Perfect Choice Swivel Dining Chair User manual

Parts Included:
1- Assembled Back
1- Assembled Seat
1- Set of Arms
1- Set of Interlocking Cross Supports
1- Swivel
2 - Arm Supports (left & right)
4 - Circular Lower Leg Supports/Footrests
4 - Lower Legs for Base
1 - Backboard
ASSEMBLY INSTRUCTIONS
Swivel Dining, Counter Height or Bar Height Chair
Tools Not Included but Required: 7/16" wrench, or socket & ratchet and a power drill
Tools Included: #2 Square Drive Bit, 4mm Allen Wrench
Stainless Steel Hardware Included:
8 - 3-1/2" Bolts
8 - 3" Bolts
2 - 2-1/2" Bolts
2 - 2-1/4" Hex Head Bolts
4 - 3" Lag Screws
4 - 4" Deck Screws
2 - 1-1/2" Lag Screws
5 - 2" Deck Screws
4 - 1-5/8" Deck Screws
22 - Flat Washers
14 - Lock Washers
14 - Nuts
6 - Lock Nuts
Step 1
1. Assembling the base. 1a:Take the set of interlocking cross supports and lock them together using a 2"
deck screw making sure the provided screw hole is facing up. 1b: Next take one of the four lower legs for
the base and attach one circular lower leg support using a 3" lag screw making sure to place the pocket of
the circular lower leg support towards the ground. Repeat for other 3 legs. 1c: Next, attach one lower leg
to the cross section you assembled in step 1a using a 4" deck screw.Then repeat with the 3 remaining legs.
Make sure to insert the circular support into each leg as you go. 1d: Next, ip the base over and nish
screwing the circular supports to each leg using the four 2" deck screws.
Assembled Seat Circular Lower
Leg Supports
Arms
Cross
Supports
Arm Supports
Lower Legs
Swivel
Hardware
Assembled Back
1a
1d
1b
Backboard
2. Attach the swivel to the seat using two 2-1/4" hex head bolts &
washers and two 1-1/2 lag screws & washers.The lag screws should
go into the wider swivel support.The bolts should go through the
swivel mechanism rst and then through the supports under the seat.
Place a at washer and lock nut onto each bolt and tighten.
Step 2
NOTE: Swivel will loosen after some use.
1c

477 Vogt Lane • Chilton, WI 53014 • 800-817-8833
www.perfectchoicefurniture.com • www.birdschoice.com
Your outdoor furniture is guaranteed
for 20 years to never crack, split or
fade.To clean, wash with soap and
water. For tough stains, use a
solution with water and soft scrub or
try our furniture cleaner.
3. Attach the seat to the base using four 3" bolts.You may need to rotate
the seat as you drop each bolt into place. It is easier to work all the way
around using the front of the seat as you rotate to each 3" bolt. Place a
at washer and lock nut onto each bolt and tighten.
Step 3
4. Determine your left and right assembled arm supports.The screws
holding the assembled arm supports together should face in towards
each other. Place a 3-1/2" bolt through all 8 holes of the assembled arm
supports and into the seat. Place a at washer, lock washer and nut
onto each bolt and hand tighten only.
Step 4
Step 55. Attach the arms using four 3" bolts.The bolts go from the
inside of the arm supports out through the arm. Place a at
washer, lock washer and nut onto each bolt and hand tighten
only.
6. Attach the back of the chair to the seat of the chair using
two 1-5/8" deck screws. Make sure to push the chair back
up tight to the seat.Then, place two 2-1/2" bolts down
through each arm into the upper back support of the chair
back. Place at washer, lock washer and nut onto each bolt
and fully tighten. Next, attach back board to the back of the
seat using two 1-5/8" drywall screws.The holes are offset
towards the top of the chair.
7. Go back and tighten all nuts.
8. Enjoy your swivel chair!
Step 6