PerkinElmer VICTOR Nivo User manual

VICTOR Nivo®Multimode Plate Reader
Installation Guide
Installation with Wi-Fi
A USB stick in the VICTOR Nivo design is included in the delivery (see photo).
It contains the user manual and additional documents.
Please check on a regular basis for software updates on the PerkinElmer website:
http://www.perkinelmer.com/lab-products-and-services/resources/software-downloads.html
1
Unpack the VICTOR Nivo instrument and position it on the working
space.
Remove the green adhesive strip (A).
If a dispenser is installed:
Open the dispenser cover and remove the transport protection foam
(B).
2
Connect the power socket on the rear of the instrument to the mains
power using the external power adapter (C) and the power cord.
3
Connect the TP-LINK wireless router (LAN/WAN socket) to the
Ethernet socket on the rear of the instrument using the provided LAN
cable (D).
4
Connect the wireless router (Power socket) to the USB power supply
using the TP-LINK external USB power cable (E). Plug the USB power
supply into a wall socket.
5
Switch on the VICTOR Nivo using the power switch (F).
6
Switch on your control device with wireless network capability (e.g. a
laptop).
•If you are using the optional laptop or tablet from PerkinElmer and
start it for the first time, the Windows 10 first start routine will
appear. Configure user name, password, language settings etc.
7
Connect your control device with the instrument:
•Make sure your wireless adapter is turned on.
•Connect to the wireless network (see default network name on the
router’s service card, labeled with Wi-Fi Name (SSID)).
•Enter the password (see default password, labeled with Wi-Fi
Password/PIN).
To change the SSID network name and password of your wireless
network, please refer to the router´s manual.
8
Open your web browser to connect to the VICTOR Nivo. Type
http://192.168.0.2 into the address bar and press the Enter key.
The user interface appears and the instrument is initialized
automatically.
7 8 9 1 +
B
Instrument
LAN
Control Device
USB
Power Supply
Wireless
Router
C
D
E
F
HH35940060 (EN) · Rev. C · 2019-05-16
A

Installation with direct LAN cable connection
A USB stick in the VICTOR Nivo design is included in the delivery (see photo).
It contains the user manual and additional documents.
Please check on a regular basis for software updates on the PerkinElmer website:
http://www.perkinelmer.com/lab-products-and-services/resources/software-downloads.html
1
Unpack the VICTOR Nivo instrument and position it on the working
space.
Remove the green adhesive strip (A).
If a dispenser is installed:
Open the dispenser cover and remove the transport protection foam
(B).
2
Connect the power socket on the rear of the instrument to the mains
power using the external power adapter (C) and the power cord.
3
Connect the Ethernet port on the rear of the instrument to the Ethernet
port of your control device (e.g. laptop) using the LANnetwork cable
(D).
4
Switch on the instrument using the power switch (E).
5
Switch on your control device (e.g. a laptop).
•If you are using the optional laptop or tablet from PerkinElmer and
start it for the first time, the Windows 10 first start routine will
appear. Configure user name, password, language settings etc.
6
Configure the network settings of your control device (to match the IP
address of the VICTOR Nivo instrument):
Windows:
•Open the Windows “Control Panel” and go to the “Network and
sharing center”.
•Click on “Change adapter settings”.
•Right-click on “Local Area Connection” and select “Properties”.
•Enable “Internet Protocol Version 4 (TCP/IPv4)” and open its
“Properties”.
•Select “Use the following IP address”in the pop-up window and set
the “IP address” to 192.168.0.100 and the “Subnet mask” to
255.255.255.0.
•Confirm the settings by clicking “OK” in all open windows.
Make sure to enable “Obtain an IP address automatically”again, if
switching to Wi-Fi connection later!
7
Open your web browser to connect to the instrument. Type
http://192.168.0.2 into the address bar and press the Enter key.
The user interface appears and the instrument is initialized
automatically.
Instrument
LAN
Control Device
C
D
E
B
A