenance.
Measure the distance between the indoor
and outdoor units.
than the measured distance.
Make sure that the pipe is cut at
DO NOT DEFORM
PIPE WHILE CUTTING
the pipe while cutting. This will drastically reduce
CAUTION
• The branching pipe must be installed
cause malfunction.
• DO NOT install the connecting pipe until both
indoor and outdoor units have been installed.
• Insulate both the gas and liquid piping to
prevent water leakage.
STEP 2: REMOVE BURRS
piping connection. They must be completely
removed.
Hold the pipe at a downward angle to prevent
burrs from falling into the pipe.
burrs from the cut section of the pipe.
STEP 3: FLARE PIPE ENDS
the ends with PVC tape to prevent foreign
materials from entering the pipe.
Sheath the pipe with insulating material.
because you can’t put them on or change
Remove PVC tape from ends of pipe when
The end of the pipe must extend beyond
refrigerant enter the unit. The presence of other
and can cause abnormally high pressure in the
refrigeration cycle. This can cause explosion
and injury.
26 27
REFRIGERANT PIPING CONNECTION
accordance with the dimensions.
STEP 4: CONNECT PIPES
then connect it to the outdoor unit. You should
pressure pipe.
PIPING EXTENSION BEYOND FLARE FORM
Outer Diameter of A (in)
Pipe (in) Min. Max.
Ø 0.25 (Ø 6.35mm) 0.0275 (0.7mm) 0.05 (1.3mm)
Ø 0.375 (Ø 9.52mm) 0.04 (1.0mm) 0.063 (1.6mm)
Ø 0.5 (Ø12.7mm) 0.04 (1.0mm) 0.07 (1.8mm)
Ø 0.63 (Ø 16mm) 0.078 (2.0mm) 0.086 (2.2mm)
Ø 0.75 (Ø 19mm) 0.078 (2.0mm) 0.094 (2.4mm)
the pipes.
TORQUE REQUIREMENTS
Outer Diameter
of Pipe (in)
Tightening
Torque Flare shape
Ø 0.25 (Ø 6.35mm) 13 - 15 ft-lbs
Ø 0.375 (Ø 9.52mm) 23 - 29 ft-lbs
Ø 0.5 (Ø 12.7mm) 36 - 43 ft-lbs
Ø 0.63 (Ø 16mm) 42 - 52 ft-lbs
Ø 0.75 (Ø 19mm) 49 - 74 ft-lbs
DO NOT USE EXCESSIVE TORQUE
Excessive force can break the nut or damage
the refrigerant piping. You must not exceed
torque requirements shown in the table above.
NOTE:
Align the center of the two pipes that you will
connect.
by hand.
unit tubing.
to the torque values in above table.
inspect the end of the pipe for cracks and
CAUTION
• Ensure to wrap insulation around the piping.
Direct contact with the bare piping may result
in burns or frostbite.
• Make sure the pipe is properly connected.
Over tightening may damage the bell mouth
and under tightening may lead to leakage.
(Continued) REFRIGERANT PIPING CONNECTION (Continued)
NOTE: intertwine signal cable with
other wires. While bundling these items
signal cable with any other wiring.
After connecting the copper pipes to
signal cable and the piping together
with binding tape.
Thread this pipeline through the wall and
connect it to the outdoor unit.
the outdoor unit.
Open the stop valves of the outdoor unit to
indoor and outdoor unit.
CAUTION
Check to make sure there is no refrigerant leak
after completing the installation work. If there is a
evacuate the system (refer to the Air Evacuation
section of this manual).
NOTE ON MINIMUM BEND RADIUS
Carefully bend the tubing in the middle
according to the diagram below. bend
Bend the pipe with thumb
min-radius 3.9” (10cm)
28 29
WIRING
BEFORE PERFORMING ANY
ELECTRICAL WORK, READ
THESE REGULATIONS
All wiring must comply with local and national
installed by a licensed electrician.
All electrical connections must be made
according to the Electrical Connection
Diagram located on the panels of the indoor
and outdoor units.
If there is a serious safety issue with the
to install the unit until the safety issue is
properly resolved.
protector and main power switch should be
installed.
or circuit breaker that disconnects all poles
approved circuit breaker or switch.
Only connect the unit to an individual branch
circuit outlet. Do not connect another
appliance to that outlet.
Make sure to properly ground the air
conditioner.
resulting in product malfunction and possible
Do not let wires touch or rest against
moving parts within the unit.
any combustible materials.
touch the electrical components soon after
or more before you touch the electrical
components.
Make sure that you do not cross your
electrical wiring with your signal wiring. This
may cause distortion and interference.
The unit must be connected to the main
No other equipment should be connected to
the same power circuit.
Connect the outdoor wires before connecting
the indoor wires.
WARNING
BEFORE PERFORMING ANY ELECTRICAL
POWER TO THE SYSTEM.
NOTE ON AIR SWITCH
When the maximum current of the air
or leakage protection switch with protective
device shall be used (purchased separately).
The appliance should be wired according to
NEC and CEC requirements.
Indoor unit
Outdoor unit
Disconnect
(purchased seperately)
(purchased seperately)
Outdoor unit power wires Indoor & Outdoor
connective wires
(A)
NOTE: The cographs are for explanation
purpose only. Your machine may be slightly
WIRING (Continued)
OUTDOOR UNIT WIRING
WARNING
BEFORE PERFORMING ANY ELECTRICAL
POWER TO THE SYSTEM.
Prepare the cable for connection
cable size. Be sure to use
NOTE:
type according to the local electrical codes
and regulations.
Minimum Cross-Sectional Area of
Power and Signal Cables (For reference)
Rated Current of
Appliance (A)
Nominal Cross
> 3 and ≤ 6 0.75
> 6 and ≤ 10 1
> 10 and ≤ 16 1.5
> 16 and ≤ 25 2.5
> 25 and ≤ 32 4
> 32 and ≤ 40 6
CHOOSE THE RIGHT CABLE SIZE
NOTE: Please choose the right cable size
according to the Minimum Circuit Ampacity
indicated on the nameplate of the unit.
from both ends of the signal cable to reveal
c. Strip the insulation from the ends.
NOTE:
follow the wiring diagram found inside the
electrical box cover.
Remove the electric cover of the outdoor unit.
remove the protection board.
Cover
Screw
wire to its corresponding terminal.
Clamp down the cable with the cable clamp.
Insulate unused wires with electrical tape.
Keep them away from any electrical or metal
parts.
Reinstall the cover of the electric control box.
HARMONIC DECLARATION
shortcircuit power Ssc is greater than or equal
the user’s supply and the public system. It is
the responsibility of the installer or user of the
the equipment is connected only to a supply
shortcircuit power Ssc is greater than or equal
the user’s supply and the public system. It is
the responsibility of the installer or user of the
the equipment is connected only to a supply
30 31
WIRING (Continued)
WIRING FIGURE
CAUTION
terminal block of the indoor and outdoor units. For
special attention while connecting the wire.
OPTIONAL
or or
NOTE:
users wish to perform their own wiring. Run the
of the cord clamp.
Model A
OPTIONAL
OPTIONAL
OPTIONAL
Model B
OPTIONAL
OPTIONAL
OPTIONAL
Model C
OPTIONAL
OPTIONAL
OPTIONAL
Model D
OPTIONAL
OPTIONAL
OPTIONAL
Model E
OPTIONAL
OPTIONAL
OPTIONAL
Model F
OPTIONAL
OPTIONAL
OPTIONAL
POWER
SUPPLY
L(A)
S(A)
N(A) L(B) N(B)
S(B)
Y/G
WLN
L ( 1 )
Model G
OPTIONAL
OPTIONAL
OPTIONAL
WIRING (Continued)
Model I
Y/G
TO B
L(A) N(A) S(A) L(B) N(B) S(B)
POWER
SUPPLY
N
L
Y/G
TO A
OPTIONAL
OPTIONAL
OPTIONAL
Model J
S(B)
N(A)
N(B) L(B) L
L(A) N
S(A)
POWER
or
1(L) 2(N) 3(S) 1(L) 2(N) 3(S)
or
SUPPL Y
T O B
T O A
S(2)
S(1)
OPTIONAL
OPTIONAL
OPTIONAL
S(B)
N(A)
N(B) L(B) L
L(A) N
S(A)
POWER
SUPPL Y
T O B T O A
S(2)
S(1)
OPTIONAL
OPTIONAL
OPTIONAL
Model K
Model L
WW
S(B)
N(A)
N(B) L(B) L
L(A) N
S(A)
POWER
SUPPL Y
T O B T O A
S(2)
S(1)
OPTIONAL
OPTIONAL
OPTIONAL
POWER
SUPPLY
L(A)
S(A)
N(A) L(B) N(B)
S(B)
Y/G
WLN
L ( 1 )
Model H
OPTIONAL
OPTIONAL
OPTIONAL
NOTE: Use the magnetic ring
the connective cable of indoor and
outdoor units after installation. One
magnetic ring is used for one cable.
POWER
SUPPLY
L(A)
S(A)
N(A) L(B) N(B)
S(B)
WLN
L ( 1)
OPTIONAL
OPTIONAL
OPTIONAL
Model M
TO A
POWER
SUPPLY
L(A)
S(A)
N(A) L(B) N(B)
S(B)
WLN
L ( 1)
OPTIONAL
OPTIONAL
OPTIONAL
Model N
TO A
Model O
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model P
Model L
Model H
Model A
Model C
Model E
Model G
Model B
Model D
Model F
Model MModel M
Model N
Model I
Model OModel J Model PModel K
32 33
WIRING (Continued)
Model Q
OPTIONAL
OPTIONAL
OPTIONAL
Model R
OPTIONAL
OPTIONAL
OPTIONAL
1(A)
3(A)
2(A) 1(B) 2(B)
3(B)
Model S
OPTIONAL
OPTIONAL
TO A
L1 L2
OPTIONAL
POWER
SUPPLY
1 2 3 1 2 3
Model T
L1(A)
S(A)
L2(A) L1(B) L2(B)
S(B)
OPTIONAL
OPTIONAL
TO A
L1 L2
OPTIONAL
POWER
SUPPLY
1 2 3 1 2 3
OPTIONAL
Model U
OPTIONAL
OPTIONAL
To indoor
unit A
To indoor
unit B
or
or
L N
OPTIONAL
POWER
SUPPLY
Model V
L(A) N(A) S(A) L(B) N(B) S(B)
OPTIONAL
OPTIONAL
or
or
To indoor
unit A To indoor
unit B
or
or
L N
OPTIONAL
POWER
SUPPLY
Model W
L(A) N(A) S(A) L(B) N(B) S(B)
OPTIONAL
OPTIONAL
To indoor
unit A
or
or
To indoor
unit B
or
or
WIRING (Continued)
Model A
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model B
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model D
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model E
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model F
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
POWER
SUPPLY
N
L
OPTIONAL
Y/G
TO B TO C
Y/G
L(A) N(A) S(A) L(B) N(B) S(B) L(C) N(C) S(C)
Y/G
TO A
Model G
OPTIONAL
OPTIONAL
OPTIONAL
Model H
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model U
Model Q
Model A Model E
Model V
Model R
Model B Model F
Model S Model C Model G
Model W
Model T Model D Model H
34 35
WIRING (Continued)
Model I
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
1(L) 2(N) 3(S) 1(L) 2(N) 3(S) 1(L) 2(N) 3(S)
L(C) N(C) S(C)
OPTIONAL
or
or
To indoor
unit C
OPTIONAL
Model J
OPTIONAL
OPTIONAL
To indoor
unit A
To indoor
unit B
or
or
or
or
Model B
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model A
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
or or
1(L) 2(N) 3(S) 1(L) 2(N) 3(S) 1(L) 2(N) 3(S) 1(L) 2(N) 3(S)
Model E
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Y/G
TO B
L(A) N(A) S(A) L(B) N(B) S(B)
POWER
SUPPLY
N
L
Y/G
TO A
Y/G
TO B
L(C) N(C) S(C) L(D) N(D) S(D)
Y/G
TO A
Model F
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Y/G
TO B
L(A) N(A) S(A) L(B) N(B) S(B)
POWER
SUPPLY
N
L
Y/G
TO A
Y/G
TO B
L(C) N(C) S(C) L(D) N(D) S(D)
Y/G
TO A
Model F
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model G
L2
L1
LPPUSREWOP Y
1(A) 2(A) 3(A) 1(B) 2(B) 3(B) 1(C) 2(C) 3(C) 1(D) 2(D) 3(D)
TO A TO B TO D
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model H
L2
L1
LPPUSREWOP Y
L1(A) L2(A) S(A) L1(B) L2(B) S(B) L1(C) L2(C) S(C) L1(D)L 2(D) S(D)
TO A TO B TO D
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model I
L2
L1
LPPUSREWOP Y
1(A) 2(A) 3(A) 1(B) 2(B) 3(B) 1(C) 2(C) 3(C) 1(D) 2(D) 3(D)
TO A TO B TO D
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
L1(C) L2(C) S(C) L1(D)L 2(D) S(D)
Model J
L2
L1
LPPUSREWOP Y
L1(A) L2(A) S(A) L1(B) L2(B) S(B)
TO A TO B TO D
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model D
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
WIRING (Continued)
Model A
Model D
Model G
Model B
Model E
Model H
Model I
Model J
Model I
Model C
Model F
Model J
36 37
Mode K
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model L
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
L(C)
S(C)
N(C) L(D) N(D)
S(D)
OPTIONAL
OPTIONAL
OPTIONAL
Model M
OPTIONAL
OPTIONAL
To indoor
unit A
To indoor
unit B
or
or
or
or
To indoor
unit C
To indoor
unit D
WIRING (Continued)
Model A
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
or or
1(L)2(N) 3(S) 1(L) 2(N) 3(S) 1(L)2(N) 3(S) 1(L) 2(N) 3(S) 1(L) 2(N) 3(S)
Model B
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model D
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model E
L2
L1
LPPUSREWOP Y
1(A) 2(A) 3(A) 1(B) 2(B) 3(B) 1(C) 2(C) 3(C) 1(D) 2(D) 3(D) 1(E) 2(E) 3(E)
TO A TO B TO D TO E
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model F
L(C) N(C) S(C) L(D) N(D) S(D) L(E) N(E) S(E)
TO D TO E
TO C
L(A) N(A) S(A) L(B) N(B) S(B)
TO A TO B
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
N
L
LPPUSREWOP Y
OPTIONAL
Model G
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model H
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model I
L2
L1
LPPUSREWOP Y
1(A) 2(A) 3(A) 1(B) 2(B) 3(B) 1(C) 2(C) 3(C) 1(D) 2(D) 3(D) 1(E) 2(E) 3(E)
TO A TO B TO D TO E
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model J
L2
L1
LPPUSREWOP Y
L1(A) L2(A) S(A) L1(B)L 2(B) S(B) L1(C) L2(C) S(C) L1(D) L2(D) S(D) L1(E) L2(E) S(E)
TO A TO B TO D TO E
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
Model K
L2
L1
LPPUSREWOP Y
L1(A) L2(A) S(A) L1(B) L2(B) S(B) L1(C) L2(C) S(C) L1(D) L2(D) S(D) L1(E) L2(E) S(E)
TO A TO B TO D TO E
TO C
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
WIRING (Continued)
Model K
Model A
Model D Model H
Model E Model I
Model F Model J
Model G Model K
Model L
Model B
Model M Model C
38 39
WIRING FIGURE
CAUTION
these guidelines when performing wiring:
• Always have an individual power circuit
follow the circuit diagram posted on the inside
of the control cover.
• Screws fastening the wiring in the casing
transportation. Because loose screws may
tightly fastened.
•
•
•
at more than 90 percent of the rated voltage
marked on the name plate.
•
• Always install an earth leakage circuit breaker
in wet or moist areas.
• The following can be caused by a drop in
disturbance of normal functioning.
• Disconnection from a power supply must be
an air gap contact separation of at least 3mm
in each active (phase) conductors.
•
must be disconnected.
NOTE: To satisfy the EMC compulsory
please make sure you apply the correct
magnetic rings on your equipment according
to the wiring diagram that adhere to the your
equipment .
Please contact your distributor or installer to
get further information and purchase magnetic
rings (The supplier of magnetic ring is TDK
WIRING (Continued) AIR EVACUATION
Close the manifold gauge’s Low Pressure
been no change in system pressure.
NOTE: If there is no change in system
valve (high pressure valve). If there is a change
Insert hexagonal wrench into the packed
valve (high pressure valve) and open the valve
Watch the Pressure Gauge for one minute
to make sure that there is no change in
pressure. It should read slightly higher than
the atmospheric pressure.
Remove the charge hose from the service
port.
OPEN VALVE STEMS GENTLY
wrench until it hits against the stopper.
try to force the valve to open further.
high pressure and low pressure valves.
using the proper tool.
system is not connected with the indoor unit.
The valve must be tightened with a screw
nut. Check for gas leaks before operation to
prevent leakage.
PREPARATIONS AND PRECAUTIONS
Air and foreign matter in the refrigerant circuit
and cause injury. Use a vacuum pump and
from the system.
Evacuation should be performed upon initial
installation and when unit is relocated.
BEFORE PERFORMING EVACUATION
;Check to make sure the connective pipes
between the indoor and outdoor units are
connected properly .
;Check to make sure all wiring is connected
properly.
EVACUATION INSTRUCTIONS
Before using a manifold gauge and a vacuum
you know how to use them properly.
Connect the manifold gauge’s charge hose
to the service port on the outdoor unit’s low
pressure valve.
Connect the manifold gauge’s charge hose
from the to the vacuum pump.
Open the Low Pressure side of the manifold
gauge. Keep the High Pressure side closed.
Turn on the vacuum pump to evacuate the
system.
This manual suits for next models
7
Table of contents
Other Perfect Aire Air Conditioner manuals
Perfect Aire
Perfect Aire 1PAMSHQCW12-15 User manual
Perfect Aire
Perfect Aire M2OF-18HFN1-M User manual
Perfect Aire
Perfect Aire 5PAC6000 User manual
Perfect Aire
Perfect Aire ProAire 1PRNC6000 User manual
Perfect Aire
Perfect Aire 2PAMSH09-MZW User manual
Perfect Aire
Perfect Aire 3PAMSCH12 User manual
Perfect Aire
Perfect Aire 4PAC5000 User manual
Perfect Aire
Perfect Aire PASC10000 User manual
Perfect Aire
Perfect Aire Mission Series User manual
Perfect Aire
Perfect Aire 3PAMSHHQC18-MZO2 Operating manual
Perfect Aire
Perfect Aire 3PAMSH30B-SZW User manual
Perfect Aire
Perfect Aire 3PAHP18002 User manual
Perfect Aire
Perfect Aire Air Conditioner User manual
Perfect Aire
Perfect Aire 1PAMSH09-SZW-14.5 User manual
Perfect Aire
Perfect Aire 3PASC10000 User manual
Perfect Aire
Perfect Aire 2PACH8000 User manual
Perfect Aire
Perfect Aire 1PTC07A-3.5 User manual
Perfect Aire
Perfect Aire PORT8000 User manual
Perfect Aire
Perfect Aire 2PAC6000 User manual
Perfect Aire
Perfect Aire 2PAMSHQC12-17.5 Instruction Manual
Popular Air Conditioner manuals by other brands
Panasonic
Panasonic CS-WU12VKYF Series operating instructions
Olimpia splendid
Olimpia splendid maeStro Pro Instructions for installation, use and maintenance
Carrier
Carrier 42HVM109303 Service manual
Carrier
Carrier 38MHRBC12AA1 installation instructions
Snap-On
Snap-On POLARTEK EEAC330B manual
Samsung
Samsung AJ NBNDEH Series user manual
Friedrich
Friedrich CCW06B10B operating instructions
Admiral
Admiral AW-05CM1FLU use and care manual
Panasonic
Panasonic CU-E9GFE-2 operating instructions
Samsung
Samsung AQV12NSA Service manual
INVENTOR
INVENTOR V4MRFI-24 user manual
Trane
Trane Packaged TerminalAir Conditioners & Heat... Installation operation & maintenance
